![]() |
Register or Log In To remove these advertisements. |
|
|
![]() |
|
Thread Tools | Display Modes |
|
![]() |
#1 |
Registered User
Join Date: Dec 2010
Location: NC
Posts: 666
|
Kick panel vent question
On a factory air truck the passenger kick panel vent is operated via a vacuum canister. I have replaced my factory a/c unit with an aftermarket unit that no longer uses the vent for fresh air. I would like to convert the passenger vent to a pull handle arrangement like the driver side. I know trucks without factory air had pull handles on the passenger side too. My question is would I have to change the whole vent? Or can I remove the vacuum canister and spring and replace with a non-a/c style pull handle? Pics of non-a/c setups are appreciated as well. Just trying to figure out what all I need to change.
|
![]() |
![]() |
![]() |
#2 |
Old Skool Club
![]() Join Date: Jun 2001
Location: Benton, AR "The Heart of Arkansas"
Posts: 10,880
|
Re: Kick panel vent question
Sounds like a good plan, to me. If your aftermarket AC unit doesn't need fresh air in the same way that the OEM AC needed/used it, I don't know of any reason why you shouldn't use a Non-AC vent door. I've seen them in the Brother's catalogs.
__________________
Member Nr. 2770 '96 GMC Sportside; 4.3/SLT - Daily driven....constantly needs washed. '69 C-10 SWB; 350/TH400 - in limbo The older I get, the better I was. |
![]() |
![]() |
![]() |
#3 |
Registered User
Join Date: Jun 2011
Location: Richmond,Va
Posts: 2,934
|
Re: Kick panel vent question
Looks like if the door is the same all you need is the pull rod assembly. My 67 non a/c.
__________________
Nick Carter 1967 C10 Short bed Fleetside Project Cheap Thrills! 2WD C10 Modern/Performance Alignments Easiest Alignment Ever! |
![]() |
![]() |
![]() |
#4 |
Registered User
Join Date: Dec 2010
Location: NC
Posts: 666
|
Re: Kick panel vent question
Sweet. That is what I was hoping. I don't wanna have to actually replace the door/seal. Just curious: is that the driver or passenger side? Are they the same?
|
![]() |
![]() |
![]() |
#5 |
Registered User
Join Date: Jun 2011
Location: Richmond,Va
Posts: 2,934
|
Re: Kick panel vent question
I took a pic of the dr's side before I thought about it but looked over to the pass side. They are the same but side specific.
__________________
Nick Carter 1967 C10 Short bed Fleetside Project Cheap Thrills! 2WD C10 Modern/Performance Alignments Easiest Alignment Ever! |
![]() |
![]() |
![]() |
#6 |
Registered User
Join Date: Dec 2010
Location: NC
Posts: 666
|
Re: Kick panel vent question
Perfect! Thanks for taking time to snap the pic!
|
![]() |
![]() |
![]() |
#7 |
Registered User
Join Date: Jun 2011
Location: Richmond,Va
Posts: 2,934
|
Re: Kick panel vent question
Effortless on my part! Its Sunday and I've finished my chores. Watchin tv and clickin refresh every 15 minutes to see whats new!
__________________
Nick Carter 1967 C10 Short bed Fleetside Project Cheap Thrills! 2WD C10 Modern/Performance Alignments Easiest Alignment Ever! |
![]() |
![]() |
![]() |
#8 |
Registered User
Join Date: Dec 2010
Location: NC
Posts: 666
|
Re: Kick panel vent question
Lol same here.
|
![]() |
![]() |
![]() |
Bookmarks |
Thread Tools | |
Display Modes | |
|
|