MO Parting a 69 C10 with small block and three on the tree.

[specialtyretail]

UPDATE,,,, BED IS SOLD,,,, DOORS ARE SOLD.... Was going to keep this one around the shop but the motor has quite the rattle on the top end, so it will give of itself so others may continue on. No part is too small, if it is the part you need. I cannot ship the bigger parts. The oil bath air cleaner is sold. . I would like to keep it where it will move under it's own power for the next few days. Before everyone freaks about me parting out a good truck, the firewall is about to fall away from the rest of the cab, the floor seams are rusted away,, the cab is shot. I am off work Friday so I should be able to get a lot of parts removed. If you need it and I have it, we can probably make a deal. Thanks, Fred.

[Rotorcycle]

Condition of interior rear view mirror?

[specialtyretail]

Originally Posted by Rotorcycle

Condition of interior rear view mirror?

Let me get you a pic in the morning. Thanks, Fred

[Cash3481]

Condition and price of the front bumper and upper bed trim.
I might be able to pick it up.

[specialtyretail]

Originally Posted by Cash3481

Condition and price of the front bumper and upper bed trim.
I might be able to pick it up.

Hey Mike. Let me get you some pics here in just a bit.. Thanks, Fred.

[Number98]

How bad is that upper bed trim?

[specialtyretail]

Originally Posted by Cash3481

Condition and price of the front bumper and upper bed trim.
I might be able to pick it up.

Hey Mike. The front bumper appears to be straight but the chrome is peeling off the ends, let me see about the bedside trim, I think there is just the one side. Thanks, Fred.

[57taskforce]

Fred, price on the passenger door trim and both pieces of cab trim please.
Thanks,
Tyler

[Rotorcycle]

Thanks for the pictures of rear view mirror, looking for a mirror glass in very good condition

[specialtyretail]

Originally Posted by Rotorcycle

Thanks for the pictures of rear view mirror, looking for a mirror glass in very good condition

No problem. Thanks, Fred.

[jimer1964]

Hi heater vents,are they the blue ones you have listed in the other post? Looking for some blue ones. Thanks

[specialtyretail]

Originally Posted by jimer1964

Hi heater vents,are they the blue ones you have listed in the other post? Looking for some blue ones. Thanks

That is them. Not sure if I would call them blue or green or bluish/green.

[jimer1964]

Originally Posted by jimer1964

Hi heater vents,are they the blue ones you have listed in the other post? Looking for some blue ones. Thanks

Ok let me know if and when you come across some nice blue vents. Thanks

[randy7426]

Originally Posted by specialtyretail

No problem. Thanks, Fred.

Hello how much for grille what kind of shape

[sherm6413]

How are the doors? Especially the passenger door...

[specialtyretail]

Originally Posted by sherm6413

How are the doors? Especially the passenger door...

Doors are in pretty good condition. Windows roll up and down and NO speaker holes. I can get you some pics Saturday. I really want to sell them as a pair if i can. Thanks, Fred.

[sherm6413]

How much for the pair and is there any rust through spots?

[specialtyretail]

Originally Posted by sherm6413

How much for the pair and is there any rust through spots?

SOLD,,,, THANKS.... Just went out and took some pics. The bottoms are not as nice as I thought. If you are interested, $200.00 for the pair with out the inner door panels. I cannot ship but can store them for a reasonable amount of time. Drivers side pics...

[specialtyretail]

SOLD,,,, THANKS.... Passenger side....

[sherm6413]

Thanks for checking, unfortunately that's not any better than what I have now, I'll have to pass

[1968k20]

What's the dash like near radio? I need a radio dash cut. Blue, if you have one.

[JimH2828]

Fred, is that a 350? Carb doesn't look like a 4bbl. I'm interested in top of the engine parts as I'm trying to correct mine.

- valve covers (with grommets, oil fill cap, bolts, hold downs)
- vacuum hard lines and manifold T
- gas pedal actuator with firewall mount and bolts
- throttle rode
- throttle springs
- throttle spring hook mount with bolt
- distributor hold down with bolt
- coil bracket with bolts
- trans kick down cable, bracket and bolts
- spark wire stands
- thermostat elbow with bolts

Thanks
Jim

[specialtyretail]

Originally Posted by JimH2828

Fred, is that a 350? Carb doesn't look like a 4bbl. I'm interested in top of the engine parts as I'm trying to correct mine.

- valve covers (with grommets, oil fill cap, bolts, hold downs)
- vacuum hard lines and manifold T
- gas pedal actuator with firewall mount and bolts
- throttle rode
- throttle springs
- throttle spring hook mount with bolt
- distributor hold down with bolt
- coil bracket with bolts
- trans kick down cable, bracket and bolts
- spark wire stands
- thermostat elbow with bolts

Thanks
Jim

Hey Jim. I think it is a 307. It has a two barrel carb. It is a three on the tree so I cannot help you with the trans kick down. I can't take the parts you are needing off just yet, I still need it to be driveable. How quick are you needing these parts? Thanks, Fred.

[specialtyretail]

Originally Posted by JimH2828

Fred, is that a 350? Carb doesn't look like a 4bbl. I'm interested in top of the engine parts as I'm trying to correct mine.

- valve covers (with grommets, oil fill cap, bolts, hold downs)
- vacuum hard lines and manifold T
- gas pedal actuator with firewall mount and bolts
- throttle rode
- throttle springs
- throttle spring hook mount with bolt
- distributor hold down with bolt
- coil bracket with bolts
- trans kick down cable, bracket and bolts
- spark wire stands
- thermostat elbow with bolts

Thanks
Jim

Hey Jim. Let me know if you are still needing these parts. I understand if you have already got them from somebody else, kind of had a health issue with the wife and was tied up for a bit. Thanks, Fred.

[JimH2828]

oh yeah, 3 on the tree, you mentioned that. No rush......whenever.

Thanks
Jim