What to do for shoulder harness seat belts? - The 1947 - Present Chevrolet & GMC Truck Message Board Network

**Dieselwrencher** · 08-02-2010, 03:45 PM

I am going over my longhorn project trying to get things ready to build it before the white crap flies. I want to make this thing wife and kid safe. I started going through what all this will need for a family to be safe. I decided I am going to add seat belts with lap and shoulder harnesses. I want to build this truck like it could have been ordered from GM even though it never was. So my question is this:, "What is everyone doing for shoulder belt seat belt upgrades that are close to OE style?" Am I better off just buying aftermarket new belts, or is it pretty easy to come up with decent OE shoulder belt set ups? I searched a little on here but haven't seen many OE sets available. Your thoughts and input are appreciated. Thanks Ryan.

blime81 · 08-02-2010, 03:55 PM

The belts out of an older "shoebox" S10 look pretty good in these trucks. The reel on the bottom is small and fits nicely where the old belt was.

The holes should be there in the top to bolt in the upper part.

Only trouble is finding a decent set at the yards.

Personally I put in seats out of a 01 Silverado that have the belts built in.

JOJABOY · 02-18-2013, 02:22 PM

Quote:

Originally Posted by blime81

The belts out of an older "shoebox" S10 look pretty good in these trucks. The reel on the bottom is small and fits nicely where the old belt was.

The holes should be there in the top to bolt in the upper part.

Only trouble is finding a decent set at the yards.

Personally I put in seats out of a 01 Silverado that have the belts built in.

I just put '89 Blazer belts in my '69. I ended up getting them off of ebay. I paid $100 for the two outside belts and ended up gettingmy money refunded because they never sent me the buckle end for one of them. Then I went to a pick a part and got the other buckle and center belt for $20. So, total investment is $20 and I have three black belts.

geezer#99 · 08-02-2010, 05:05 PM

Here's some pics of the ones I put in my 67 Gmc. Generic ones from LMC.

48richard · 08-02-2010, 05:33 PM

I put in the LMC belts too; they work OK, but the driver belt rubs on the gas tank unless you do some fancy bracket work. Also you have to pull then out very slowly or they lock up. Eventually I'm going to look for something better

**michael bustamante** · 08-02-2010, 05:43 PM

I have buckets out of a 03 siverado withthe seat belts in them. Ill have to put some reinforcement strips in the hole locations though

**Dieselwrencher** · 08-02-2010, 11:19 PM

Thanks for the replies guys!

Codypaul · 08-03-2010, 12:24 AM

mine are out of a 93 k1500. work great

**71blksuper4x4** · 08-03-2010, 12:52 AM

Ryan, the dealer installed shoulder harness setup is quite uncommon. Locating a set is fairly hard to do, but they do come up every once in awhile. Like many have chimed in, you make newer model truck belts work. Trevor

storm9c1 · 08-03-2010, 03:57 PM

Quote:

Originally Posted by 71blksuper4x4

Ryan, the dealer installed shoulder harness setup is quite uncommon. Locating a set is fairly hard to do, but they do come up every once in awhile. Like many have chimed in, you make newer model truck belts work. Trevor

Does anyone have good pics of the "uncommon" factory shoulder belts and how they work? I want to know what they look like in case they come up somewhere. I have original GM lap belts now but would like to upgrade with shoulder belts as well (while trying to keep it looking stock and period correct). Does the retractor change? Or is it a lap belt with an adapter for a shoulder belt using some sort of 3-way connection point that many cars used from that era? For example, Mopars commonly reused the standard lap belt but added a shoulder belt that latched in to the lap belt. It was a clunky setup, but it's part of having a car/truck from this era.

**leddzepp** · 08-03-2010, 04:01 PM

Quote:

Originally Posted by storm9c1

Does anyone have good pics of the "uncommon" factory shoulder belts and how they work? I want to know what they look like in case they come up somewhere. I have original GM lap belts now but would like to upgrade with shoulder belts as well (while trying to keep it looking stock and period correct). Does the retractor change? Or is it a lap belt with an adapter for a shoulder belt using some sort of 3-way connection point that many cars used from that era? For example, Mopars commonly reused the standard lap belt but added a shoulder belt that latched in to the lap belt. It was a clunky setup, but it's part of having a car/truck from this era.

The factory shoulder belts fasten just like the lap belts....You then have two male ends, and 2 female ends. They are not a 3-way connection point. Kind of a PITA to use. I have a set in my project for originality, NOT practicality.

Trevor and others have some great pics of them, I am sure someone will post a pic soon.

storm9c1 · 08-03-2010, 04:06 PM

Quote:

Originally Posted by leddzepp

The factory shoulder belts fasten just like the lap belts....You then have two male ends, and 2 female ends. They are not a 3-way connection point. Kind of a PITA to use. I have a set in my project for originality, NOT practicality.

Trevor and others have some great pics of them, I am sure someone will post a pic soon.

Yes, having 2 male ends and 2 female ends is what I was thinking. I'm used to that setup on all of my cars from that era, so I was wondering if the trucks are the same. Sounds like it is. The right latches and hardware setup are the hardest parts to find and visualize. The webbing can be redone reasonably easy.

jhwkns · 08-03-2010, 01:01 AM

S10 belts are great if you can find some

**leddzepp** · 08-03-2010, 02:25 AM

www.gemstreetrods.com

He has the best prices if you want new belts. Has the necessary brackets to avoid what 48Richard describes above, but you will have to have the female ends cut down (an upholstery shop can do this) as I believe is the case with all of these aftermarket belts. They are the same brand that LMC and other major suppliers carry, but his cost is much less. If I had to do it again, I would probably go with S-10 belts.

PanelDeland · 08-03-2010, 02:25 PM

Just a reminder,the original shoulder belts are 40 years old.The chances of them being deteriorated are huge.They probably wouldn't be safe unless you rewebbed tham.

**Dieselwrencher** · 08-03-2010, 03:41 PM

Quote:

Originally Posted by PanelDeland

Just a reminder,the original shoulder belts are 40 years old.The chances of them being deteriorated are huge.They probably wouldn't be safe unless you rewebbed tham.

I figured that after I typed it. But you never know what some of these guys are digging up for NOS OE parts lately.

pmpski_1 · 08-04-2010, 01:29 AM

Do the S-10 belts create a 3 point connection? And they work with bench seats?

camrycurt · 08-05-2010, 03:01 PM

Does anyone know what S10 model years fit well?

And, do the S10 and 93 K1500 belt setups that have been mentioned come with factory angle brackets to mount to the floor, or do you need to make floor brackets like was mentioned for the 91 Amigo?

This is a great thread. I just picked up a 70 C10 and want to add the shoulder belts. I'd at least like to stick with GM parts if possible, so the suggestions here are very helpful.

Thanks!

**Dieselwrencher** · 08-05-2010, 11:45 PM

I'm going to try to go to the junk yard this weekend and find something. We'll see.

*BAT* · 02-18-2013, 09:13 AM

Does anyone have pics to show how these are configured? I recently bought a pair of re-made shoulder belts and I am trying to figure out how they install.

54blackhornet · 02-18-2013, 01:45 PM

Google GM seatbelts and you can order new 3pt belts with GM logos, cost about 300.00

DO NOT PUT YOUR LIFE AHEAD OF MONEY !
Posted via Mobile Device

*BAT* · 02-18-2013, 01:58 PM

Quote:

Originally Posted by 54blackhornet

Google GM seatbelts and you can order new 3pt belts with GM logos, cost about 300.00

DO NOT PUT YOUR LIFE AHEAD OF MONEY !
Posted via Mobile Device

Thanks but as stated I already have them and I am trying to figure out how to install them.

*BAT* · 02-18-2013, 02:26 PM

Well I just found my answer http://67-72chevytrucks.com/vboard/showthread.php?t=385455, Post #6.

**FirstOwner69** · 02-18-2013, 02:40 PM

The picture in post 4 in this thread has a little more detail.

http://67-72chevytrucks.com/vboard/s...d.php?t=467785

08-02-2010, 03:45 PM	#1
Dieselwrencher 6>8 Plugless........ Join Date: Sep 2007 Location: Prairie City, Ia Posts: 17,142	What to do for shoulder harness seat belts? I am going over my longhorn project trying to get things ready to build it before the white crap flies. I want to make this thing wife and kid safe. I started going through what all this will need for a family to be safe. I decided I am going to add seat belts with lap and shoulder harnesses. I want to build this truck like it could have been ordered from GM even though it never was. So my question is this:, "What is everyone doing for shoulder belt seat belt upgrades that are close to OE style?" Am I better off just buying aftermarket new belts, or is it pretty easy to come up with decent OE shoulder belt set ups? I searched a little on here but haven't seen many OE sets available. Your thoughts and input are appreciated. Thanks Ryan. __________________ Ryan 1972 Chevy Longhorn K30 Cheyenne Super, 359 Inline 6 cylinder, Auto Trans, Tilt, Diesel Tach/Vach, Buckets, Rare Rear 4-link and air ride option Build Thread 1972 GMC Sierra Grande Longhorn 4x4 1972 Chevy Cheyenne Super K20 Long Step side tilt, tach, tow hooks, AC, 350 4 speed 1972 C10 Suburban Custom Deluxe 1969 Chevy milk truck 1971 Camaro RS 5.3 BTR STG3 Cam Super T10 1940 Ford 354 Hemi 46RH Ford 9" on air ride huge project *Tired of spark plugs? Check this out.*

08-02-2010, 03:55 PM	#2
blime81 Laid Lo Join Date: Aug 2008 Location: Oceanside CA Posts: 277	Re: What to do for shoulder harness seat belts? The belts out of an older "shoebox" S10 look pretty good in these trucks. The reel on the bottom is small and fits nicely where the old belt was. The holes should be there in the top to bolt in the upper part. Only trouble is finding a decent set at the yards. Personally I put in seats out of a 01 Silverado that have the belts built in. __________________ Semper Fi, Jeff '72 C10 - lays frame '07 Sand Rail - ecotec powered '05 2500HD - tows stuff '67 VW Bug - gas saver '01 Jeep TJ - rock crawler

08-02-2010, 05:05 PM	#4
geezer#99 Registered User Join Date: Aug 2009 Location: Bowser Posts: 13,731	Re: What to do for shoulder harness seat belts? Here's some pics of the ones I put in my 67 Gmc. Generic ones from LMC. Attached Images

08-02-2010, 05:33 PM	#5
48richard Registered User Join Date: Oct 2009 Location: Phoenix, AZ Posts: 475	Re: What to do for shoulder harness seat belts? I put in the LMC belts too; they work OK, but the driver belt rubs on the gas tank unless you do some fancy bracket work. Also you have to pull then out very slowly or they lock up. Eventually I'm going to look for something better __________________ 1971 C10 Longbed, 350/TH350

08-02-2010, 11:19 PM	#7
Dieselwrencher 6>8 Plugless........ Join Date: Sep 2007 Location: Prairie City, Ia Posts: 17,142	Re: What to do for shoulder harness seat belts? Thanks for the replies guys! __________________ Ryan 1972 Chevy Longhorn K30 Cheyenne Super, 359 Inline 6 cylinder, Auto Trans, Tilt, Diesel Tach/Vach, Buckets, Rare Rear 4-link and air ride option Build Thread 1972 GMC Sierra Grande Longhorn 4x4 1972 Chevy Cheyenne Super K20 Long Step side tilt, tach, tow hooks, AC, 350 4 speed 1972 C10 Suburban Custom Deluxe 1969 Chevy milk truck 1971 Camaro RS 5.3 BTR STG3 Cam Super T10 1940 Ford 354 Hemi 46RH Ford 9" on air ride huge project *Tired of spark plugs? Check this out.*

08-02-2010, 05:43 PM	#6
michael bustamante Senior Member Join Date: Sep 2007 Location: Albuquerque NM Posts: 7,862	Re: What to do for shoulder harness seat belts? I have buckets out of a 03 siverado withthe seat belts in them. Ill have to put some reinforcement strips in the hole locations though __________________ 1967custom

08-03-2010, 12:24 AM	#8
Codypaul Registered User Join Date: Apr 2010 Location: Duluth MN Posts: 64	Re: What to do for shoulder harness seat belts? mine are out of a 93 k1500. work great __________________ 1970 GMC K1500 1993 Chevy K2500

08-03-2010, 12:52 AM	#9
71blksuper4x4 SWB 4x4 Collector Join Date: Jun 2001 Location: Osage City, KS Posts: 5,156	Re: What to do for shoulder harness seat belts? Ryan, the dealer installed shoulder harness setup is quite uncommon. Locating a set is fairly hard to do, but they do come up every once in awhile. Like many have chimed in, you make newer model truck belts work. Trevor __________________ TREVOR 1970 CST swb 4x4 (speedwarning,cruise,tilt,tach,8track, original red shoulder belts,tow hooks) 1972 Jimmy (soon to be Hickey cloned) 1971 Cheyenne Super 4x4 swb (tilt,tach,buckets, original blue shoulder belts,am/fm,cruise,tow hooks, dealer 8 track) 1972 Cheyenne Super K20 4x4 Custom Camper (tilt, tach, am/fm, tow hooks, bed toolbox, aux gas tank 1972 Cheyenne Super Crew Cab K30 4x4 Duramax, Allison, np205, buckets, tow hooks (CURRENT PROJECT) http://67-72chevytrucks.com/vboard/s...d.php?t=624819 1989 V3500 Crew Cab (454tbi, NV4500, np205) 1970 Chevelle SS (LS5 454,th400,8track,buckets,tach) :2004 Jeep Wrangler Rubicon (daily driver) WTB: 1968-70 Cruise Control Lever

08-03-2010, 01:01 AM	#13
jhwkns Registered Cruiser Join Date: May 2002 Location: Las Vegas NV Posts: 2,230	Re: What to do for shoulder harness seat belts? S10 belts are great if you can find some __________________ I intend to live forever. So far, so good.

08-03-2010, 02:25 AM	#14
leddzepp Moderator Join Date: May 2007 Location: Southern Cal Posts: 20,031	Re: What to do for shoulder harness seat belts? www.gemstreetrods.com He has the best prices if you want new belts. Has the necessary brackets to avoid what 48Richard describes above, but you will have to have the female ends cut down (an upholstery shop can do this) as I believe is the case with all of these aftermarket belts. They are the same brand that LMC and other major suppliers carry, but his cost is much less. If I had to do it again, I would probably go with S-10 belts.

08-03-2010, 02:25 PM	#15
PanelDeland I am a Referee of life. Join Date: Jun 2000 Location: Greensboro N.C. Posts: 13,992	Re: What to do for shoulder harness seat belts? Just a reminder,the original shoulder belts are 40 years old.The chances of them being deteriorated are huge.They probably wouldn't be safe unless you rewebbed tham. __________________ The 47-present Chevrolet and GMC Truck Message Board Network,it's owners,moderators,members,and associates of any type should not be held responsible for my opinion. You can't fix stupid,not even with duct tape. "My appearance is due to the fact that "GOD" does punish you for having too much fun!" Barrett-Jackson has perfected alchemy,they make rust into gold! "You can lead a horse to water but you can't saddle a duck" "Cleverly disguised as a 'Responsible Adult' "Sometimes your Knight in shining armor is just a retard in tinfoil"

08-04-2010, 01:29 AM	#17
pmpski_1 Registered User Join Date: Jan 2006 Location: Seattle WA Posts: 505	Re: What to do for shoulder harness seat belts? Do the S-10 belts create a 3 point connection? And they work with bench seats? __________________ Curry in a Hurry: SB rebuild for my 71 C20

08-05-2010, 03:01 PM	#18
camrycurt Registered User Join Date: Jul 2010 Location: Leesburg, VA Posts: 420	Re: What to do for shoulder harness seat belts? Does anyone know what S10 model years fit well? And, do the S10 and 93 K1500 belt setups that have been mentioned come with factory angle brackets to mount to the floor, or do you need to make floor brackets like was mentioned for the 91 Amigo? This is a great thread. I just picked up a 70 C10 and want to add the shoulder belts. I'd at least like to stick with GM parts if possible, so the suggestions here are very helpful. Thanks!

08-05-2010, 11:45 PM	#19
Dieselwrencher 6>8 Plugless........ Join Date: Sep 2007 Location: Prairie City, Ia Posts: 17,142	Re: What to do for shoulder harness seat belts? I'm going to try to go to the junk yard this weekend and find something. We'll see. __________________ Ryan 1972 Chevy Longhorn K30 Cheyenne Super, 359 Inline 6 cylinder, Auto Trans, Tilt, Diesel Tach/Vach, Buckets, Rare Rear 4-link and air ride option Build Thread 1972 GMC Sierra Grande Longhorn 4x4 1972 Chevy Cheyenne Super K20 Long Step side tilt, tach, tow hooks, AC, 350 4 speed 1972 C10 Suburban Custom Deluxe 1969 Chevy milk truck 1971 Camaro RS 5.3 BTR STG3 Cam Super T10 1940 Ford 354 Hemi 46RH Ford 9" on air ride huge project *Tired of spark plugs? Check this out.*

02-18-2013, 09:13 AM	#20
BAT Account Suspended Join Date: Oct 2012 Location: Mt. Prospect IL Posts: 482	Re: What to do for shoulder harness seat belts? Does anyone have pics to show how these are configured? I recently bought a pair of re-made shoulder belts and I am trying to figure out how they install.



Register or Log In To remove these advertisements.

02-18-2013, 01:45 PM	#21
54blackhornet Registered User Join Date: Jul 2008 Location: Eastern Oregon Posts: 2,391	Re: What to do for shoulder harness seat belts? Google GM seatbelts and you can order new 3pt belts with GM logos, cost about 300.00 DO NOT PUT YOUR LIFE AHEAD OF MONEY ! Posted via Mobile Device __________________ 71 C-20 07 Magnum RT AWD

02-18-2013, 02:26 PM	#23
BAT Account Suspended Join Date: Oct 2012 Location: Mt. Prospect IL Posts: 482	Re: What to do for shoulder harness seat belts? Well I just found my answer http://67-72chevytrucks.com/vboard/showthread.php?t=385455, Post #6.

02-18-2013, 02:40 PM	#24
FirstOwner69 Senior Member Join Date: May 2010 Location: Wisconsin & Arizona Posts: 4,852	Re: What to do for shoulder harness seat belts? The picture in post 4 in this thread has a little more detail. http://67-72chevytrucks.com/vboard/s...d.php?t=467785

Thread Tools
Show Printable Version Email this Page
Display Modes
Switch to Linear Mode Hybrid Mode Switch to Threaded Mode

Register or Log In To remove these advertisements.