![]() |
|
![]() |
#1 |
Registered User
Join Date: May 2010
Location: jackson, michigan
Posts: 246
|
engine vibration
I've noticed that I'm getting a serious vibration in the engine just above idle, but smooths out at higher RPM. Is this the sign of a bad vibration dampener or are there other possibilities. Does same thing sitting in neutral or going down the street. The dampener appears to be shaking a little I've noticed.
|
![]() |
![]() |
![]() |
#2 | |
Senior Member
![]() Join Date: Aug 2013
Location: corktown,mi.
Posts: 5,194
|
Re: engine vibration
Quote:
|
|
![]() |
![]() |
![]() |
#3 |
Senior Member
![]() Join Date: Aug 2013
Location: corktown,mi.
Posts: 5,194
|
Re: engine vibration
|
![]() |
![]() |
![]() |
#4 |
Post Whore
![]() Join Date: Mar 2013
Location: Southern Oregon
Posts: 10,384
|
Re: engine vibration
Check the that dampner for sure. That'll cause vibration...also check for loose bolts in the pressure plate and clutch area...What engine?
__________________
1966 Chevy C10 "Project Two Tone" http://67-72chevytrucks.com/vboard/s...d.php?t=596643 1964 GMC "Crustine" semi-build:http://67-72chevytrucks.com/vboard/s...d.php?t=665056 My youtube channel. Username "Military Chevy": https://www.youtube.com/channel/UC_h...fzpcUXyK_5-uiw |
![]() |
![]() |
![]() |
#5 |
Senior Member
![]() Join Date: Aug 2013
Location: corktown,mi.
Posts: 5,194
|
Re: engine vibration
|
![]() |
![]() |
![]() |
#6 |
Registered User
Join Date: May 2010
Location: jackson, michigan
Posts: 246
|
Re: engine vibration
it's a 350 with 700r4. It runs excellent idling and very good upon accelerating, but vibrates just at one speed.
|
![]() |
![]() |
![]() |
#7 |
Registered User
Join Date: Jun 2011
Location: WNC
Posts: 226
|
Re: engine vibration
Is the vibration while your standing still; not driving? Did the problem just start, out of the blue? Or did it come with an engine swap or rebuild?
Some possibilities are: missfire, loose clutch or flywheel, weak or broken motor mounts and the dampener (balancer). I'll be watching this thread cuz I'm chasing this same issue in my 305 V8. It shudders between 1000 and 2000 RPMs.
__________________
`63 C-10 Shortwide Roller 305 LT1 cam, Eddy 500 T5 |
![]() |
![]() |
![]() |
#8 |
Registered User
Join Date: Sep 2014
Location: Olympia, Washington
Posts: 172
|
Re: engine vibration
My original 283 in my '62 was buzzing just like that.
Mine did it between 2,200 to 2,400 rpms sitting still. I isolated the trans, clutch, pressure plate, fan, water pump, harmonic damper basically everything I could think of. My solution?? Pulling the motor and putting a new crate 350 in it! I'm pretty convinced that the old 283 was just tired and had sloppy tolerances so it was time for a change. It was no fun at all driving it with the vibe because it was right in the meat of the powerband you always drove at....I couldn't take it anymore. Should be like a whole different truck when I get her all back together. |
![]() |
![]() |
![]() |
#9 |
Registered User
Join Date: Sep 2012
Location: oceanside CA
Posts: 706
|
Re: engine vibration
im gonna say its a harmonic dampener .. make sure its seated on all the way ... also make sure that the lil keyway was put back in the crank before the dampener was put back on .. and lastly if these have been done. try buying a new one and put it on .. i will say it should not have any kind of wiggle to it at all when you are watching it run .. so i would tackle that 1st
|
![]() |
![]() |
![]() |
#10 |
Registered User
Join Date: May 2010
Location: jackson, michigan
Posts: 246
|
Re: engine vibration
it's a 350/700r4 that I installed 5yrs ago. The vibration is just above idle and goes away quickly on acceleration. Sitting still or moving, same deal. This just started. Think i'll start with the dampener as I can see a little wobble there. I 'll post what it was once I know.
|
![]() |
![]() |
![]() |
#11 | |
Registered User
Join Date: Jun 2014
Location: Glendale, Arizna
Posts: 1,642
|
Re: engine vibration
Quote:
But like previously mentioned, the balancer should not wobble at all. |
|
![]() |
![]() |
![]() |
#12 |
Registered User
Join Date: Sep 2014
Location: Olympia, Washington
Posts: 172
|
Re: engine vibration
I thought the same thing with my 283 (balancer). So I removed it, started engine...still shook between 2200-2400...that's when I yanked it outta the truck!
|
![]() |
![]() |
![]() |
#13 |
Six in a row makes it go...
![]() Join Date: Mar 2009
Location: Vacationland: Maine
Posts: 1,346
|
Re: engine vibration
I had the outer ring of the balancer slip relative to the inner on my 292. It gave vibrations at certain rpm and then smoothed out at others. A new balancer fixed it up. This may be your problem I dunno.
I had a buddy who was a mechanic. He warned against using Gunk engine cleaner and other such things on the balancer since he had seen the outer rings slip on more than one occasion.
__________________
67 C20 long step resto: http://67-72chevytrucks.com/vboard/s...d.php?t=342086 66 C10 long step build: http://67-72chevytrucks.com/vboard/s...=1#post3814790 CT to Alaska in a 67 C10: http://67-72chevytrucks.com/vboard/s...d.php?t=399224 “The height of sophistication is simplicity." - Clare Boothe Luce |
![]() |
![]() |
![]() |
Bookmarks |
Thread Tools | |
Display Modes | |
|
|