Need some opinions please - The 1947 - Present Chevrolet & GMC Truck Message Board Network

jay6891 · 12-18-2009, 03:50 PM

Well after several years of collecting parts I think that I am ready to tear my truck apart. What I plan on doing is a static drop of 4 and 6. Fitting some 22 for the rear and 18 for the front. Starting on rear end now. Striped down the rear and when I knocked the u bolts out of the trailing arms. They, meaning the arms split at the seams. Old tack welds let go. So I finished them off on the split and got both halves separated. Cleaned them up and welded them solid all the way around. They feel some much more solid and heavier now. My questions are, Should I go ahead and weld some reinforcement plates on there like the factory? Or is it good enough? Also wanting to put a rear sway bar on. Have a CCP rear bar, instructions mount it on bottom of control arms. Looks like it would be a good way to snag on something. Can it be mounted on top for more clearance? Any, if any difference? Putting my c notch in now so the installation of arms will be next. Thanks for any and all help..... Jay

SCOTI · 12-18-2009, 04:04 PM

Welding them up was reinforcement enough. Anything more would be added weight w/o much benefit so you're good to go.

I offer one recommendation..... do not do the 18/22 combo. The 2" difference between 18/20 combo's is very noticeable; 4" difference just won't look right.

jay6891 · 12-18-2009, 04:23 PM

I have seen our trucks with 18 and 22's. And it looks good, IMO. Granted these were highly~highly modified trucks. And now that I think about it they were always aired out. Hmmm. . . It is just a thought, and I do appreciate your opinion. Keep em coming.

SCOTI · 12-18-2009, 06:11 PM

Quote:

Originally Posted by jay6891

I have seen our trucks with 18 and 22's. And it looks good, IMO. Granted these were highly~highly modified trucks. And now that I think about it they were always aired out. Hmmm. . . It is just a thought, and I do appreciate your opinion. Keep em coming.

Post up pics of an 18/22 combo. I've seen multiple 18/20 combos on here (even have a set); but I haven't seen the 18/22's done.

64shortc10 · 12-18-2009, 06:28 PM

18's and 22's on this burban!
Tony from Norcal

**N2TRUX** · 12-18-2009, 08:07 PM

Quote:

Originally Posted by 64shortc10

18's and 22's on this burban!
Tony from Norcal

That's a good looking Burb, but that is not a good example.

Keep in mind that jay6891 is only running a 4/6 drop. Staggered wheel sizes look great on 67-72 when they are slammed. Running an 18/22 with a mild drop is going to make the front wheel look tiny.

jephs422 · 12-18-2009, 06:36 PM

As long as the truck sits level, 18's and 22's aren't too bad. It has to sit level though. Any rake and it'll accentuate the difference.

jay6891 · 12-18-2009, 07:10 PM

here is one for sure 18/22.

jay6891 · 12-18-2009, 07:11 PM

What about the rear sway bar? On top of control arms, on bottom of control arms, or no bar at all. Survey Says!!!!

12-18-2009, 03:50 PM	#1
jay6891 Car Knocker Join Date: May 2001 Location: jefferson,arkansas Posts: 664	Need some opinions please Well after several years of collecting parts I think that I am ready to tear my truck apart. What I plan on doing is a static drop of 4 and 6. Fitting some 22 for the rear and 18 for the front. Starting on rear end now. Striped down the rear and when I knocked the u bolts out of the trailing arms. They, meaning the arms split at the seams. Old tack welds let go. So I finished them off on the split and got both halves separated. Cleaned them up and welded them solid all the way around. They feel some much more solid and heavier now. My questions are, Should I go ahead and weld some reinforcement plates on there like the factory? Or is it good enough? Also wanting to put a rear sway bar on. Have a CCP rear bar, instructions mount it on bottom of control arms. Looks like it would be a good way to snag on something. Can it be mounted on top for more clearance? Any, if any difference? Putting my c notch in now so the installation of arms will be next. Thanks for any and all help..... Jay Attached Images __________________ 68 c-10,91 sportside bed,350 .030 over,4 bolt,10-1 comp,2.05 intake/1.94 exhaust,1.6 Harland Sharp roller rockers,edelbrock rpm cam and intake w/750 carb, 700r4, 3.73 gears,Jacabbs Electronic Igntion w/Accel HEI distributer and super coil. ZR-1 roll pan, filled tailights. Blazer tank. Hidden hitch. 2 1/2" Flowmaster 40's. Parts bought but not installed>> ford 9" posi with disc. CCP front and rear lowering kit 4/5. Cab corners,foor boards,rockers, cab braces, Phatom grill, Painless wiring kit.

12-18-2009, 04:04 PM	#2
SCOTI Registered User Join Date: Apr 2001 Location: DALLAS,TX Posts: 22,071	Re: Need some opinions please Welding them up was reinforcement enough. Anything more would be added weight w/o much benefit so you're good to go. I offer one recommendation..... do not do the 18/22 combo. The 2" difference between 18/20 combo's is very noticeable; 4" difference just won't look right. __________________ 67SWB-B.B.RetroRod 64SWB-Recycle 89CCDually-Driver/Tow Truck 99CCSWB Driver All Fleetsides @rattlecankustoms in IG Building a small, high rpm engine with the perfect bore, stroke and rod ratio is very impressive. It's like a highly skilled Morrocan sword fighter with a Damascus Steel Scimitar..... *Cubic inches is like Indiana Jones with a cheap pistol.*

12-18-2009, 04:23 PM	#3
jay6891 Car Knocker Join Date: May 2001 Location: jefferson,arkansas Posts: 664	Re: Need some opinions please I have seen our trucks with 18 and 22's. And it looks good, IMO. Granted these were highly~highly modified trucks. And now that I think about it they were always aired out. Hmmm. . . It is just a thought, and I do appreciate your opinion. Keep em coming. __________________ 68 c-10,91 sportside bed,350 .030 over,4 bolt,10-1 comp,2.05 intake/1.94 exhaust,1.6 Harland Sharp roller rockers,edelbrock rpm cam and intake w/750 carb, 700r4, 3.73 gears,Jacabbs Electronic Igntion w/Accel HEI distributer and super coil. ZR-1 roll pan, filled tailights. Blazer tank. Hidden hitch. 2 1/2" Flowmaster 40's. Parts bought but not installed>> ford 9" posi with disc. CCP front and rear lowering kit 4/5. Cab corners,foor boards,rockers, cab braces, Phatom grill, Painless wiring kit.

12-18-2009, 06:28 PM	#5
64shortc10 Registered User Join Date: Jan 2007 Location: Winters, Ca. Posts: 1,069	Re: Need some opinions please 18's and 22's on this burban! Tony from Norcal Attached Images

12-18-2009, 06:36 PM	#7
jephs422 Registered User Join Date: Jun 2008 Location: Oxnard CA Posts: 301	Re: Need some opinions please As long as the truck sits level, 18's and 22's aren't too bad. It has to sit level though. Any rake and it'll accentuate the difference. __________________ Jeff Savaglio Scott's Hotrods Oxnard CA 93030

12-18-2009, 07:10 PM	#8
jay6891 Car Knocker Join Date: May 2001 Location: jefferson,arkansas Posts: 664	Re: Need some opinions please here is one for sure 18/22. Attached Images __________________ 68 c-10,91 sportside bed,350 .030 over,4 bolt,10-1 comp,2.05 intake/1.94 exhaust,1.6 Harland Sharp roller rockers,edelbrock rpm cam and intake w/750 carb, 700r4, 3.73 gears,Jacabbs Electronic Igntion w/Accel HEI distributer and super coil. ZR-1 roll pan, filled tailights. Blazer tank. Hidden hitch. 2 1/2" Flowmaster 40's. Parts bought but not installed>> ford 9" posi with disc. CCP front and rear lowering kit 4/5. Cab corners,foor boards,rockers, cab braces, Phatom grill, Painless wiring kit.

12-18-2009, 07:11 PM	#9
jay6891 Car Knocker Join Date: May 2001 Location: jefferson,arkansas Posts: 664	Re: Need some opinions please What about the rear sway bar? On top of control arms, on bottom of control arms, or no bar at all. Survey Says!!!! __________________ 68 c-10,91 sportside bed,350 .030 over,4 bolt,10-1 comp,2.05 intake/1.94 exhaust,1.6 Harland Sharp roller rockers,edelbrock rpm cam and intake w/750 carb, 700r4, 3.73 gears,Jacabbs Electronic Igntion w/Accel HEI distributer and super coil. ZR-1 roll pan, filled tailights. Blazer tank. Hidden hitch. 2 1/2" Flowmaster 40's. Parts bought but not installed>> ford 9" posi with disc. CCP front and rear lowering kit 4/5. Cab corners,foor boards,rockers, cab braces, Phatom grill, Painless wiring kit.

Thread Tools
Show Printable Version Email this Page
Display Modes
Switch to Linear Mode Hybrid Mode Switch to Threaded Mode



Register or Log In To remove these advertisements.

Register or Log In To remove these advertisements.