exhaust maniflold stove shield wanted - The 1947 - Present Chevrolet & GMC Truck Message Board Network

Dean · 09-17-2003, 09:22 AM

I need the sheet metal stove shield that goes over the original exhaust manifold. A metal pipe then connects it to the air cleaner. I have the pipe but the part on the exhaust manifold it to far gone. This is for a V8 4 barrel truck. Anyone have one or know where I can get one? Thanks in advance!

Dean · 09-19-2003, 02:46 PM

anyone? ideas?

sactoC10 · 09-19-2003, 02:56 PM

I just pulled mine off last week, tossed the shield... and the garbage pickup day is today...I am at work and I am sure it is too late. Sorry man!

**smitty62** · 09-19-2003, 02:58 PM

I made mine out of 24 gauge stainless steel. If you want, any sheet metal man (home heating and air installer)? can cut you one if you can find one to copy. Use a small piece of the right size tailpipe for the tube connector, weld it on the inside where it doesn't show.

Dean · 09-19-2003, 03:31 PM

I may have to make one. I was hoping someone went to headers and has one laying around. There is almost nothing left of my original one.

Dean · 09-23-2003, 07:45 AM

Here are a few pics of the stove I am looking for. These are on my old Jimmy, but to far gone to use. Nothing like being in the rust belt.....

Dean · 09-23-2003, 07:45 AM

another.

09-17-2003, 09:22 AM	#1
Dean Senior Member Join Date: Jan 2000 Location: Cincinnati, Ohio Posts: 1,492	exhaust maniflold stove shield wanted I need the sheet metal stove shield that goes over the original exhaust manifold. A metal pipe then connects it to the air cleaner. I have the pipe but the part on the exhaust manifold it to far gone. This is for a V8 4 barrel truck. Anyone have one or know where I can get one? Thanks in advance!

09-19-2003, 02:56 PM	#3
sactoC10 71 DELUX Join Date: Sep 2003 Location: Northern CA / Sac Posts: 1,055	day late...dollar short I just pulled mine off last week, tossed the shield... and the garbage pickup day is today...I am at work and I am sure it is too late. Sorry man!

09-19-2003, 02:58 PM	#4
smitty62 Registered User Join Date: May 2002 Location: North Carolina Posts: 1,234	I made mine out of 24 gauge stainless steel. If you want, any sheet metal man (home heating and air installer)? can cut you one if you can find one to copy. Use a small piece of the right size tailpipe for the tube connector, weld it on the inside where it doesn't show. __________________ Stepsides look like real trucks! Smitty

09-23-2003, 07:45 AM	#6
Dean Senior Member Join Date: Jan 2000 Location: Cincinnati, Ohio Posts: 1,492	Here are a few pics of the stove I am looking for. These are on my old Jimmy, but to far gone to use. Nothing like being in the rust belt..... Attached Images

09-23-2003, 07:45 AM	#7
Dean Senior Member Join Date: Jan 2000 Location: Cincinnati, Ohio Posts: 1,492	another. Attached Images

09-19-2003, 02:46 PM	#2
Dean Senior Member Join Date: Jan 2000 Location: Cincinnati, Ohio Posts: 1,492	anyone? ideas?

09-19-2003, 03:31 PM	#5
Dean Senior Member Join Date: Jan 2000 Location: Cincinnati, Ohio Posts: 1,492	I may have to make one. I was hoping someone went to headers and has one laying around. There is almost nothing left of my original one.

Thread Tools
Show Printable Version Email this Page
Display Modes
Switch to Linear Mode Hybrid Mode Switch to Threaded Mode



Register or Log In To remove these advertisements.

Register or Log In To remove these advertisements.