The 1947 - Present Chevrolet & GMC Truck Message Board Network







Register or Log In To remove these advertisements.

Go Back   The 1947 - Present Chevrolet & GMC Truck Message Board Network > 47 - Current classic GM Trucks > The 1967 - 1972 Chevrolet & GMC Pickups Message Board

Web 67-72chevytrucks.com


Reply
 
Thread Tools Display Modes
Old 10-20-2012, 08:51 PM   #1
CNEPACE
Registered User
 
Join Date: Oct 2012
Location: Ontario, Canada
Posts: 7
Trying to reduce body lift but cant?

I recently acquired a 1969 K2500 fleetside 4 x 4. It has a 454 big block with a NP 208 transfer case and turbo 400 in it. The truck currently has a 4 inch body lift on it and a 4 inch suspension lift. My plan was to increase the suspension lift, and decrease the body lift. While I was under the truck today checking clearances I noticed the transfer case was only 1 inch below the cab. The engine and transfer case are all mounted properly but I am confused as to why there is only 1 inch of clearance over the transfer case with a 4 inch body lift. Has anybody on this combination (454/NP208)? Is it normal to have to lift the body to clear the transfer case?
Posted via Mobile Device
CNEPACE is offline   Reply With Quote
Old 10-20-2012, 08:53 PM   #2
71swb4x4
Senior Member
 
71swb4x4's Avatar
 
Join Date: Nov 2003
Location: Brookings, SD
Posts: 10,497
Re: Trying to reduce body lift but cant?

Is it a high hump cab or low hump? It sounds like a 2wd (low hump) cab on your truck.
If that's the case you can cut the low hump out, and bolt a high hump in.

If that's not it than it probably has something to do with the transfer case. The NP208 wasn't stock in this body style.
__________________
Some people are like slinkies, they aren't good for anything, but you can't help but smile when you see one tumble down the stairs.
71swb4x4 is offline   Reply With Quote
Old 10-20-2012, 08:57 PM   #3
CNEPACE
Registered User
 
Join Date: Oct 2012
Location: Ontario, Canada
Posts: 7
Re: Trying to reduce body lift but cant?

How can I tell if it is a low or high hump? Does anybody know the measurements?
Posted via Mobile Device
CNEPACE is offline   Reply With Quote
Old 10-20-2012, 09:04 PM   #4
CNEPACE
Registered User
 
Join Date: Oct 2012
Location: Ontario, Canada
Posts: 7
Re: Trying to reduce body lift but cant?

I did some reading on the hump. My question is does the hump make for transmission clearance or also the transfer case clearance?
Posted via Mobile Device
CNEPACE is offline   Reply With Quote
Old 10-20-2012, 09:12 PM   #5
special-K
Special Order

 
special-K's Avatar
 
Join Date: Nov 2004
Location: Mt Airy, MD
Posts: 85,851
Re: Trying to reduce body lift but cant?

Both. The high hump was used for 4spd transmission and all 4wd. They bolt in and the low hump aren't.
__________________
"BUILDING A BETTER WAY TO SERVE THE USA"......67/72......"The New Breed"

GMC '67 C1500 Wideside Super Custom SWB: 327/M22/3.42 posi.........."The '67" (project)
GMC '72 K2500 Wideside Sierra Custom Camper: 350/TH350/4.10 Power-Lok..."The '72" (rolling)
Tim

"Don't call me a redneck. I'm a rough cut country gentleman"

R.I.P. ~ East Side Low Life ~ El Jay ~ 72BLUZ ~ Fasteddie69 ~ Ron586 ~ 67ChevyRedneck ~ Grumpy Old Man ~
special-K is offline   Reply With Quote
Old 10-21-2012, 10:06 AM   #6
71swb4x4
Senior Member
 
71swb4x4's Avatar
 
Join Date: Nov 2003
Location: Brookings, SD
Posts: 10,497
Re: Trying to reduce body lift but cant?

If you can't eyeball the low hump vs high hump just pull the carpet back. As Tim says the low hump is stamped into the floorpan, it is part of the pan. The high hump bolts onto the florr pan.
__________________
Some people are like slinkies, they aren't good for anything, but you can't help but smile when you see one tumble down the stairs.
71swb4x4 is offline   Reply With Quote
Old 10-21-2012, 11:56 AM   #7
CNEPACE
Registered User
 
Join Date: Oct 2012
Location: Ontario, Canada
Posts: 7
Re: Trying to reduce body lift but cant?

Confirmed it is a 2wd cab. At least I know what the problem is. I am going to keep the body lift as I dont feel like cutting it up right now!
CNEPACE is offline   Reply With Quote
Reply

Bookmarks

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -4. The time now is 01:18 AM.


Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2024, vBulletin Solutions Inc.
Copyright 1997-2022 67-72chevytrucks.com