Angle plug head/header question - The 1947 - Present Chevrolet & GMC Truck Message Board Network

evilways · 10-09-2010, 06:35 PM

I am trying to locate a set of Long tube headers that will accommodate the angle plug heads, plus frame clearance. Anyone got a manufacturer part number or even some pics of these type headers. Thanks in advance

**El Jay** · 10-09-2010, 08:39 PM

Check with Stan's Headers. They have just about everything.
Although I don't have angle plug heads, I'm happy with the set (installed by P.O.) on my '69. But I do know they make them for angle plug heads

www.stans-headers.com/gm_headers.htm

Old Yeller 1970 · 10-09-2010, 08:40 PM

My Hooker Competition headers (Part Number 2452) work with my angle plug heads. They even clear my manual trans linkage. Fits all '67-72 Chevy, GMC 1/2, 3/4, 1 Ton PU, Suburbans, Blazers and, Jimmys with 283-400 CID engines. The spark plug boot on cylinder 5 is very tight. It doesn't touch the header pipe but I keep a ceramic sleeve on it just to be safe.

evilways · 10-10-2010, 11:18 AM

Thanks guys

bigsnookmaster · 10-11-2010, 08:35 AM

I run Hooker Super comps with no problem. # 5 is tight, but with a 90 degree boot, no problem.

10-09-2010, 06:35 PM	#1
evilways Registered User Join Date: Mar 2008 Location: Lafayette, IN Posts: 226	Angle plug head/header question I am trying to locate a set of Long tube headers that will accommodate the angle plug heads, plus frame clearance. Anyone got a manufacturer part number or even some pics of these type headers. Thanks in advance __________________ Mark 1967 C/10 stepside lwb daily driver 1968 C/10 fleetside lwb parts truck 1971 Cheyenne Super swb project

10-09-2010, 08:39 PM	#2
El Jay Gone to greener pastures Join Date: May 2007 Location: Gateway to the Delta Posts: 7,354	Re: Angle plug head/header question Check with Stan's Headers. They have just about everything. Although I don't have angle plug heads, I'm happy with the set (installed by P.O.) on my '69. But I do know they make them for angle plug heads www.stans-headers.com/gm_headers.htm __________________ '69 Chevy 1/2 T LWB Stepper: Daily Beater '72 GMC 3/4 T Fleet: Another Daily Beater '72 Plymouth Gran Coupe: ? "Ah women. They make the highs higher and the lows more frequent." Friedrich Nietzsche "Never kick a fresh turd on a hot day." Harry S. Truman GUN CONTROL: Never having to say, "I missed you." Always fire two warning shots into your attacker's chest area before putting a bullet between his eyes. Paraphrased from Louis Awerbuck

10-09-2010, 08:40 PM	#3
Old Yeller 1970 DON'T TREAD ON ME Join Date: May 2005 Location: Crosby County, TX Posts: 989	Re: Angle plug head/header question My Hooker Competition headers (Part Number 2452) work with my angle plug heads. They even clear my manual trans linkage. Fits all '67-72 Chevy, GMC 1/2, 3/4, 1 Ton PU, Suburbans, Blazers and, Jimmys with 283-400 CID engines. The spark plug boot on cylinder 5 is very tight. It doesn't touch the header pipe but I keep a ceramic sleeve on it just to be safe. __________________ Old Yeller Last edited by Old Yeller 1970; 10-09-2010 at 08:41 PM.

10-10-2010, 11:18 AM	#4
evilways Registered User Join Date: Mar 2008 Location: Lafayette, IN Posts: 226	Re: Angle plug head/header question Thanks guys __________________ Mark 1967 C/10 stepside lwb daily driver 1968 C/10 fleetside lwb parts truck 1971 Cheyenne Super swb project

10-11-2010, 08:35 AM	#5
bigsnookmaster Registered User Join Date: Jan 2008 Location: St.Petersburg,Fl Posts: 1,267	Re: Angle plug head/header question I run Hooker Super comps with no problem. # 5 is tight, but with a 90 degree boot, no problem. __________________ greg http://community.webshots.com/user/68406Stepside

Thread Tools
Show Printable Version Email this Page
Display Modes
Switch to Linear Mode Hybrid Mode Switch to Threaded Mode



Register or Log In To remove these advertisements.

Register or Log In To remove these advertisements.