For those of you that painted interior plastic..

[IdahoMan]

How's it holding up? Do you have before/after pics?

The idea of painting plastic panels doesn't set well with me (should be the color it is when it is mixed/melted IMO), but people to do it.

And what type of plastic are the door panels/kickpanels/whatnot made of? I have to repair mine; I'm sure aftermarket is crap.

(damaged interior panel pic below)

Thanks.


IM

[TKCR]

I did all of mine and it's holding up just fine, it's been a year or less on some parts. I used Buford's Aerosol Vinyl Dye. I went from the burgundy interior to a graphite grey. It was easy an affordable.

Here's before, during & after on the door panels

[TKCR]

And then the dash panel

[TKCR]

I really don't have any pics of the interior before, but it was all burgundy. I also recovered the headliner.

[Greasey Harley]

Can't find a blue replacement part?
I have never dyed plastic, but I have bought rigs that were dyed, and it always flaked off, eventually.
Should be easy to find in a wrecking yard, Craigslist, etc. Sometimes I get parts from a local tow yard.
I don't know what part of ID you're in, but there is no shortage of square-body parts trucks around here.

[homemade87]

Heres my blue interior . The dash is a oem dash that has been painted for years . The rest is oem parts that has been painted . I sprayed the whole interior . I went to a local paint shop and had them mix me a quart and did the whole interior when I did the resto . Worked great for me . If you prep correctly it will work fine . Just remember to clean clean clean and then clean some more . Its all about prep .

You are correct that aftermarket is crap . I orderd a couple pieces when I was doing mine and said nope . I sent them back and found oem stuff and repaired if needed . It looked so much better .

Sorry , No before pictures. Every thing you see has been painted .

[hatzie]

Originally Posted by IdahoMan

How's it holding up? Do you have before/after pics?

The idea of painting plastic panels doesn't set well with me (should be the color it is when it is mixed/melted IMO), but people to do it.

And what type of plastic are the door panels/kickpanels/whatnot made of? I have to repair mine; I'm sure aftermarket is crap.

(damaged interior panel pic below)

Thanks.

IM

This is a short howto article on identifying interior plastics.
http://www.urethanesupply.com/identify.php
I'd almost be willing to bet the interior on our trucks pre-dates the requirement for Recycling ID marks but there are other ways outlined in the article.

[Speeding Dakota]

What piece are you looking for, as I have some extra blue interior trim sitting around.

[IdahoMan]

Originally Posted by Speeding Dakota

What piece are you looking for, as I have some extra blue interior trim sitting around.

The piece that are cracked at the ones pictured bellow.

I. Squeezes in between the dashpad and the door; Rright.
II. Covers the back pillar; Left.
III. Covers the back pillar; Right.

[SCOTI]

Originally Posted by IdahoMan

The piece that are cracked at the ones pictured bellow.

I. Squeezes in between the dashpad and the door; Rright.
II. Covers the back pillar; Left.
III. Covers the back pillar; Right.

Those type of repairs would be noticed. I doubt you could fuse the pieces together & manipulate the texture to hide the repairs.

I would hit the wrecking yards or look for someone parting a similar truck out. Search the classifieds on here & your local craigslist. The OE pieces from another truck can be died/painted to match. It might require painting all the trim for color consistency though or you possibly could find blue pieces & just swap them in place.

[SCOTI]

Original interior plastics can be painted. The key to success is 90% in the prep.

Aftermarket interior pieces can be plastic or poly based. Very difficult to get anything to adhere properly to poly items. Some mfr's even put disclaimers up & recommend not painting.

[dieseldawg142]

yeah, i too was real sceptical about painting door panels, but availability & price made painting the answer for me.
scrub the bejeezus out of them, i used tsp, it is a good cleaner, & adhesion promoter before you spray.
the front panels in my crew, painted the arm rest too

the rear doors

did my sunvisors as well

i painted mine about 2 yrs ago with all SEM stuff, holding up fine even with my 10 yr old & his friends beating the snot out of the back. only spots so far is if you lift up the window crank washers, some of the paint is wore off behind them

[tucsonjwt]

SEM worked good for me. The surface texture was shot on the door panels so I wet sanded them and used adhesion promoter and a slightly darker color. If you texture is worn away I don't think you can bring it back. In my case, I did not care.

[old Rusty C10]

I don't have pics I used SEM the thing is tho you can paint it with anything and it wont be worth a hoot if you don't prep it right I cleaned twice with prepsol then I used the plastic primer stuff ( activator or whatever they call it) they sell at the auto body supply store

[BLP86]

I just purchased the part for right and left sides you have listed in your first pic from LMC, $9.95 a piece plus shipping and they fit perfectly for my 86 C10. The other parts are available from them too.

[truckfan]

after. i will look for before. dash was red. door panels were dark grey. SEM and followed all directions. seems to hold up to anything but a direct hit with something sharp

[IdahoMan]

Originally Posted by truckfan

..seems to hold up to anything but a direct hit with something sharp

Like dog claws?

[JWall]

I redid my interior exactly 2 years ago.
The trim pieces that I painted where originally blue covered easily but like said above prep is very important.
I washed my pieces several times, then cleaned them with TSP cleaner, then used SEM adhesion promoter, then used SEM Landau Black.
It has held up well. And touches up well too... (I scratched a kick panel)



I even cleaned and painted the shelf for behind the rear set that was grey tweed. It covered well too & it gets some use.



I did buy my door panels aftermarket which came black so I'm not sure how those would hold probably getting touched and used the most. But I like the SEM stuff enough that I'd love to get some GM door panels and try it.

P.S. I ordered some aftermarket pillar trim pieces in the beginning and they were junk... flimsy & didn't fit right.... they got tossed.

Here's my final result...

[Robert8096]

Like everyone states prep is the key to dyeing plastic. I am in the middle of an interior refurbish.

I used bumper repair kit to repair broken pieces and to fill the holes in my original door panels where the map pockets once lived.

http://www.amazon.com/Bondo-280-Bumper-Repair-Syri...

On the parts that had dead plastic, I cleaned them real good. Then used a red scotch bright pad to clean off the remaining dead plastic. Cleaned them again, shot some SEM plastic adhesion promoter, then sprayed them with some Rustolumen truck bed liner to give them a uniformed texture. I let the bed coating dry for a week and then went back with a scotch bright pad and took the sharpness off the coating and got the texture to my liking. Sprayed them the color I wanted, let them sit for 24 hours and sprayed them with a plastic clear. I am going Torch red so I used dye from a corvette supplier.

http://www.semproducts.com/automotiv...esion-promoter

http://www.summitracing.com/parts/rl...FUoV7AodEWwATw

http://www.mamotorworks.com/Corvette...lding-601950-1

http://www.mamotorworks.com/Corvette...-12oz-106135-1

Pics of the results so far:

[tylerg85]

It's all in the prep. Mines still doing great. Also covered my headliner in suede.

[77K10Silverado]

Cool headliner!

[tylerg85]

Thanks. I also wrapped the cloth inserts in the door panels with the same material. It's the little things that make a truck different. I don't think it turned out to terrible for my first time on both the doors and headliner

[Chaplain]

Nice job on panels as well as the headliner.

[DT3Ton]

Sorry to necro this thread..

A number of you have said you used SEMs adhesion promoter but there are different kinds of adhesion promoters.

I have this document called SEM training manual. Within it says to use 3836(x) SAND FREE for ABS and PVC. It says to use 3986(x) or 7772(x) for TPO, EDPM, PP and other similar thermoplastics. To tell the difference, it says acetone will melt/smear the former and not the latter. The door panels from my 79 and 84 don't seem to be affected by acetone. Problem is I can get the 3836 locally but I'm having trouble sourcing the latter two.

So specifically which adhesion promoter have you used or better yet, what type of plastic are the factory door panels?

[Robert8096]

I used SEM soap 39362 and then 39863 on my factory panels.