Tail shaft vs yoke - The 1947 - Present Chevrolet & GMC Truck Message Board Network

Hx16457 · 02-08-2013, 10:55 PM

Tell me;
Does anyone know how much of the yoke has to reach inside the tail shaft to get a good seal and contact enough of the actual tail shaft to get good surface area contact and good torque?
Note: I am in need of this information as it is compared to a,
350 V8, mounted in the front mounted position, with a th350, matched with a 1972 dif. With 3.73gears...
Posted via Mobile Device

Idaho64GMC · 02-08-2013, 11:09 PM

from what I've read there should be less than an inch of the yoke exposed, so bottom the yoke out and pull it out to 3/4 or an inch exposed and you should be good

Tx Firefighter · 02-09-2013, 07:33 AM

Ideally, the yoke should be bottomed, then pulled out 3/4 of an inch. Again, that's ideal and what my driveshaft shop uses for building one. You'll still be fine if it's 1/2 or even up near 1 inch though.

Hx16457 · 02-09-2013, 07:54 AM

Okay thx for the replays.

I need a longer shaft, then. Mine is pulled out approx. 2 or more inches from the tail shaft...
It sounds like I need one at least 1.25" longer to get me closer to the tail piece.
Posted via Mobile Device

Hx16457 · 02-09-2013, 01:23 PM

Anybody else running a similar set-up, with a one piece that could tell me the donor they used?
Posted via Mobile Device

Hx16457 · 02-09-2013, 08:15 PM

Bump.... Anyone?
Posted via Mobile Device

61K10 · 02-10-2013, 01:25 PM

they do make different length yoke's i think. speedway catalog? might just work.

Tx Firefighter · 02-10-2013, 01:44 PM

No one is going to be able to give any recommendation on a donor driveshaft without knowing what length transmission your th350 (there are 3 different length th350 trans) is and whether your truck is long or short wheelbase.
Posted via Mobile Device

tincan1966 · 02-10-2013, 01:50 PM

I noted in the posting that the engine is in the forward mounting location? Why not move it back to where a V8 normally mounts and solve the problem?

Are you running a 2 piece drive shaft? If so, then the engagement of the yoke isn't nearly as critical,as long as you have about 75% engaged, because you have no risk of it bottoming out during suspension compression.
Excuse me if I am missing something.

Hx16457 · 02-10-2013, 07:14 PM

Well I am hearing another issue, it's the rear end!
1. About how much does it cost to rebuild a 72' rear end?
2. Can't you buy a kit for the rear end and use a more modern one, say from a later 75'-80's? I thought there was a kit you can buy and weld it on to match our coil rear??
Posted via Mobile Device

Oh and it's a LWB w/ what was called a short tail th350 trans?
One piece drive shaft is what I am running currently.

I had not been driving it much due to no exhaust! But now I have exhaust and I can hear the little noises! Thx

Big Fenders · 02-10-2013, 09:49 PM

I neede a longer yoke for my project [th350] and a yoke for a 700r4 was what I used..
Bob

02-08-2013, 10:55 PM	#1
Hx16457 Registered User Join Date: Sep 2012 Location: Lawton Oklahoma Posts: 308	Tail shaft vs yoke Tell me; Does anyone know how much of the yoke has to reach inside the tail shaft to get a good seal and contact enough of the actual tail shaft to get good surface area contact and good torque? Note: I am in need of this information as it is compared to a, 350 V8, mounted in the front mounted position, with a th350, matched with a 1972 dif. With 3.73gears... Posted via Mobile Device __________________ People who make excuses didn't want to do it in the first place! http://s1326.photobucket.com/albums/...cpZZ1QQtppZZ16

02-08-2013, 11:09 PM	#2
Idaho64GMC Registered User Join Date: Feb 2013 Location: Twin Falls, Idaho Posts: 70	Re: Tail shaft vs yoke from what I've read there should be less than an inch of the yoke exposed, so bottom the yoke out and pull it out to 3/4 or an inch exposed and you should be good

02-09-2013, 07:33 AM	#3
Tx Firefighter Watch out for your cornhole ! Join Date: Jun 2003 Location: Azle, Texas Posts: 14,162	Re: Tail shaft vs yoke Ideally, the yoke should be bottomed, then pulled out 3/4 of an inch. Again, that's ideal and what my driveshaft shop uses for building one. You'll still be fine if it's 1/2 or even up near 1 inch though.

02-09-2013, 07:54 AM	#4
Hx16457 Registered User Join Date: Sep 2012 Location: Lawton Oklahoma Posts: 308	Re: Tail shaft vs yoke Okay thx for the replays. I need a longer shaft, then. Mine is pulled out approx. 2 or more inches from the tail shaft... It sounds like I need one at least 1.25" longer to get me closer to the tail piece. Posted via Mobile Device __________________ People who make excuses didn't want to do it in the first place! http://s1326.photobucket.com/albums/...cpZZ1QQtppZZ16

02-09-2013, 01:23 PM	#5
Hx16457 Registered User Join Date: Sep 2012 Location: Lawton Oklahoma Posts: 308	Re: Tail shaft vs yoke Anybody else running a similar set-up, with a one piece that could tell me the donor they used? Posted via Mobile Device __________________ People who make excuses didn't want to do it in the first place! http://s1326.photobucket.com/albums/...cpZZ1QQtppZZ16

02-09-2013, 08:15 PM	#6
Hx16457 Registered User Join Date: Sep 2012 Location: Lawton Oklahoma Posts: 308	Re: Tail shaft vs yoke Bump.... Anyone? Posted via Mobile Device __________________ People who make excuses didn't want to do it in the first place! http://s1326.photobucket.com/albums/...cpZZ1QQtppZZ16

02-10-2013, 01:25 PM	#7
61K10 Registered User Join Date: Feb 2012 Location: pleasant valley--placerville ca Posts: 3,039	Re: Tail shaft vs yoke they do make different length yoke's i think. speedway catalog? might just work. __________________ 1961 chevy K10 my build is------------61K10 build

02-10-2013, 01:44 PM	#8
Tx Firefighter Watch out for your cornhole ! Join Date: Jun 2003 Location: Azle, Texas Posts: 14,162	Re: Tail shaft vs yoke No one is going to be able to give any recommendation on a donor driveshaft without knowing what length transmission your th350 (there are 3 different length th350 trans) is and whether your truck is long or short wheelbase. Posted via Mobile Device

02-10-2013, 01:50 PM	#9
tincan1966 Registered User Join Date: Oct 2010 Location: Independence,KS Posts: 1,477	Re: Tail shaft vs yoke I noted in the posting that the engine is in the forward mounting location? Why not move it back to where a V8 normally mounts and solve the problem? Are you running a 2 piece drive shaft? If so, then the engagement of the yoke isn't nearly as critical,as long as you have about 75% engaged, because you have no risk of it bottoming out during suspension compression. Excuse me if I am missing something. Last edited by tincan1966; 02-10-2013 at 01:53 PM. Reason: added text.

02-10-2013, 07:14 PM	#10
Hx16457 Registered User Join Date: Sep 2012 Location: Lawton Oklahoma Posts: 308	Re: Tail shaft vs yoke Well I am hearing another issue, it's the rear end! 1. About how much does it cost to rebuild a 72' rear end? 2. Can't you buy a kit for the rear end and use a more modern one, say from a later 75'-80's? I thought there was a kit you can buy and weld it on to match our coil rear?? Posted via Mobile Device Oh and it's a LWB w/ what was called a short tail th350 trans? One piece drive shaft is what I am running currently. I had not been driving it much due to no exhaust! But now I have exhaust and I can hear the little noises! Thx __________________ People who make excuses didn't want to do it in the first place! http://s1326.photobucket.com/albums/...cpZZ1QQtppZZ16 Last edited by Hx16457; 02-10-2013 at 07:20 PM.

02-10-2013, 09:49 PM	#11
Big Fenders Registered User Join Date: Mar 2008 Location: Tucson Arizona Posts: 264	Re: Tail shaft vs yoke I neede a longer yoke for my project [th350] and a yoke for a 700r4 was what I used.. Bob

Thread Tools
Show Printable Version Email this Page
Display Modes
Switch to Linear Mode Hybrid Mode Switch to Threaded Mode



Register or Log In To remove these advertisements.

Register or Log In To remove these advertisements.