TX 88 suburban part out

[Lone_Star]

I have an '88 suburban that I am parting out, it is/was a donor for another truck. I have or will be pulling the front fenders, front bumper, front doors, hood, cowl. transmission, engine TBI harness and computer, guages, dash harness, and interior heat/air box. I have also removed the front kick panels. All else is for sale, if not listed below, ask. This is my first part-out, so if my prices are out of line, let me know, I am sure we can work something out. I would rather not ship large items, but if we can work out a shipment method/cost, then we can make it happen. Parts prices do not include shipping.

On to the photos;
The 'burb as it sits now;


Parts that I have pulled and ready:
'88 grille and headlight bezels - $50


'89-91 grille - aftermarket, bezels have chrome lifting but center section is good shape - $30


Hooker competition headers - p/n 2451 - they are listed as car headers, but fit with no issues, have O2 sensor bung on left side collector - $60

[Lone_Star]

More parts;
Suburban fuel tank - no pump but has sending unit - $40


'82 truck 16gal, driver side tank - with straps/mounts, sending unit is bad - $50


Suburban door panels - fronts still on truck but will remove, rear doors I have, 1 is busted, ask for photos - $20 each



Gauge bezel - good shape, uncut - $SOLD

The dash pad is cracked, but the vent trim piece is good, the bucket seats are a bit rough but can be saved, the middle seat is in good shape, seat belts are there, interior trim, rear A/C, engine, core support, etc, all available.

I will do my best to answer questions and get shipping quotes as quickly as I can.

Bryan

[83GMCK2500]

Manual or auto?

[Lone_Star]

Originally Posted by 83GMCK2500

Manual or auto?

It is an auto trans, but I am keeping the trans, torque converter, and cooler lines.

Bryan

[83GMCK2500]

Originally Posted by Lone_Star

It is an auto trans, but I am keeping the trans, torque converter, and cooler lines.

Bryan

Thank you. I am actually looking for a hydro clutch pedal assembly. Good luck with parting it.

[Lone_Star]

UATahoe - I have you first in line on the gauge bezel. Any particular area that you want close-up photos of?

[MDc10]

Do you.have the pull strap covers and mounting hardware?
Posted via Mobile Device

[Lone_Star]

Originally Posted by MDc10

Do you.have the pull strap covers and mounting hardware?
Posted via Mobile Device

MDc10 - I only have the pull strap on the drivers door, no others, and no covers.

[UATahoe]

How is the brushed aluminum? Any fading, cracks, or other damage? Interested in the bezel for sure. Any chance you could post up some close up pictures to show the condition of the brushed aluminum overlay? Thanks!

[Lone_Star]

UATahoe - The gauge bezel is in great shape. I will take photos of it this evening and post up.

Bryan

[UATahoe]

Thanks Bryan! Will be sure to check back, and if it looks good i will take it so put me first in line. Thanks again!

[77ChevySharkBite]

how much did you want for the tbi?

[Lone_Star]

Originally Posted by 77ChevySharkBite

how much did you want for the tbi?

The complete TBI system was removed and used on another truck. I do have a throttle body left over if you are looking for one.

[77ChevySharkBite]

Originally Posted by Lone_Star

The complete TBI system was removed and used on another truck. I do have a throttle body left over if you are looking for one.

It's okay thanks though, I was trying to get the whole tbi system.

[ramz]

front bumper guards ? local pick up

[Lone_Star]

Originally Posted by ramz

front bumper guards ? local pick up

How does $40 sound?
I will see if I can pull them tonight and get some pics.

[ramz]

Originally Posted by Lone_Star

How does $40 sound?
I will see if I can pull them tonight and get some pics.

Sounds good.

[UATahoe]

Just wanted some pictures showing the brushed aluminum finish and wanted to make sure there were no cracks. I know sometimes the aluminum fades or spots up.

[Lone_Star]

Originally Posted by UATahoe

Just wanted some pictures showing the brushed aluminum finish and wanted to make sure there were no cracks. I know sometimes the aluminum fades or spots up.

The brushed aluminum looks good, no damage or fading that I can see. The strip between the vent controls and radio is a bit darker than the rest, but figure it is due to wear. May be able to clean it and not be able to tell. No cracks in the plastic around the mounting holes.

[Liddy71]

how is the 88 grille stuff any cracks pr mounting tabs broke ship to 25570

[Lone_Star]

Originally Posted by Liddy71

how is the 88 grille stuff any cracks pr mounting tabs broke ship to 25570

I will check the grille tonight to be sure, but don't remember any cracks or broken tabs. I also have the stainless trim that is mounted to the fenders/hood/valance if you need that too.

[Lone_Star]

Ramz - I pulled the bumper guards tonight. They are straight and good shape. Light surface rust on the backside, a couple of small rust spots on the front; one at the bottom below the pad, the other next to the pad. Light scuffs on the pads.

[ramz]

Originally Posted by Lone_Star

Ramz - I pulled the bumper guards tonight. They are straight and good shape. Light surface rust on the backside, a couple of small rust spots on the front; one at the bottom below the pad, the other next to the pad. Light scuffs on the pads.

Attachment 1055499

Attachment 1055500

Attachment 1055501

Attachment 1055502

Attachment 1055503

Ok. Where you located in Ft Worth

[Lone_Star]

Originally Posted by ramz

Ok. Where you located in Ft Worth

PM sent

[Lone_Star]

Originally Posted by Liddy71

how is the 88 grille stuff any cracks pr mounting tabs broke ship to 25570

I checked the grille, no broken tabs or cracks. The painted band has some peeling near the bowtie, and the stainless bands have a couple small dings.

Grille - $50 + shipping - $15 = $65 total via UPS Ground.