|
05-29-2010, 01:09 AM | #1 |
Registered User
Join Date: Nov 2009
Location: Hazlehurst, Ga.
Posts: 822
|
sandblast tailgate?
I think I am ready to clean my tailgate up and get it primed. I know I can do it with a da grinder, but that will take some time and elbow grease. It is an after market tailgate. Anyone think I could sandblast it without damaging it?
__________________
1972 Custom Deluxe LT1 Gen V Swap "Green Lantern" 1984 Silverado Red Baron-72 c10 Project |
05-29-2010, 01:14 AM | #2 |
Factory Strippers Rule!
Join Date: Mar 2009
Location: Shingle Springs, CA
Posts: 707
|
Re: sandblast tailgate?
Aftermarket tailgates are usually super thin metal, so I would be real careful if you sandblast it not to warp the crap out of it. Maybe a DA with some 120 would work if you have time.
__________________
"Feast your eyes on a feast of smoke." 67 Chevy Short Fleet PLAN: LQ9, 4L60, D60 Looking for School Bus Gauges - Help me out! |
05-29-2010, 01:53 AM | #3 |
Registered User
Join Date: Jan 2009
Location: topeka, ks
Posts: 49
|
Re: sandblast tailgate?
kiddie pool and evaporust.
|
05-29-2010, 03:11 AM | #4 |
Registered Cruiser
Join Date: May 2002
Location: Las Vegas NV
Posts: 2,230
|
Re: sandblast tailgate?
Get some paint stripper.
__________________
I intend to live forever. So far, so good. |
05-29-2010, 05:30 AM | #5 |
Senior Member
Join Date: Jan 2003
Location: daytonabeach
Posts: 22,956
|
Re: sandblast tailgate?
a tailgate would b pretty hard to warp for someone familar with proper blasting techniques
lo pressure and at a 45degree angle is the way i'd do it with sand
__________________
71c-10 350/2004r/4:11 lowered3/4 longbed/dead by hurricane MEANING OF DEATH::::: SOMEBODY ELSE GETS YOUR STUFF DONT BELIEVE EVERYTHING YOU THINK TAKE MY ADVISE;I DON'T USE IT ANYWAY |
05-29-2010, 09:59 PM | #6 |
Registered User
Join Date: Jul 2001
Location: North Louisiana
Posts: 4,501
|
Re: sandblast tailgate?
I agree, just don't concentrate on any area too much and be carefull with the big flat areas.
__________________
Wynne 70 CST short fleet Hugger orange & white, 350/350, ps, pb, air, tilt, tach/vac/speedwarning, original buckets, AM/FM, oak bed floor, shoulder belts, 3.5"/5.5" drop, 20" American Racing VN425s. Build thread 53 Chevy shortbed 69 Camaro Click here to subscribe Chevy GMC International Truck Club Louisiana Charter Member http://www.louisianaclassictruckclub.com |
05-30-2010, 10:06 AM | #7 |
Registered User
Join Date: Jan 2008
Location: St.Petersburg,Fl
Posts: 1,267
|
Re: sandblast tailgate?
I'd try Ospho and DA it afterward. .02
|
05-30-2010, 10:43 AM | #8 |
Senior Member
Join Date: Mar 2006
Location: Clarkrange Tennessee
Posts: 1,787
|
Re: sandblast tailgate?
find someone in you area that does media blasting. You can also buy a small media blaster from harbor freight.
Last edited by Ricks1971; 05-30-2010 at 10:43 AM. Reason: spelling |
05-29-2010, 09:47 PM | #9 |
Registered User
Join Date: Aug 2009
Location: St. Paul MN.
Posts: 1,996
|
Re: sandblast tailgate?
I used a wire cup on my 4 inch grinder
|
05-30-2010, 11:52 AM | #10 |
Registered User
Join Date: Sep 2007
Location: Brandon FL
Posts: 258
|
Re: sandblast tailgate?
Mine is the same way and I started on it with a "clean and strip" disc and it started to look good after just a couple minutes.
|
05-30-2010, 12:26 PM | #11 |
Registered User
Join Date: Dec 2009
Location: California, Maryland
Posts: 544
|
Re: sandblast tailgate?
I agree with bigsnookmaster to Ospho it afterwards. I had to blast, Ospho, lightly sand, and Ospho again with the deepest rust.
__________________
72 Fleet (died) 78 Step (sold) 55 Step named Fred (sold) 00 F150 68 Step (named El Scorcho by PO) Build thread for the new El Scorcho http://67-72chevytrucks.com/vboard/s...d.php?t=392932 |
Bookmarks |
Thread Tools | |
Display Modes | |
|
|