![]() |
Register or Log In To remove these advertisements. |
|
|
![]() |
|
Thread Tools | Display Modes |
|
![]() |
#1 |
Registered User
Join Date: Aug 2002
Location: Enid, OK
Posts: 55
|
![]()
To all the GMC owners,
I am trying to change both my parking lens in my 71 GMC. I am not sure how to change them out. Do I need a special tool to change these out? Any help would be appreciated. ![]() ![]() |
![]() |
![]() |
![]() |
#2 |
Half a bubble off!
Join Date: Jun 2000
Location: Winfield, Ks, USA
Posts: 5,588
|
Screwdriver always works for me.
__________________
Just call me LB. ![]() '71 Cheyenne, 402BB, hauls blondes, brunettes, or redheads. |
![]() |
![]() |
![]() |
#3 |
Senior Member
![]() Join Date: Mar 2000
Location: Rockville,In. USA
Posts: 3,720
|
Best method is take a cheap small C-clamp and grind the pad off the screw end and grind the end to a bevel, then very carefully insert rivet through lens from front and through housing place pad side of clamp on rivet head and tighten slowly, the bevel you have ground on end of threaded screw on clamp will split the blind rivet, if you have a blunt bevel you can continue to tighten until rivet is crushed flat on back BUT BE CAUTIOUS AS TO TIGHT AND YOU CRACK THE NEW LENS. If your bevel on screw was not blunt enough when point bottoms out the lens may still be lightly loose, if so you can blunt tip more after getting all rivets intially split then finish crushing them flat. You got it easy barn9 changing Chevy parklight lenses.
GMCPaul |
![]() |
![]() |
![]() |
#4 |
Registered User
Join Date: Aug 2002
Location: Enid, OK
Posts: 55
|
GMC Paul,
Thanks for the information, I got my parking lens' put on yesterday and going to get them installed on my truck tomorrow. I should be getting my truck back from the paint shop tomorrow. I will try and get some photo's posted when I get my truck. |
![]() |
![]() |
![]() |
#5 |
14.1 @ 96MPH
Join Date: Jul 2001
Location: Mesa, AZ
Posts: 2,811
|
Am I missing something here? I can't think of a lens on my truck I don't get at with a Phillips screwdriver...
![]()
__________________
Project1970 - LS1 Swap Complete! ![]() |
![]() |
![]() |
![]() |
#6 |
Half a bubble off!
Join Date: Jun 2000
Location: Winfield, Ks, USA
Posts: 5,588
|
Whoa! I didn't know GMC's were so complicated! Sorry I was such a smart-a**. Rivets? Sounds like a good spot for improvement. Glad I have a Chevy!
__________________
Just call me LB. ![]() '71 Cheyenne, 402BB, hauls blondes, brunettes, or redheads. |
![]() |
![]() |
![]() |
#7 |
Progress = 0%
Join Date: Nov 2001
Location: Kansas City, MO
Posts: 2,108
|
I replaced my rivets with small stainless steel screws/nuts. The grill covers them, so they aren't visible anyway.
__________________
Jason - '67 GMC swb | '57 Bel-Air 4dr hardtop | '56 210 4dr Wagon | 2000 GMC Sierra |
![]() |
![]() |
![]() |
Bookmarks |
Thread Tools | |
Display Modes | |
|
|