|
04-08-2003, 12:57 AM | #1 |
No longer truckless
Join Date: Mar 2002
Location: Campbell, CA
Posts: 299
|
Roll cage is in. Pics
I got my K5 back the other day after having a friend build a cage for it. The cage is pretty sweet. The seats are incorporated into the cage & I had him set them up a little higher than stock. It's nice to be able to sit up high enough to see over the hood.
|
04-08-2003, 01:27 AM | #2 |
Senior Member
Join Date: Dec 1999
Location: Saskatchewan
Posts: 1,050
|
roll bar
thats a pretty sweet setup, can you post more pics of the rollbar with the tail gate down. Are you planing on putting a soft top on it?
thanks, Bernie
__________________
~70 GMCprostreet swb 396/700r NOS 575 hp "the Brick" ~72 chev swb w/68 front clip "GM Millenium corvette yellow" I use and accept Paypal |
04-08-2003, 01:39 AM | #3 |
No longer truckless
Join Date: Mar 2002
Location: Campbell, CA
Posts: 299
|
Here's a link to more pics. Here
I don't think there are any with the tailgate down, but I can get some soon. I am planning to go with a soft top in the winter & a bikini top in the summer. My hard top was kinda trashed & I hated all the noise inside the cab when it was on. It rattled & would kinda echo all the road noise around inside. The cage is a little too wide to fit the top on(by design) but I get the added benefit of a little extra head room. Plus the way it's bent, there's plenty of room for a back seat if I decide to put one in. |
04-08-2003, 09:27 AM | #4 |
Post Whore
Join Date: Feb 2000
Location: Rose Hill, KS, USA
Posts: 12,686
|
Looks awesome.
__________________
1970 Blazer with a 400 sbc and 4" lift 1980 Pontiac Trans Am, 455 Oldsmobile 2012 Kawasaki Concours 14 |
04-08-2003, 10:35 AM | #5 |
Account Suspended
Join Date: Mar 2001
Location: Virginia Beach, Va. U.S.A.
Posts: 15,320
|
Nice
|
04-08-2003, 11:53 AM | #6 |
Registered User
Join Date: Oct 2002
Location: Parksville, B.C. Canada
Posts: 637
|
Looks pretty skookum- nice job.
__________________
1969 G.M.C 3/4 Ton 920 (Canadian Version) 307 3 speed, currently apart 1998 Chevy 1/2 ton ex cab V-6 5 speed 1967 Chevy SWB - project truck; not started just yet |
04-08-2003, 01:25 PM | #7 |
Registered User
Join Date: Aug 2002
Location: Crittenden, KY
Posts: 1,965
|
Nice pool. I like the roll cage, but is your buddy going to finish up those welds? It'd look kinda bad when you paint it if the welds weren't done. Later.
Brandon |
04-08-2003, 01:27 PM | #8 |
Registered User
Join Date: Aug 2002
Location: Crittenden, KY
Posts: 1,965
|
Orrr. Maybe they are finished, in the pic of the top you just see a couple of tacks, Then in the later pics, there are none specifically of the welds, but they look done. My bad.
Brandon |
04-08-2003, 02:56 PM | #9 |
computer illiterate
Join Date: Jan 2001
Location: Des Moines, IA
Posts: 6,440
|
swee! nice cage.
__________________
72 2wd blazer 72 swb 4x4 |
04-08-2003, 02:56 PM | #10 |
Mike
Join Date: Jan 2003
Location: west chester pa
Posts: 2,473
|
You might want to put rollbar padding on the top bars.If not you get an annoying buzz when the soft top vibrates against the bar.I'm speaking with experence.I have a full cage and soft top.
__________________
70'c/10, 71 suburban4x4 402bb, 72suburban 4/6 drop, 72k/5 4x4 blazer 4" lift 35 tires |
04-08-2003, 03:10 PM | #11 |
No longer truckless
Join Date: Mar 2002
Location: Campbell, CA
Posts: 299
|
Thanks for the tip on the padding. I was planing to run it without padding, but if it makes noise, I guess I will have to put some on.
|
04-08-2003, 08:35 PM | #12 |
Registered User
Join Date: Apr 2003
Location: Edgewood New Mexico
Posts: 2,088
|
sweet cage
|
Bookmarks |
Thread Tools | |
Display Modes | |
|
|