|
|
|
11-16-2016, 11:10 AM
|
#1 |
|
Senior Member
 
Join Date: Jun 2015
Location: Atlanta, GA.
Posts: 737
|
Headlight Buckets
1985 Custom Deluxe LWB.
I have taken my front end apart and started painting and powder coating. All has gone well and it's going back together and I'm up to the Headlight Buckets. GM did not think too much of these as they are NOT stamped with a part number or any kind of marking??? I assume they are original as everything else in the front of the truck was. (Grill, core support, valance panel, etc.) As pictured, these are different in the clocking of the tabs in the back. (see pics, one installed, three waiting) And because this is the one time I did not take a hundred photos before taking it apart, I have no idea which one is high beam vs low beam or Left vs Right? I do have the Quad Headlight front end so there are 2 with the tabs at 2:00 and 8:00 and 2 with the tabs at 10:00 and 4:00. Can anyone post some pics of their Quad Headlight set up so I can figure out which one goes where? Thanks in advance
__________________
Jay Gesner Atlanta, GA 1985 C10 Long Bed 4X2 LS 5.3, 4L60E Father/Daughter Project |
|
|
|
11-16-2016, 11:12 AM
|
#2 |
|
Senior Member
Join Date: Jun 2015
Location: Atlanta, GA.
Posts: 737
|
Re: Headlight Buckets
Here are the pics
__________________
Jay Gesner Atlanta, GA 1985 C10 Long Bed 4X2 LS 5.3, 4L60E Father/Daughter Project |
|
|
|
|
11-17-2016, 02:58 PM
|
#3 |
|
Senior Member
Join Date: Jun 2015
Location: Atlanta, GA.
Posts: 737
|
Re: Headlight Buckets
If someone could take a pic of the back of the core support, that would help too. Just as long as it shows the orientation of the headlight buckets.
Thanks, Jay
__________________
Jay Gesner Atlanta, GA 1985 C10 Long Bed 4X2 LS 5.3, 4L60E Father/Daughter Project |
|
|
|
|
11-17-2016, 05:41 PM
|
#4 |
|
Registered User
Join Date: Jun 2016
Location: Phoenix, AZ
Posts: 574
|
Re: Headlight Buckets
It should be fairly easy - look at where the adjusters are. They really only fit one way.
|
|
|
|
|
11-18-2016, 12:17 PM
|
#5 |
|
Senior Member
Join Date: Jun 2015
Location: Atlanta, GA.
Posts: 737
|
Re: Headlight Buckets
yeah, I did that and figured out left from right. however, each set for left and right have different tabs in the back. (where the plug goes) One at 10:00 and 4:00-the other two at 2:00 and 8:00.
So which one is for the high beam and which one is for the low beam? They fit in each place on the core support and both headlight bulbs fit in each bucket. It is very UN-like GM to make them different without some kind of reason. The only thing I can think of that makes difference in that area is the headlight plug itself. I just don't want to put these in only to later discover why and have to take them out again. I hate rework.
__________________
Jay Gesner Atlanta, GA 1985 C10 Long Bed 4X2 LS 5.3, 4L60E Father/Daughter Project |
|
|
|
|
11-18-2016, 09:02 PM
|
#6 |
|
Registered User
Join Date: Sep 2009
Location: Beaverton, OR from WA State
Posts: 1,515
|
Re: Headlight Buckets
According to the parts manual:
5966080 - LH Upper 5966081 - RH Upper 5966082 - LH Lower 5966083 - RH Lower There are multiple pics of each one on ebay, should be able to narrow it down.
__________________
Devin 1983 GMC High Sierra 2500, 4x4, RC/LB, 400 S.B., SM-465, NP-208, Corporate 10 bolt & 9.5" 14 bolt 1996 GMC Sierra SLE 3500 DRW, 4x4, EC/LB, Vortec 454, NV-4500, BW-4401, AAM 925 & AAM 1050 1997 GMC Sierra SLT 1500 4x4, Z71/F44, EC/SB, Vortec 350 My Introduction with my '83s History New Daily, the '96 |
|
|
|
 |
| Bookmarks |
| Thread Tools | |
| Display Modes | |
|
|
Hybrid Mode
