The 1947 - Present Chevrolet & GMC Truck Message Board Network







Register or Log In To remove these advertisements.

Go Back   The 1947 - Present Chevrolet & GMC Truck Message Board Network > 47 - Current classic GM Trucks > The 1967 - 1972 Chevrolet & GMC Pickups Message Board

Web 67-72chevytrucks.com


Reply
 
Thread Tools Display Modes
Old 08-18-2012, 04:20 PM   #1
TheSeeker
Registered User
 
Join Date: Dec 2009
Location: Glendale, AZ
Posts: 337
250 IL6 to SBC swap

Hey all, I recently developed a pretty bad low end knock in my stock 250. I want to pull the motor and swap out to a small block. I am currently starting with a bone stock 6 cyl truck. If anyone has done this swap, can you tell me what I would need to complete it start to finish? Kind of a parts list cheat sheet if you will, (Fuel line changes? Cross member? Can I use the 3 speed manual I have? etc.) I am sure I can complete the project ina few weeks with good buddies and good brews, but dont want to go in unprepared. Thanks in advance for any insight!


p.s. I know a lot of folks like the old 6 banger, I did too, I think it gives the truck character and was cool to see at shows. However, I daily drive this truck, and tracking down parts, pullies, brackets etc to fix it/rebuild it and add air and ps, is a huge pain. Anyone who has owned one of these 6's will tell you the parts supply and price is a huge con to owning one instead of the sbc. :/
TheSeeker is offline   Reply With Quote
Old 08-18-2012, 04:50 PM   #2
PanelDeland
I am a Referee of life.
 
PanelDeland's Avatar
 
Join Date: Jun 2000
Location: Greensboro N.C.
Posts: 13,992
Re: 250 IL6 to SBC swap

I'm one who loves the 6 but if I had to replace an engine,I would probably save the money by going to a350 also.The towers and placement are different in the V-8 truck(BB and SB also).The tranny works,IIRC so does the bellhousing and clutch but you will need a flywheel.The bellcrank and mounts for it are different for the V-8 clutch.I'm sure that's not all but someone will probably point out my shortcomings.
__________________
The 47-present Chevrolet and GMC Truck Message Board Network,it's owners,moderators,members,and associates of any type should not be held responsible for my opinion.
You can't fix stupid,not even with duct tape.
"My appearance is due to the fact that "GOD" does punish you for having too much fun!"
Barrett-Jackson has perfected alchemy,they make rust into gold!
"You can lead a horse to water but you can't saddle a duck"
"Cleverly disguised as a 'Responsible Adult'
"Sometimes your Knight in shining armor is just a retard in tinfoil"
PanelDeland is offline   Reply With Quote
Old 08-18-2012, 08:59 PM   #3
68gmsee
Active Member
 
68gmsee's Avatar
 
Join Date: Jul 2007
Location: Centrally located between Houston, Austin and Waco. BCS area.
Posts: 7,947
Re: 250 IL6 to SBC swap

ttt

It's been many years since I converted mine but I remember the drive shaft was different in length also. I used a complete 350 engine and 350 transmission off a 75 Impala.

My advice is to see if you can find an old clunker 68-72 if you can otherwise it's going to take some time to locate what you need. Be sure and check this site's parts for sale section, ebay and even Craigs lists in your state for cities near you.
__________________
68 GMC 250/3 speed Saginaw p/b p/s
69 Chevy 350/350 currently in pieces still lookin for a cab
06 Trailblazer
I just want a vehicle that I can work on, that won't talk to me, leave error msgs or keep track of how I drive...
68gmsee is offline   Reply With Quote
Old 08-18-2012, 09:32 PM   #4
pritch
Registered User
 
pritch's Avatar
 
Join Date: Mar 2004
Location: Hoytsville, Utah
Posts: 3,365
Re: 250 IL6 to SBC swap

Quote:
Originally Posted by 68gmsee View Post
ttt

It's been many years since I converted mine but I remember the drive shaft was different in length also. I used a complete 350 engine and 350 transmission off a 75 Impala.
If you use the original 3 speed, the drive shaft should work. The transmission shouldn't have to move unless you mount the V-thingy back in the L6 position, which some guys do.
__________________
'68 Panel
Project Boogie Chillin'
'68 C-10
Ol' Green
pritch is offline   Reply With Quote
Old 08-19-2012, 02:32 AM   #5
TheSeeker
Registered User
 
Join Date: Dec 2009
Location: Glendale, AZ
Posts: 337
Re: 250 IL6 to SBC swap

OK. Weekend got away from me so I am just gettin back on this now. Thanks for the help guys. Anybody else have any pointers?
TheSeeker is offline   Reply With Quote
Reply

Bookmarks

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -4. The time now is 02:51 AM.


Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2024, vBulletin Solutions Inc.
Copyright 1997-2022 67-72chevytrucks.com