The 1947 - Present Chevrolet & GMC Truck Message Board Network







Register or Log In To remove these advertisements.

Go Back   The 1947 - Present Chevrolet & GMC Truck Message Board Network > 47 - Current classic GM Trucks > The 1967 - 1972 Chevrolet & GMC Pickups Message Board

Web 67-72chevytrucks.com


Reply
 
Thread Tools Display Modes
Old 11-03-2016, 09:54 PM   #1
Braker68
Registered User
 
Join Date: Mar 2016
Location: Houston, Texas
Posts: 32
Gauge Cluster Questions for a 68 c10

Hello,
I have a few questions about the gauge cluster. I would like to use the old school gauge clusters that have the tach in the middle (like in the picture below). Is there anyway that I could use that type of gauge with a LS swap engine? Do I have to buy special adapters so that the cluster can work with the LS engine?
Attached Images
 
Braker68 is offline   Reply With Quote
Old 11-03-2016, 10:04 PM   #2
69chevy lwb
Registered User
 
69chevy lwb's Avatar
 
Join Date: Mar 2012
Location: Evanston
Posts: 304
Re: Gauge Cluster Questions for a 68 c10

You will need to spend a little time rounding everything up. I Used the autometer adapters for the coolant and oil line. The coolant sender will have to be aftermarket and then use a potentiometer to dial in your gauge then measure that resistance and match it with resistors. Then add a 10k resistor between the tachometer signal wire and key on power the ls doesn't have enough power to run it without. The stock speedometer might need a adapter to convert the mechanical gauge to receive an electronic signal. I think that pretty well covers anything but let me know if you need anymore information.
69chevy lwb is offline   Reply With Quote
Old 11-03-2016, 11:52 PM   #3
LockDoc
The Older Generation


 
LockDoc's Avatar
 
Join Date: Aug 2006
Location: Montezuma, Iowa
Posts: 25,773
Re: Gauge Cluster Questions for a 68 c10

Yes, but you will need an adapter like this...

http://www.summitracing.com/parts/ATM-2268/

to screw into your LS block where the original oil sender is, or you can remove the original LS sender, break the plastic off of it and drill and tap it to 1/8" NPT thread and use the original '68 oil line block fitting. (as shown in the first picture)

On the temp sender I drilled the head out to accept the original '67-'72 gauge sender. You use a 23/32 bit ( I started out small and worked my way up) and a 1/2-14 NPT tap, and use the correct sensor for your gauge or light.

LockDoc
Attached Images
  
__________________
Leon

Locksmith, Specializing In Antique Trucks, Automobiles, & Motorcycles

(My Dually Pickup Project Thread)

http://67-72chevytrucks.com/vboard/s...d.php?t=829820

-

Last edited by LockDoc; 11-04-2016 at 12:33 AM.
LockDoc is offline   Reply With Quote
Old 11-04-2016, 09:30 AM   #4
jsera
Registered User
 
Join Date: Oct 2014
Location: Orlando, FL
Posts: 165
Re: Gauge Cluster Questions for a 68 c10

Depends if the trans your using uses vss for speedo. The original gauges use a cable driven speedo where modern vehicles are electronic
jsera is offline   Reply With Quote
Old 11-04-2016, 05:26 PM   #5
LockDoc
The Older Generation


 
LockDoc's Avatar
 
Join Date: Aug 2006
Location: Montezuma, Iowa
Posts: 25,773
Re: Gauge Cluster Questions for a 68 c10

Quote:
Originally Posted by jsera View Post
Depends if the trans your using uses vss for speedo. The original gauges use a cable driven speedo where modern vehicles are electronic

I bought a Dakota Digital Speedometer converter for my '67 Panel Truck so I could use my stock speedometer and it works great. For my '67 LWB pickup when I put the S-10 5 speed behind the I-6, I bought a GPS speedometer from Speedhut Co. ( http://www.speedhut.com/ ) and it works great also....

LockDoc
__________________
Leon

Locksmith, Specializing In Antique Trucks, Automobiles, & Motorcycles

(My Dually Pickup Project Thread)

http://67-72chevytrucks.com/vboard/s...d.php?t=829820

-
LockDoc is offline   Reply With Quote
Old 11-04-2016, 11:12 AM   #6
michael bustamante
Senior Member
 
michael bustamante's Avatar
 
Join Date: Sep 2007
Location: Albuquerque NM
Posts: 7,862
Re: Gauge Cluster Questions for a 68 c10

subbed
__________________
1967custom
michael bustamante is offline   Reply With Quote
Reply

Bookmarks

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -4. The time now is 11:19 PM.


Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2024, vBulletin Solutions Inc.
Copyright 1997-2022 67-72chevytrucks.com