![]() |
Register or Log In To remove these advertisements. |
|
|
![]() |
|
Thread Tools | Display Modes |
|
![]() |
#1 |
Registered User
Join Date: Sep 2011
Location: rosamond ca
Posts: 130
|
Fixing Broken Pot metal Heater Controls.
Being the Cheap ass Guy that I am,,my defrost lever on the heater controls broke,,it also operates the Vac switch for the heater controls,,So instead of Buying a Entire New aftermarket unit,,Decided to rip it apart and see if I could fix it! After A few fabrications,,and using a part of the bed sheetmetal I cut out for the gas tank install,,my lever is working great and stronger than stock!
![]()
__________________
edited by staff |
![]() |
![]() |
![]() |
#2 | ||
"I ain't nobody, dork."
Join Date: Sep 2007
Location: Whidbey Island, Washington
Posts: 8,936
|
Re: Fixing Broken Pot metal Heater Controls.
Pretty slick!
![]() Gary
__________________
'cuz chicks dig scars... My 1972 GMC 1500 Super Custom (Creeping Death) "long term" build thread. The Rebuild of Creeping Death after the wreck Quote:
Quote:
|
||
![]() |
![]() |
![]() |
#3 |
Registered User
Join Date: Sep 2011
Location: rosamond ca
Posts: 130
|
Re: Fixing Broken Pot metal Heater Controls.
I Tried JB weld first! broke the first time I tried to use it,,Oh Well!
__________________
edited by staff |
![]() |
![]() |
![]() |
#4 |
Registered User
![]() Join Date: Jan 2006
Location: Peyton, CO
Posts: 448
|
Re: Fixing Broken Pot metal Heater Controls.
Buying a complete control unit can be pricy. LMC prices them at $169.95 for with A/C and $129.95 w/o A/C.
But, you can buy a kit for $29.95 and do a rebuild on your existing Heat and A/C control. It's worth considering... http://www.lmctruck.com/icatalog/cb/full.aspx?Page=100
__________________
don "The DRBMan" 2014 Audi A4 (The Wife's Daily Driver) 2017 HD Ultra (The Cruiser) 2003 HD Fatboy (The Ride) 2001 Chevy Suburban (Another back up!!) For the first time in forever, not a single 67-72 Chevy truck, Blazer, or Suburban on the property! Basically retired and getting the new Motorhome ready for some traveling. Doing a bit of work on the house getting it ready to sell! LOL!! |
![]() |
![]() |
![]() |
#5 |
Registered User
Join Date: Nov 2010
Location: Carlsbad, CA
Posts: 1,584
|
Re: Fixing Broken Pot metal Heater Controls.
Impressive repair.
I was gonna fix my busted one, too until I found that I could get the lever alone for about six bucks + S&H (LMC sells that lever alone PN 30-2687).
__________________
- Jim - My Daily Driver is a 1969 Chevrolet Custom/20 Fleetside 350/TH400/Eaton H052 4.10 and its Project thread is here http://67-72chevytrucks.com/vboard/s...d.php?t=456911 |
![]() |
![]() |
![]() |
#6 | |
Account Suspended
Join Date: Oct 2012
Location: Salt Lake City, Utah
Posts: 3,331
|
Re: Fixing Broken Pot metal Heater Controls.
Quote:
Posted via Mobile Device |
|
![]() |
![]() |
![]() |
#7 |
I am a Referee of life.
Join Date: Jun 2000
Location: Greensboro N.C.
Posts: 13,993
|
Re: Fixing Broken Pot metal Heater Controls.
Don't forget to clean/lube the cables.That will go a long way towards making them last.
__________________
The 47-present Chevrolet and GMC Truck Message Board Network,it's owners,moderators,members,and associates of any type should not be held responsible for my opinion. You can't fix stupid,not even with duct tape. "My appearance is due to the fact that "GOD" does punish you for having too much fun!" Barrett-Jackson has perfected alchemy,they make rust into gold! "You can lead a horse to water but you can't saddle a duck" "Cleverly disguised as a 'Responsible Adult' "Sometimes your Knight in shining armor is just a retard in tinfoil" |
![]() |
![]() |
![]() |
#8 |
Registered User
Join Date: Sep 2011
Location: rosamond ca
Posts: 130
|
Re: Fixing Broken Pot metal Heater Controls.
My junk yard did not have any A/C units,,Did not know you could buy the individual levers?? I called LMC and they told me they only sold the entire Unit? Tried to buy some other parts seperate like the Vac Head control and they said I need to buy the entire Unit?? What Gives?
__________________
edited by staff |
![]() |
![]() |
![]() |
#9 |
Registered User
Join Date: Jan 2011
Location: Townsend MT
Posts: 1,725
|
Re: Fixing Broken Pot metal Heater Controls.
I would have JB welded it and bolted it after the JB weld broke. But that is just the way I am.
Are the lever made of aluminum? If so, I may try to weld mine and then plate it. |
![]() |
![]() |
![]() |
#10 |
Registered User
Join Date: Mar 2012
Location: Boulder, CO
Posts: 350
|
Re: Fixing Broken Pot metal Heater Controls.
I've been pondering a cheap 'n' easy fix for the top lever on the '71 Cheyenne. I've got it jammed on full blast, gimme heat stroke right now. When the weather gets nice here in Colorado, I'll pull it out and get creative.
As a side note, kinda related- I've used strands of steel wool mixed in with the JB Weld, for high-strength items to fix items I am too cheap or unwilling to search for. Works great on plastic hubs on lawnmower drive wheels! I wouldn't use it in this situation, though- too much concentrated side-loading. Posted via Mobile Device |
![]() |
![]() |
![]() |
#11 |
Registered User
Join Date: May 2009
Location: Goldsboro NC
Posts: 151
|
Re: Fixing Broken Pot metal Heater Controls.
|
![]() |
![]() |
![]() |
#12 |
Registered User
Join Date: Apr 2012
Location: San Jose, CA
Posts: 69
|
Re: Fixing Broken Pot metal Heater Controls.
I also bought the lever from LMC. But in looking at the unit, how do I get it apart to replace the part? It looks as if it's a solid piece. What is it I'm not seeing?
Last edited by nolimitssjca; 04-08-2013 at 11:21 PM. |
![]() |
![]() |
![]() |
Bookmarks |
Thread Tools | |
Display Modes | |
|
|