Inner fender help - The 1947 - Present Chevrolet & GMC Truck Message Board Network

brad20653 · 07-30-2003, 06:42 PM

Is the inner fender hard to put in on a 68 ? How do they go in and whats needed ? Pics would hlp

Warbones · 07-30-2003, 06:55 PM

Good question. I have one on the passenger side of my 67 that will need swapping out as soon as I locate one that is without rust.

70c10 · 07-30-2003, 06:59 PM

Inner fenders are usually pretty easy to install. I think there is about 7 bolts from what I remember, it's been awhile.

bigvinnie · 07-30-2003, 07:20 PM

jack up the truck, pull the tire/wheel, unbolt the old inner fender and bolt in the new one...

Be safe.....use jack stands !!!

Longhorn Man · 07-30-2003, 08:49 PM

Don't even need to pull the wheel really.
The real PITA will be when 1/2 of your bolts break from the rust.

treefrog · 07-30-2003, 08:49 PM

USE JACK STANDS. I think if you turn the wheel a bit off center it makes it easier to get out. Really easy. Oh by the way, use jack stands.
TF
Did I mention, use jack stands?

07-30-2003, 06:42 PM	#1
brad20653 Senior Member Join Date: Jul 2003 Location: So. MD Posts: 218	Inner fender help Is the inner fender hard to put in on a 68 ? How do they go in and whats needed ? Pics would hlp

07-30-2003, 06:55 PM	#2
Warbones Navel Inspector Join Date: Mar 2003 Location: Wichita, Ks Posts: 1,373	Good question. I have one on the passenger side of my 67 that will need swapping out as soon as I locate one that is without rust. __________________ 1948 Chevy Aerosedan GONE! I think. 1984 Cadillac Fleetwood Brougham Coupe WANTED 1967 IMPALA 1967 CST C10 Long Bed with a 283

07-30-2003, 06:59 PM	#3
70c10 67-72 Addict! Join Date: Feb 2002 Location: The TAX State! Posts: 7,857	Inner fenders are usually pretty easy to install. I think there is about 7 bolts from what I remember, it's been awhile. __________________ Jim 1970 C/10 Fleetside w/Ghost Flames Lowered 4.5" front and 4" rear (Raked) 355/350 Turbo w/shift kit 10" Redneck Performance Verter w/2500 stall Hooker Super Comps part#2808-1 Performer RPM Air-Gap 12 Bolt w/3:73 gears- Eaton Posi Comp Cams XE262 with 1.6 Crane Energizers, Road Demon 625 and Brodix IK 180 heads

07-30-2003, 07:20 PM	#4
bigvinnie Registered User Join Date: Aug 2001 Location: escondido, ca 92026 Posts: 1,222	jack up the truck, pull the tire/wheel, unbolt the old inner fender and bolt in the new one... Be safe.....use jack stands !!! __________________ '72 short step, 350, 700R4, tilt, ps, pdb, a/c, lowered coils, etc., other work in progress... San Diego, CA 72 Stepside Project Last edited by bigvinnie; 07-30-2003 at 07:25 PM.

Thread Tools
Show Printable Version Email this Page
Display Modes
Switch to Linear Mode Hybrid Mode Switch to Threaded Mode

07-30-2003, 08:49 PM	#5
Longhorn Man its all about the +6 inches Join Date: Jan 2001 Location: Hilliard Ohio Posts: 2,693	Don't even need to pull the wheel really. The real PITA will be when 1/2 of your bolts break from the rust.

07-30-2003, 08:49 PM	#6
treefrog Registered User Join Date: May 2002 Location: Knoxville, TN USA Posts: 189	USE JACK STANDS. I think if you turn the wheel a bit off center it makes it easier to get out. Really easy. Oh by the way, use jack stands. TF Did I mention, use jack stands?



Register or Log In To remove these advertisements.

Register or Log In To remove these advertisements.