how low w/ bags and the stock bed floor? - The 1947 - Present Chevrolet & GMC Truck Message Board Network

jon_volk · 09-03-2003, 03:25 PM

how low can ya get w/ bags, notched frame, and the stock bed floor? pics?

SCOTI · 09-03-2003, 03:58 PM

**

SCOTI · 09-03-2003, 03:59 PM

should answer that question.

jon_volk · 09-03-2003, 06:14 PM

nice looking drop, sitting on the bumpstops? are you using an off the shelf frame notch or a custom made one?

Russell · 09-03-2003, 07:34 PM

I saw a Blazer that had the frame literally sitting on the ground... I didn't have a camera to take any pictures unfortunatly, but it was much lower than that truck is...

**N2TRUX** · 09-03-2003, 07:46 PM

Quote:

Originally posted by Russell
I saw a Blazer that had the frame literally sitting on the ground... I didn't have a camera to take any pictures unfortunatly, but it was much lower than that truck is...

I can assure you if it was layed out on the frame, it had the bed (body) cut. It takes a lot more to lay a Blazer on the ground than a truck

**N2TRUX** · 09-03-2003, 08:11 PM

Quote:

Originally posted by jon_volk
nice looking drop, sitting on the bumpstops? are you using an off the shelf frame notch or a custom made one?

Thanks, picture #2 is with the truck layed out.

Yes, it is on the bumpstops at that point. I had it set up where it will rest on the stops and still roll. It could be about an inch lower, but it would not roll.

No, the notch is not "off the shelf" or bolt in. It was custom made by Roger at Stoked Out Specialties Here is a pic...

loweredd · 09-03-2003, 08:17 PM

yes, not REAL low with stock floor. Specially if you have abigger sidewall like I found out. I had to cut out the floor clear across so the whole REAREND can come up into the bed!! Axle tubes and all.

gldevall · 09-03-2003, 10:23 PM

Hey loweredd, let's see some pics. I have been curious about those wheels also.

loweredd · 09-03-2003, 10:27 PM

LOL, I'm just about done. I am waiting on our BellTech rep to get back to me with a price on spindles.....my upper a-arms are WAY into my steering shaft. Then I will def. get some pics.

**N2TRUX** · 09-04-2003, 09:03 AM

Quote:

Originally posted by loweredd
LOL, I'm just about done. I am waiting on our BellTech rep to get back to me with a price on spindles.....my upper a-arms are WAY into my steering shaft. Then I will def. get some pics.

Yeah, whats the deal anyway. Don't you just hate it when people work on a project, and won't share pics with everyone

loweredd · 09-04-2003, 10:21 AM

LOL, I need to call him this morning as soon as they open. They have a 3200 spindle set for 125 for me......OH YEAH!

09-03-2003, 03:25 PM	#1
jon_volk Registered User Join Date: Mar 2003 Location: Milford, CT Posts: 242	how low w/ bags and the stock bed floor? how low can ya get w/ bags, notched frame, and the stock bed floor? pics?

09-03-2003, 03:59 PM	#3
SCOTI Registered User Join Date: Apr 2001 Location: DALLAS,TX Posts: 22,064	and this.... should answer that question. Attached Images __________________ 67SWB-B.B.RetroRod 64SWB-Recycle 89CCDually-Driver/Tow Truck 99CCSWB Driver All Fleetsides @rattlecankustoms in IG Building a small, high rpm engine with the perfect bore, stroke and rod ratio is very impressive. It's like a highly skilled Morrocan sword fighter with a Damascus Steel Scimitar..... *Cubic inches is like Indiana Jones with a cheap pistol.*

09-03-2003, 07:34 PM	#5
Russell Professional Grade Join Date: May 2003 Location: Fort McMurray, Alberta Posts: 7,915	I saw a Blazer that had the frame literally sitting on the ground... I didn't have a camera to take any pictures unfortunatly, but it was much lower than that truck is... __________________ 1995 Chevrolet 2 Door Tahoe (6.6L LBZ Duramax / ZF6 / NP241 with 1 ton solid axle swap)

09-03-2003, 10:23 PM	#9
gldevall Registered User Join Date: Mar 2003 Location: Walker, LA Posts: 2,925	Hey loweredd, let's see some pics. I have been curious about those wheels also. __________________ Gary -1986 SWB: lowered 4/6, SOLD!!! -Best 1/4 mile: 14.51 @ 91.01 MPH -2001 Pewter Tahoe, billet grill, Corsa Sport Cat-back, K&N FIPK SOLD!!! -2004 Z-71 Extended cab with a flowmaster, BDS 6.5", 3" BL, 35x12.5x18 Trail Grapplers on Pro-Comp 18x9 wheels

Thread Tools
Show Printable Version Email this Page
Display Modes
Switch to Linear Mode Hybrid Mode Switch to Threaded Mode

09-03-2003, 03:58 PM	#2
SCOTI Registered User Join Date: Apr 2001 Location: DALLAS,TX Posts: 22,064	this.... Attached Images __________________ 67SWB-B.B.RetroRod 64SWB-Recycle 89CCDually-Driver/Tow Truck 99CCSWB Driver All Fleetsides @rattlecankustoms in IG Building a small, high rpm engine with the perfect bore, stroke and rod ratio is very impressive. It's like a highly skilled Morrocan sword fighter with a Damascus Steel Scimitar..... Cubic inches is like Indiana Jones with a cheap pistol.**

09-03-2003, 06:14 PM	#4
jon_volk Registered User Join Date: Mar 2003 Location: Milford, CT Posts: 242	nice looking drop, sitting on the bumpstops? are you using an off the shelf frame notch or a custom made one?

09-03-2003, 08:17 PM	#8
loweredd www.loweredd.com Join Date: Aug 2002 Location: Struble IA Posts: 808	yes, not REAL low with stock floor. Specially if you have abigger sidewall like I found out. I had to cut out the floor clear across so the whole REAREND can come up into the bed!! Axle tubes and all.

09-03-2003, 10:27 PM	#10
loweredd www.loweredd.com Join Date: Aug 2002 Location: Struble IA Posts: 808	LOL, I'm just about done. I am waiting on our BellTech rep to get back to me with a price on spindles.....my upper a-arms are WAY into my steering shaft. Then I will def. get some pics.

09-04-2003, 10:21 AM	#12
loweredd www.loweredd.com Join Date: Aug 2002 Location: Struble IA Posts: 808	LOL, I need to call him this morning as soon as they open. They have a 3200 spindle set for 125 for me......OH YEAH!



Register or Log In To remove these advertisements.

Register or Log In To remove these advertisements.