The 1947 - Present Chevrolet & GMC Truck Message Board Network







Register or Log In To remove these advertisements.

Go Back   The 1947 - Present Chevrolet & GMC Truck Message Board Network > 47 - Current classic GM Trucks > The 1947 - 1959 Chevrolet & GMC Pickups Message Board

Web 67-72chevytrucks.com


Reply
 
Thread Tools Display Modes
Old 06-07-2013, 10:27 PM   #1
roger55
Registered User
 
roger55's Avatar
 
Join Date: Feb 2010
Location: San Angelo, Tx
Posts: 1,068
Fender and hood emblem rechroming

I'd like to have mine rechromed. Does anyone have any recommendations on a place that does this?

I've got a '57 3200 pickup and they only have the repro fender emblems for other models. I know I can get a repro one for the hood but they are really expensive.

There is a little pitting on them but not really bad. I used some sandpaper on one of the worst pits but as you can see, it is still there but it is smaller than it was.



roger55 is offline   Reply With Quote
Old 06-07-2013, 10:46 PM   #2
Jyman
Registered User
 
Join Date: Aug 2012
Location: Sherwood park, Alberta, Canada
Posts: 91
Re: Fender and hood emblem rechroming

I can't help you with a place to get it rechromed. but If I remember my grandfather had said something about using Vaseline and steel wool on pitted chrome. he said the steel wool takes the pits out and the Vaseline helps protect the chrome. I don't know something to maybe try, but maybe someone can chime in on this that's done it.
__________________
1948 Chevy
305, NV3500, 3.73 rear, sitting on a 95 s10 frame. Still in the works

2000 Chevy Extreme lowrider, 4.3, NV3500, 3.08 rear, upgraded/modded

2001 GMC Sonoma Zr2, 4.3, NV3500, Stock
Jyman is offline   Reply With Quote
Old 06-08-2013, 12:31 AM   #3
parkwood
Registered User
 
parkwood's Avatar
 
Join Date: Jul 2011
Location: shingle springs, calif
Posts: 771
Re: Fender and hood emblem rechroming

I'm sure you'll find a good place in TX to have you parts plated.. the pits can be taken out and they do that by stripping the part and then depending on the shop solder or copper plating it and buffing it smooth then nickel plate then chrome... your's look to be in really nice shape and will fit you truck much better than re pops.. just don't drop dead from sticker shock...
parkwood is offline   Reply With Quote
Old 06-08-2013, 01:59 AM   #4
fabguy
Elev8r Man
 
fabguy's Avatar
 
Join Date: Aug 2010
Location: Glendora, CA
Posts: 835
Re: Fender and hood emblem rechroming

I am having my grill and parking light bezels & ashtray re chromed all for the low price (yeah right) of 450.00 I chose this route over reproduction because I know it will fit better and it seems that rechroming lasts longer than new repops
Posted via Mobile Device
__________________
1955.2 C4 Carry-all / Suburban ---> 55.2 Build Thread!!
1958 Fleetside SWB ---> 58 Fleetside Build thread
1939 2 door sedan

My F.B. project page.
fabguy is offline   Reply With Quote
Old 06-08-2013, 02:23 AM   #5
Jyman
Registered User
 
Join Date: Aug 2012
Location: Sherwood park, Alberta, Canada
Posts: 91
Re: Fender and hood emblem rechroming

for $450 that's not bad for all of those parts, they told me when I asked about just my grill getting rechromed that they will start at $1,000 and go from there.
__________________
1948 Chevy
305, NV3500, 3.73 rear, sitting on a 95 s10 frame. Still in the works

2000 Chevy Extreme lowrider, 4.3, NV3500, 3.08 rear, upgraded/modded

2001 GMC Sonoma Zr2, 4.3, NV3500, Stock
Jyman is offline   Reply With Quote
Old 06-09-2013, 06:41 AM   #6
1project2many
Registered User
 
Join Date: Mar 2012
Location: Lakes Region NH
Posts: 3,200
Re: Fender and hood emblem rechroming

I had my 3200 fender emblems, door V's, hood emblem, and turn signal done by a place in MT called Classic Plating. That was quite a few years ago but they've held up well. I think I paid $350 in '97 or '98. One of the fender spears had a damaged tip that they had to repair and apparently it took a fair amount of time. Both of the V's were pretty well pitted, too.

The real trick was painting the emblem again. I really wanted to duplicate the factory look. Ended up using a Q-tip to grease the tops of the letters and the emblem then sprayed the whole thing. After the paint had cured for a bit I just scraped off the paint where the grease had been applied. Worked well. That was after trying a *bunch* of different things based on suggestions from guys that had never BTDT.
1project2many is offline   Reply With Quote
Old 06-09-2013, 09:48 AM   #7
Tomb23
Registered User
 
Join Date: May 2004
Location: Eastern Oregon
Posts: 201
Re: Fender and hood emblem rechroming

These guys are Great !!


www.facebook.com/nwchrome

http://www.nwchromeinc.com/
Tomb23 is offline   Reply With Quote
Old 06-09-2013, 03:57 PM   #8
Russell Ashley
Registered User
 
Russell Ashley's Avatar
 
Join Date: May 2010
Location: Lawrenceville, Ga
Posts: 2,648
Re: Fender and hood emblem rechroming

It's a coincidence that this topic would be mentioned now, as I painted mine just this past Saturday. They are easy to tape up due to the shape of the piece, but getting the paint off of the letters is the trick. I painted mine with Rustoleum Regal red. As soon as the paint flashed off I removed the tape, then held a rag tightly over the tip of my finger, wet it with lacquer thinner, and wiped the paint off of the top of the letters. You have to do it a few times, changing the rag position and re-wetting it each time, to get the letters completely clean. It's really not difficult as the letters are raised high enough to get to just the tops easily. The dark spots around the red part in the pic are shadows of the letters, not a sloppy tape job. Mine need replaced or rechromed too but that will have to wait due to other more pressing needs.
Attached Images
 
Russell Ashley is offline   Reply With Quote
Old 06-11-2013, 06:00 PM   #9
oldcouple
Registered User
 
oldcouple's Avatar
 
Join Date: Nov 2011
Location: Winlock Wa
Posts: 584
Re: Fender and hood emblem rechroming

Quote:
Originally Posted by Russell Ashley View Post
It's a coincidence that this topic would be mentioned now, as I painted mine just this past Saturday. They are easy to tape up due to the shape of the piece, but getting the paint off of the letters is the trick. I painted mine with Rustoleum Regal red. As soon as the paint flashed off I removed the tape, then held a rag tightly over the tip of my finger, wet it with lacquer thinner, and wiped the paint off of the top of the letters. You have to do it a few times, changing the rag position and re-wetting it each time, to get the letters completely clean. It's really not difficult as the letters are raised high enough to get to just the tops easily. The dark spots around the red part in the pic are shadows of the letters, not a sloppy tape job. Mine need replaced or rechromed too but that will have to wait due to other more pressing needs.
A fresh single edge razor blade will clean up the tops of the letters just fine, no worry about thinner running down and melting the paint.
__________________
Retired and too busy to work.
oldcouple is offline   Reply With Quote
Old 06-12-2013, 07:21 AM   #10
Russell Ashley
Registered User
 
Russell Ashley's Avatar
 
Join Date: May 2010
Location: Lawrenceville, Ga
Posts: 2,648
Re: Fender and hood emblem rechroming

Quote:
Originally Posted by oldcouple View Post
A fresh single edge razor blade will clean up the tops of the letters just fine, no worry about thinner running down and melting the paint.
Have you actually done it that way? It wouldn't work with mine because the letters have a slight amount of "flash" around the edges that raises the edge of some of the letters. Not much, but enough to prevent using a razor blade to scrape it off. Also, you don't soak the rag enough that the thinner would drip, and you wrap it tightly around your finger so that it only touches the tops of the letters. You do it before the paint has fully set and it wipes off easily. Just saying what worked for me, and mine came out perfect.
Russell Ashley is offline   Reply With Quote
Old 06-09-2013, 09:23 PM   #11
Rude Dude
Registered User
 
Rude Dude's Avatar
 
Join Date: Sep 2005
Location: Glendale Arizona
Posts: 1,188
Re: Fender and hood emblem rechroming

Petroleum Jelly (Vaseline) also works great. I have used it when painting the emblems covering the leters with a Q Tip or small flat modeler's brush painting then waiting til it is dry in a day or two.

Quote:
Originally Posted by 1project2many View Post
I had my 3200 fender emblems, door V's, hood emblem, and turn signal done by a place in MT called Classic Plating. That was quite a few years ago but they've held up well. I think I paid $350 in '97 or '98. One of the fender spears had a damaged tip that they had to repair and apparently it took a fair amount of time. Both of the V's were pretty well pitted, too.

The real trick was painting the emblem again. I really wanted to duplicate the factory look. Ended up using a Q-tip to grease the tops of the letters and the emblem then sprayed the whole thing. After the paint had cured for a bit I just scraped off the paint where the grease had been applied. Worked well. That was after trying a *bunch* of different things based on suggestions from guys that had never BTDT.
Rude Dude is offline   Reply With Quote
Old 06-10-2013, 01:51 AM   #12
TX58
Registered User
 
Join Date: Dec 2011
Location: Humble,TX
Posts: 287
Re: Fender and hood emblem rechroming

I had my '58 fender spears,hood trim, and interior fresh air vents done at a shop here in Houston for about $800
They look great
Posted via Mobile Device
TX58 is offline   Reply With Quote
Old 06-10-2013, 03:50 PM   #13
_Ogre
Registered User
 
_Ogre's Avatar
 
Join Date: Jan 2012
Location: Motown
Posts: 7,680
Re: Fender and hood emblem rechroming

you could always airbrush them on





low profile ''chrome''

__________________
cool, an ogre smiley Ogre's 58 Truk build

how to put your truck year and build thread into your signature
shop air compressor timer
_Ogre is offline   Reply With Quote
Old 06-10-2013, 09:05 PM   #14
1project2many
Registered User
 
Join Date: Mar 2012
Location: Lakes Region NH
Posts: 3,200
Re: Fender and hood emblem rechroming

Beautiful.

In my case I'd be lucky if I could airbrush yellow paint onto the side of that truck, let alone a low profile chrome emblem.
1project2many is offline   Reply With Quote
Old 06-10-2013, 09:46 PM   #15
mr48chev
Registered User
 
mr48chev's Avatar
 
Join Date: Jul 2007
Location: Toppenish, WA
Posts: 15,708
Re: Fender and hood emblem rechroming

I'd suggest attending a few shows in the area and talking to guys who have fresh looking chrome who did their chrome. Chrome work on their cars, trucks and bikes is one thing that guy are usually willing to talk about to some extent and most will tell you straight off how they feel about the quality of the work and the price they paid. Around this area I couldn't even begin to tell you the closest place to have chrome done outside of Portland or Seattle.
__________________
Founding member of the too many projects, too little time and money club.

My ongoing truck projects:
48 Chev 3100 that will run a 292 Six.
71 GMC 2500 that is getting a Cad 500 transplant.
77 C 30 dualie, 454, 4 speed with a 10 foot flatbed and hoist. It does the heavy work and hauls the projects around.
mr48chev is offline   Reply With Quote
Reply

Bookmarks

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -4. The time now is 09:12 PM.


Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2024, vBulletin Solutions Inc.
Copyright 1997-2022 67-72chevytrucks.com