98 Vortec 350. Fuel pump help! - The 1947 - Present Chevrolet & GMC Truck Message Board Network

HEISEL · 04-05-2012, 10:32 PM

Hi all, so I have a 98 Vortec 350 that a had rebuilt back to stock. Except it has a edelbrock carb intake. Because im going that way. So my plan was to put a mechanical fuel pump on it because it has provisions for one. My question is can I do this? I was told that I needed a special pump rod for this? Because its a roller cam I guess? O ya it's going in my 72 k10 swb. Is this true? Any suggestions? Thanks.
Posted via Mobile Device

61K10 · 04-06-2012, 12:49 PM

you can get one from jegs or summit that has a bronze tip $21 or a roller tip $100+ roller cams are steel not iron and i guess the lobes aren't heat treated. somebody here knows the story. i ran a bronze tip one with a roller years ago. does chevy make a stock one?

1972CST · 04-07-2012, 09:27 PM

Some roller cams don't have a lobe for mech. fuel pump.
Posted via Mobile Device

clinebarger · 04-07-2012, 09:58 PM

Ive never seen a production 98 vortec block have the hole for the pump rod.
Like 1972CST said the Factory Production cam WILL NOT have the lobe

67c10rustbuket · 04-07-2012, 11:14 PM

The mount is still cast on the block but there is no hole for the pump push rod. If you are rebuilding a block the hole can be drilled but not on a used install because you risk metal shavings getting into the block. I think that factory cam does not have a lobe for the mech pump. The easiest way would be to go to the parts store and get a universal electronic fuel pump for a carb. like this from autozone.

http://www.autozone.com/autozone/par...1_173883_4967_

Shyguy · 04-08-2012, 09:13 AM

If you go with an electric fuel pump it is a good idea to also put a fuel pressure regulator in since the Edelbrock carbs like a constant pressure, I can not remember the exact number but I think it is 5 pounds.

Also the fuel pump should be mounted as close to the tank as possible.

rayfinseats · 04-09-2012, 12:19 AM

Go with an electric pump. You can get a cheap one since you only need 5-6 pounds of pressure. It helps with vapor lock if running high compression or headers. Easier to replace too. I had four different kinds of pumps on my 68 camaro before I went electric.

04-05-2012, 10:32 PM	#1
HEISEL Registered User Join Date: Feb 2011 Location: Blue springs, mo Posts: 56	98 Vortec 350. Fuel pump help! Hi all, so I have a 98 Vortec 350 that a had rebuilt back to stock. Except it has a edelbrock carb intake. Because im going that way. So my plan was to put a mechanical fuel pump on it because it has provisions for one. My question is can I do this? I was told that I needed a special pump rod for this? Because its a roller cam I guess? O ya it's going in my 72 k10 swb. Is this true? Any suggestions? Thanks. Posted via Mobile Device __________________ 1972 k/10 4x4 swb 2011 camaro SS/RS M6

04-06-2012, 12:49 PM	#2
61K10 Registered User Join Date: Feb 2012 Location: pleasant valley--placerville ca Posts: 3,039	Re: 98 Vortec 350. Fuel pump help! you can get one from jegs or summit that has a bronze tip $21 or a roller tip $100+ roller cams are steel not iron and i guess the lobes aren't heat treated. somebody here knows the story. i ran a bronze tip one with a roller years ago. does chevy make a stock one? __________________ 1961 chevy K10 my build is------------61K10 build

04-07-2012, 09:27 PM	#3
1972CST Registered User Join Date: Mar 2008 Location: Concord NC Posts: 511	Re: 98 Vortec 350. Fuel pump help! Some roller cams don't have a lobe for mech. fuel pump. Posted via Mobile Device

04-07-2012, 09:58 PM	#4
clinebarger Senior Member Join Date: May 2009 Location: Fort Worth, TX Posts: 6,370	Re: 98 Vortec 350. Fuel pump help! Ive never seen a production 98 vortec block have the hole for the pump rod. Like 1972CST said the Factory Production cam WILL NOT have the lobe

04-07-2012, 11:14 PM	#5
67c10rustbuket Registered User Join Date: Apr 2011 Location: Mustang, Oklahoma Posts: 2,806	Re: 98 Vortec 350. Fuel pump help! The mount is still cast on the block but there is no hole for the pump push rod. If you are rebuilding a block the hole can be drilled but not on a used install because you risk metal shavings getting into the block. I think that factory cam does not have a lobe for the mech pump. The easiest way would be to go to the parts store and get a universal electronic fuel pump for a carb. like this from autozone. http://www.autozone.com/autozone/par...1_173883_4967_ __________________ Dan <---(my name) 67 SWB C10 project "GEORGIA"-59 Brookwood 2dr wag...Next project-03 Tahoe 4x4 5.3 family ride-07 Hondur Accord, commuter car

04-08-2012, 09:13 AM	#6
Shyguy Junior Member Join Date: Dec 2006 Location: Southeast Missouri Posts: 2,436	Re: 98 Vortec 350. Fuel pump help! If you go with an electric fuel pump it is a good idea to also put a fuel pressure regulator in since the Edelbrock carbs like a constant pressure, I can not remember the exact number but I think it is 5 pounds. Also the fuel pump should be mounted as close to the tank as possible. __________________ '67 Chevy C-20 short stepper - build complete, 454/SM-465. '75 C-30 Single Cab DRW-350 small block/NP-435. '77 GMC-6500 Dump Truck, 427 Tall Deck. '92 GMC K-3500 Duallie, 454/4L80E.

04-09-2012, 12:19 AM	#7
rayfinseats Registered User Join Date: Dec 2010 Location: sioux city, iowa Posts: 619	Re: 98 Vortec 350. Fuel pump help! Go with an electric pump. You can get a cheap one since you only need 5-6 pounds of pressure. It helps with vapor lock if running high compression or headers. Easier to replace too. I had four different kinds of pumps on my 68 camaro before I went electric.

Thread Tools
Show Printable Version Email this Page
Display Modes
Switch to Linear Mode Hybrid Mode Switch to Threaded Mode



Register or Log In To remove these advertisements.

Register or Log In To remove these advertisements.