|
|
|
06-08-2015, 12:27 PM
|
#1 |
|
Registered User
Join Date: Oct 2014
Location: Spearfish South Dakota
Posts: 407
|
Moter mount position
Ime pretty sure I know but. I pulled the 6 out cleaned up Eng. bay set v8 in had trouble stabbing the 4 speed but went to set motor mounts are in to close
And huge expletive!!! Now I see another set holes. the picture is looking strait down you can see the 2 holes above the mount exhaust manifold on top. just wanted to make sure that all it is needed to do.
__________________
83 c10 long Box Daily Driver 90 Jimmy parked 98 Road King/ 06 Road Glide In memorium 63 impala SS/ 65 Chevy Panel 65 GMC Short Box/ 68 Camero |
|
|
|
06-08-2015, 01:48 PM
|
#2 |
|
yeller
Join Date: Oct 2001
Location: Twin Cities
Posts: 13,824
|
Re: Moter mount position
The two sets are stamped/labeled "6" and "8" on the engine mount stands...put the engine mounts for the V8's in the "8" hole and inlines in the "6" hole. Just move the engine mounts on the stand, and you will be good to go.
__________________
Jeff 73-87.com 73-87.com Facebook page 73-87 cab corner 6x9 speaker brackets for sale 67-72 cab corner speaker brackets for sale 47-54 cab corner speaker brackets for sale |
|
|
|
|
06-08-2015, 04:31 PM
|
#3 |
|
Registered User
Join Date: Oct 2014
Location: Spearfish South Dakota
Posts: 407
|
Re: Moter mount position
Thanks didn't see it before set eng in getting old blind. when I started in shop at 19 those old guys back then always had a trouble light in there hand ime like get that out my eyes now I get it at 57
__________________
83 c10 long Box Daily Driver 90 Jimmy parked 98 Road King/ 06 Road Glide In memorium 63 impala SS/ 65 Chevy Panel 65 GMC Short Box/ 68 Camero |
|
|
|
|
06-08-2015, 06:35 PM
|
#4 |
|
Registered User
Join Date: Dec 2007
Location: Kimberley, BC, Canada
Posts: 799
|
Re: Moter mount position
Steve, I changed the mounts on my six years ago, so I knew about the two sets of bolt holes. As I remember, holding the nuts on the back was a bit of a challenge.
__________________
Greg 64 GMC Suburban - 283, NV3500, 14 bolt 77 C10 swb - 292, SM465, 12 bolt |
|
|
|
|
06-09-2015, 02:01 PM
|
#5 |
|
Registered User
Join Date: Oct 2014
Location: Spearfish South Dakota
Posts: 407
|
Re: Moter mount position
looks to me like pulling the mount brackets then move the mounts out with the brackets on the benchthen reinstall brackets is the way to go I think?
__________________
83 c10 long Box Daily Driver 90 Jimmy parked 98 Road King/ 06 Road Glide In memorium 63 impala SS/ 65 Chevy Panel 65 GMC Short Box/ 68 Camero |
|
|
|
|
06-09-2015, 03:25 PM
|
#6 |
|
yeller
Join Date: Oct 2001
Location: Twin Cities
Posts: 13,824
|
Re: Moter mount position
The bottom bolts on the plates, that go to the crossmember...are also a PITA to get to. Half a dozen of one, 6 of the other...either way, it kind of sucks.
__________________
Jeff 73-87.com 73-87.com Facebook page 73-87 cab corner 6x9 speaker brackets for sale 67-72 cab corner speaker brackets for sale 47-54 cab corner speaker brackets for sale |
|
|
|
|
06-09-2015, 04:26 PM
|
#7 |
|
Registered User
Join Date: Jul 2011
Location: WV
Posts: 946
|
Re: Moter mount position
Interesting. I swapped a 350 into my fathers truck (80 k10) that had a 250 in it from the factory. Dropped right in and everything lined up.
__________________
72 GMC C2500 402/Th400 first truck (still have) 77 GMC C3500 CC dually Sold  70 C50 dump truck "Rusty" 87 K10 Suburban Sold 93 K2500 xcab 6.5TD 96 GMC K2500 Suburban 6.5 TD |
|
|
|
 |
| Bookmarks |
| Thread Tools | |
| Display Modes | |
|
|
Hybrid Mode
