The 1947 - Present Chevrolet & GMC Truck Message Board Network







Register or Log In To remove these advertisements.

Go Back   The 1947 - Present Chevrolet & GMC Truck Message Board Network > 47 - Current classic GM Trucks > The 1967 - 1972 Chevrolet & GMC Pickups Message Board

Web 67-72chevytrucks.com


Reply
 
Thread Tools Display Modes
Old 05-05-2013, 06:34 PM   #1
Gumby'sC20
Registered User
 
Gumby'sC20's Avatar
 
Join Date: Jan 2009
Location: Binghamton, N.Y.
Posts: 116
Finally began reviving my '71 C20. Need some NV3500 swap guidance!

Hey everyone!

It's been years since I posted last, and in the meantime, things went downhill - and back uphill for my '71 C20.

About 2 years ago, the Goodwrench 350 replacement crate motor decided to finally give up, and spin a rod bearing. The truck sat for a while after that, and a few months ago, we began reviving the drivetrain.

A quick summary of what's going on with the engine: It's now a 355 block, which will be equipped with an RV cam (Melling MTC-1), Edelbrock Performer intake, Z28 valve springs (I know that's a pretty slang term) and headers. I plan on running the stock Q-Jet for now. Everything else about the engine will be stock.

Where I need some help is with the 5 speed swap I'm going to run. I picked up a 1993+ NV3500 5 speed to replace the 4 speed Muncie SM465 my truck came with from the factory.

Correct me if I'm wrong, but I believe I'll be able to reuse my flywheel (that the Muncie utilized), and run a clutch kit from a 1993+ 5.0L V8 C1500.

I'm unsure of what starter to use, and any input on that would be great!

Also, The transmission didn't come with the clutch fork pivot ball hardware and I'm unsure what to use for that, or where to get it.

Next, it's clear that I'll have to use a 32-spline slip yolk on the output shaft of the NV3500 (they don't accommodate a bolt-on unit), but I'm not sure which one to get to work with the 1350 U-Joint my truck uses (if I'm even correct on the U-Joint #).

Knowing that I'll be using a slip yolk up front at the trans, does that mean that the rest of the 2-piece driveshaft will have to be altered (aside from length, which will need to be altered)? In other words: if I recall correctly, the rear driveshaft on my truck that bolts to the 4:10 rear-end is also a slip system near the driveshaft carrier bearing, and I heard that if running a slip yoke, the rest of the driveshaft needs to remain firmly assembled together (read: no additional slip points used in the driveshaft assembly).

I think that's enough questions for now. Hopefully some of you will be able to help me on this! Thanks a ton, in advance!
Gumby'sC20 is offline   Reply With Quote
Old 05-06-2013, 06:10 PM   #2
Gumby'sC20
Registered User
 
Gumby'sC20's Avatar
 
Join Date: Jan 2009
Location: Binghamton, N.Y.
Posts: 116
Re: Finally began reviving my '71 C20. Need some NV3500 swap guidance!

Bump. Anyone?
Gumby'sC20 is offline   Reply With Quote
Old 05-06-2013, 08:30 PM   #3
LockDoc
The Older Generation


 
LockDoc's Avatar
 
Join Date: Aug 2006
Location: Montezuma, Iowa
Posts: 25,773
Re: Finally began reviving my '71 C20. Need some NV3500 swap guidance!

-
http://67-72chevytrucks.com/vboard/s...d.php?t=313954

LockDoc
__________________
Leon

Locksmith, Specializing In Antique Trucks, Automobiles, & Motorcycles

(My Dually Pickup Project Thread)

http://67-72chevytrucks.com/vboard/s...d.php?t=829820

-
LockDoc is offline   Reply With Quote
Old 05-08-2013, 07:44 PM   #4
Gumby'sC20
Registered User
 
Gumby'sC20's Avatar
 
Join Date: Jan 2009
Location: Binghamton, N.Y.
Posts: 116
Re: Finally began reviving my '71 C20. Need some NV3500 swap guidance!

Saw some info in post #67 in the thread you've posted which was helpful. Thanks, LockDoc.

Anyone else have any insight?
Gumby'sC20 is offline   Reply With Quote
Old 05-12-2013, 09:16 PM   #5
Gumby'sC20
Registered User
 
Gumby'sC20's Avatar
 
Join Date: Jan 2009
Location: Binghamton, N.Y.
Posts: 116
Re: Finally began reviving my '71 C20. Need some NV3500 swap guidance!

Answered my starter motor question. I was confused in looking at starters, as the Muncie had one that bolted to it's bellhousing. I now know the the starter I will need to use now bolts to the block.

Also, I found the clutch fork pivot hardware for sale online: http://www.allstategear.com/NV3500%2...Ball%20Kit.htm

^ That's the only place I've been able to locate any info about what hardware is used on the pivot ball.
Gumby'sC20 is offline   Reply With Quote
Reply

Bookmarks

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -4. The time now is 11:06 PM.


Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2024, vBulletin Solutions Inc.
Copyright 1997-2022 67-72chevytrucks.com