Register or Log In To remove these advertisements. |
|
|
|
Thread Tools | Display Modes |
|
03-24-2012, 09:52 AM | #1 |
Registered User
Join Date: Nov 2011
Location: So. Calif
Posts: 305
|
Replacing freeze plugs,painting engine area..
On my 74 C10, gonna have all my freeze plugs replaced, and the following gaskets/seals replaced-front main seal and rear seal,valve cover gaskets,rebuild kit for my Edlebrock carb, and since my motor is being pulled out for the freeze plug replacing, its gonna get degreased and painted. The 74's originally had the motors painted reddish orange correct? Was thinking about painting it black since the fenderwels and other areas are already painted black. And as time goes by little by little i will be adding and replacing things and getting them in chrome so they will stand out against the black. But I really like the look of the reddish color on the motor when done right. How about some pics of the motors some of you all have so I can check out how they look in different colors for those of you that have theirs painted.
|
03-24-2012, 10:51 AM | #2 |
Registered User
Join Date: Oct 2010
Location: Frankston Tx
Posts: 151
|
Re: Replacing freeze plugs,painting engine area..
not mine but cool
__________________
all i know is that its going to be orange |
03-24-2012, 11:36 AM | #3 |
Registered User
Join Date: Nov 2011
Location: So. Calif
Posts: 305
|
Re: Replacing freeze plugs,painting engine area..
Forgot to mentiom, which brands/paints hold up? Thanks.
|
03-24-2012, 01:53 PM | #4 |
GM Addicted
Join Date: Jan 2009
Location: Visalia, Ca
Posts: 2,294
|
Re: Replacing freeze plugs,painting engine area..
Heres mine man. On my 350 i went with all black. Its duplicolor engine paint it stands up well, i dont paint over freeze plugs like the natural look of them. It has an edelbrock endurashine intake just need the endurashine carb. Its not really clean under hood but its something.
__________________
..Mac’s Garage.. 73 GMC, 54 Caddy, 2010 Silverado, 68 C10 RIP DAd My 73 GMC Truck Build Pic 2010 Silverado 4/6 on 24s IG:MacsGarage |
03-24-2012, 01:55 PM | #5 |
GM Addicted
Join Date: Jan 2009
Location: Visalia, Ca
Posts: 2,294
|
Re: Replacing freeze plugs,painting engine area..
Heres some of the stock 305 when it was fully rebuilt with all smog equipment and the 2 barrel carb. Then changed intakes and carbs. On the 305 i painted the block black and the heads the cast aluminum color. But the silver didnt hold up as well as the black. They also sell a clear that might have helped it. Just a few pics man
__________________
..Mac’s Garage.. 73 GMC, 54 Caddy, 2010 Silverado, 68 C10 RIP DAd My 73 GMC Truck Build Pic 2010 Silverado 4/6 on 24s IG:MacsGarage |
03-24-2012, 09:53 PM | #6 |
Registered User
Join Date: Nov 2011
Location: So. Calif
Posts: 305
|
Re: Replacing freeze plugs,painting engine area..
Thank guys, keep the pics coming.
|
03-25-2012, 02:55 AM | #7 |
Registered User
Join Date: Oct 2003
Location: OC CA
Posts: 1,374
|
Re: Replacing freeze plugs,painting engine area..
Well, I'll have to oblige...
This engine came from a swap meet - very cheap. It is 3970010 block circa 1971. My machinist indicated that this is probably one of the last higher Nickel content blocks GM produced. To cut machining cost GM reduced Nickel levels in mid 70's into the 80's. Engine is mounted on the stand - starting the tear down. Lots of oil crud indicating infrequent oil changes. and this is a result of infrequent oil changes - #3 connecting rod bearings has spun rendering Crankshaft unrepairable! The 4-bolt main block however is in good shape along with Nodular main caps. Skipping ahead.. Painting the Engine (350SBC) - POR-15 Engine Enamel (Chevy Orange) Mounted on the test stand for cam break-in Just dropped in in its new home. //RF
__________________
"The Beast" 1975 Chevrolet C20 longbed 350/700R4! with 3inch body lift Dual Flowmasters Super 40's! TBI retrofit completed (2007-07-29) New 383CID (+030) 08-304-8 9.5:1CR x36,005 (2012-12-17) |
03-24-2012, 11:38 PM | #8 |
Registered User
Join Date: Oct 2003
Location: OC CA
Posts: 1,374
|
Re: Replacing freeze plugs,painting engine area..
I had good results using POR-15 Engine Enamel. One quart (black or chevy orange) is more than enough to do one engine. Stuff goes on with a brush which allows for a greater control vs. rattle can. Once paint dries it maintains that wet look.
For '74 model year truck it you should use chevy orange, but as my Elmer used to say engines are color blind. //RF
__________________
"The Beast" 1975 Chevrolet C20 longbed 350/700R4! with 3inch body lift Dual Flowmasters Super 40's! TBI retrofit completed (2007-07-29) New 383CID (+030) 08-304-8 9.5:1CR x36,005 (2012-12-17) |
03-25-2012, 12:47 PM | #10 |
Registered User
Join Date: Jul 2009
Location: washington
Posts: 4,178
|
Re: Replacing freeze plugs,painting engine area..
I like the contrast of the orange black and polished aluminum Posted via Mobile Device
__________________
377 sbc thumpr cam autogear m23 muncie 3:73 Detroit trutrac 3''spintech prostreet mufflers xpipe 1 3/4 headers build thread !http://67-72chevytrucks.com/vboard/s...d.php?t=577217 Iroc gauge threadhttp://67-72chevytrucks.com/vboard/s...d.php?t=554511 |
03-25-2012, 05:07 PM | #11 |
Registered User
Join Date: Nov 2011
Location: So. Calif
Posts: 305
|
Re: Replacing freeze plugs,painting engine area..
Man all of yours look cool man! I hope to be having my friend/mechanic start this week on mine.
|
Bookmarks |
Thread Tools | |
Display Modes | |
|
|