|
|
|
06-09-2010, 11:11 PM
|
#1 |
|
Registered User
Join Date: May 2010
Location: mexia,tx
Posts: 6
|
454 in a 67
has anyone put 454 in a 67 with headers and mt ? if what type of mods do i need to do?
Last edited by solo_0569; 06-09-2010 at 11:17 PM. |
|
|
|
06-09-2010, 11:48 PM
|
#2 |
|
Registered User
Join Date: Oct 2005
Location: Donna, Texas
Posts: 286
|
Re: 454 in a 67
I went with Solid motor mounts on my 68 and Hooker header Super Comps.
|
|
|
|
|
06-10-2010, 12:49 AM
|
#3 |
|
Registered User
Join Date: May 2010
Location: Calgary, Alberta
Posts: 14
|
Re: 454 in a 67
Check out this link. These guys used 72 BB motor mounts in their 67 Panel.
http://www.classicheartbeat.com/panel_8.htm Additionally I just bought a 1967 Stepside Shortbox with a 454 in it. The mounts in my truck look different than the ones above and as you can see from the picture the PO did not select the right headers and used a hammer to solve the problem. At some point in the future I'd like to redo this setup so hopefully someone else can advise on which mounts / headers would be the best. Not the full answer you were probably looking for but hope this helps a bit. |
|
|
|
|
06-10-2010, 12:56 AM
|
#4 |
|
Registered User
Join Date: May 2010
Location: Calgary, Alberta
Posts: 14
|
Re: 454 in a 67
I also found this picture. Not sure what type of headers these are but very nice clearance around the mount.
|
|
|
|
|
06-10-2010, 09:44 AM
|
#5 | |
|
Between Trucks...
Join Date: Mar 2002
Location: Los Angeles, CA.
Posts: 3,830
|
Re: 454 in a 67
Quote:
__________________
Beat it to fit, Paint it to match... 
|
|
|
|
|
|
06-10-2010, 04:03 PM
|
#6 | |
|
Registered User
Join Date: Mar 2003
Location: San Francisco, CA USA
Posts: 2,454
|
Re: 454 in a 67
Quote:
Ray Last edited by raycow; 06-10-2010 at 04:13 PM. |
|
|
|
|
|
06-10-2010, 04:34 PM
|
#7 |
|
Registered User
Join Date: May 2010
Location: mexia,tx
Posts: 6
|
Re: 454 in a 67
got motor in on stock mounts but need to know about headers and will they work with the z bar for the clutch. Are do i have swap to an auto tranny.
|
|
|
|
|
06-10-2010, 04:38 PM
|
#8 |
|
I dont drive fast,, I fly low!
Join Date: May 2010
Location: sheperdsville KY
Posts: 118
|
Re: 454 in a 67
its a bolt in swap.... u will just have to get the truck headers.... other than that it should be a bolt in swap .... good luck
__________________
____________ /_______  \(OO==||==OO) 67 GMC CUSTOM,72 GMC...65 chevelle...65 fastback mustang...75 VEGA...90 lx mustang...90 supercoupe...90 jeep wrangler...04 mach 1 mustang...06 toyota tacoma...08 nissan altima |
|
|
|
|
06-10-2010, 04:53 PM
|
#9 |
|
Registered User
Join Date: Oct 2005
Location: Donna, Texas
Posts: 286
|
Re: 454 in a 67
Hooker Headers
|
|
|
|
 |
| Bookmarks |
| Thread Tools | |
| Display Modes | |
|
|
Hybrid Mode
