![]() |
Register or Log In To remove these advertisements. |
|
|
![]() |
|
Thread Tools | Display Modes |
|
![]() |
#1 |
Registered User
Join Date: Jul 2007
Location: Fall River California
Posts: 2,026
|
Special tools to service 4X4 wheel bearings?
I want to repack the wheel bearings on the front of my 72 GMC 4X4, my manual mentions a special wrench to remove a retaining nut under the locking hub assembly. It says it's "difficult" without it. Am I going to need this wrench or is it possible to do without it? Any other helpful hints would be appreciated. I have done many wheel bearings but never on a 4X front axle. Thanks!
Posted via Mobile Device |
![]() |
![]() |
![]() |
#2 |
Real Projects never die
Join Date: Jan 2007
Location: Lawrence, kansas
Posts: 1,508
|
Re: Special tools to service 4X4 wheel bearings?
Yes, your gonna need it. Go to orileys or wherever and it should be on the shelf. Should have 4 prongs. The best tool to get is the one that has a steel ring around the 4 prongs, you'll pull the outside lock nut off, should be very tight. Then a cross shaped washer with pin holes in it, and then finally an innter nut with a pin towards the outside. Both nuts are the same size.
__________________
Ill put it this way, ive got a few lawn ornaments ![]() ![]() My name tag says Ryan KansasTwister On other forums
|
![]() |
![]() |
![]() |
#3 |
Real Projects never die
Join Date: Jan 2007
Location: Lawrence, kansas
Posts: 1,508
|
Re: Special tools to service 4X4 wheel bearings?
![]()
__________________
Ill put it this way, ive got a few lawn ornaments ![]() ![]() My name tag says Ryan KansasTwister On other forums
|
![]() |
![]() |
![]() |
#4 | |
just can't cover up my redneck
Join Date: May 2004
Location: Columbus OH
Posts: 11,414
|
Re: Special tools to service 4X4 wheel bearings?
Technically the ones with the 4 tabs sticking out are from a truck with automatic hubs, so don't be surprised if they aren't there. The lock ring should simply be round with one tab on the inner diameter, which keys it to the slot in the spindle.
It doesn't hurt anything if they are there, they just don't do anything w/o the auto hubs. Be very carefull when you put the lock ring back together. The pin from the inner nut has to fit into one of the holes in the washer, be sure that is sits flat over the pin. If it does not fit the first time, turn the washer over, the holes are off-set from the inner tab. If it still doesn't fit, loosen the nut very slightly and try again. Remember that the outer nut will add a bit more pressure as it takes up the slack in the thread fit.
__________________
You can review the site's rules here. Quote:
Bad planning on your part does not necessarily constitute an instant emergency on my part.... The great thing about being a pessimist is that you are either pleasantly surprised or right. ![]() |
|
![]() |
![]() |
![]() |
#5 |
Registered User
Join Date: Jul 2007
Location: Fall River California
Posts: 2,026
|
![]()
Thanks everyone! Good info! I went to NAPA and picked up the socket, I'm going to have to use my own judgment instead of a torque wrench!
Thanks for the help! Aaron Posted via Mobile Device |
![]() |
![]() |
![]() |
#6 |
Registered User
Join Date: Jul 2007
Location: Fall River California
Posts: 2,026
|
Re: Special tools to service 4X4 wheel bearings?
I was thinking of doing this today but I didnt think about picking up new seals and the parts store is closed, is it possible to reuse the old seals or should I put it off till I buy new seals? It sucks living in a small town!
Posted via Mobile Device |
![]() |
![]() |
![]() |
#7 |
Registered User
Join Date: Sep 2010
Location: ND
Posts: 520
|
Re: Special tools to service 4X4 wheel bearings?
Yes you need the special socket. The nuts have 4 notches that are about impossible to take off with a punch if the outer nut is as tight as it should be and besides the nut would get all beat up and the socket wouldnt work on it after it was beat up anyways.
__________________
Name: Les ---------------------- Couple 80s Couple 70s One 68 ![]() |
![]() |
![]() |
![]() |
#8 |
Kid's Mechanic
Join Date: Nov 2006
Location: Kansas City
Posts: 8,241
|
Re: Special tools to service 4X4 wheel bearings?
Wait on the fresh Seals , Only thing worse than doing a dirty job is having to do it twice .
|
![]() |
![]() |
![]() |
#9 |
Registered User
Join Date: Jul 2007
Location: Fall River California
Posts: 2,026
|
Re: Special tools to service 4X4 wheel bearings?
Glad I waited till today, My wheel bearings were trash! So was the seal. The special socket was well worth the ten bucks I paid, it would have been horrible setting up the right tension on the bearings without it! Thanks again for all the advice everyone, it made the job that much easier.
Posted via Mobile Device |
![]() |
![]() |
![]() |
#10 |
Registered User
Join Date: Sep 2011
Location: San Jose, California
Posts: 784
|
Re: Special tools to service 4X4 wheel bearings?
What's the brand and part number of the special socket?
Thanks |
![]() |
![]() |
![]() |
Bookmarks |
Thread Tools | |
Display Modes | |
|
|