my 1988 GMC 7000 dump truck story

[sweetk30]

1988 gmc 7000 bbc air cleaner tag shows 454 7.4L looks like spicer 5 speed tranny with 2 speed rear and full air brakes and air control on rear for trailer.

vin # 1gdm7d1b5jv520621

story is its got bad motor . said it over heated a few times and has not been correct since then . I pulled the fuel tank cap and the gas smells funky and the window reg shows good till 2015 . . so I know she has been sitting for prob 2+ years now inop .

she is low miles 50-60k range from what I was told ( forget to read my self ) but the frame / cab / dump box are in premo condition if you gave it a good wash you could eat off them . frame rails almost all original paint still there .

truck is from the south original and I think it prob had water in the cooling system only ( seen lots of them like this ) and she prob boiled over and or froze the block and cooked its self .

I have a good 454 from a 79 suburban with 60k miles on it and run good on way home with few flat cam lobs . . just need cam and gaskets . was thinking swap this in place of its dead 454 . . . or even find a 8.1 big block with efi and drop in .

what do you think it would be worth in its current state ? keep in mine I am in the heavy rust belt of the north east and clean ones like this are super rare to find . . .

I can buy it for less than the dump box is worth used pull off. so worst case I flip the box and have a free truck .

was planning on making a big boy toy with it .

thanks for any input guys and as always have a good day

[C10 - C90 Bill]

Nice looking truck.

If the price is right, like it sounds like it is, I would grab it, especially since you have another engine to drop in there.

Keep us posted on it.

[bigrigpardo]

well I am in north nj and I cant say I have seen many as clean as you say it is but a truck like that sitting that long with a bad motor I would say 1500. the retail market on these trucks is not that high anymore from what I see. I had a guy with a fully operational on the road truck that he got 2000 for now it wasn't perfect rust free but fully serviced and road legal. grab it cheap sell the box and make a big boy pickup out of it.

[sweetk30]

so I got the title today on this old girl . . . cost me 1600 bucks but she has 1 clean frame and body and dump box .

just got to wait for the snow/ice to melt off the dirt road to the top of the hill were its parked and then the boss and I can go get it with the BIG tow truck .

[flashed]

Im in to see what you do with this Biggin.

[dwcsr]

Originally Posted by sweetk30

1988 gmc 7000 bbc air cleaner tag shows 454 7.4L looks like spicer 5 speed tranny with 2 speed rear and full air brakes and air control on rear for trailer.

vin # 1gdm7d1b5jv520621

story is its got bad motor . said it over heated a few times and has not been correct since then . I pulled the fuel tank cap and the gas smells funky and the window reg shows good till 2015 . . so I know she has been sitting for prob 2+ years now inop .

she is low miles 50-60k range from what I was told ( forget to read my self ) but the frame / cab / dump box are in premo condition if you gave it a good wash you could eat off them . frame rails almost all original paint still there .

truck is from the south original and I think it prob had water in the cooling system only ( seen lots of them like this ) and she prob boiled over and or froze the block and cooked its self .

I have a good 454 from a 79 suburban with 60k miles on it and run good on way home with few flat cam lobs . . just need cam and gaskets . was thinking swap this in place of its dead 454 . . . or even find a 8.1 big block with efi and drop in .

what do you think it would be worth in its current state ? keep in mine I am in the heavy rust belt of the north east and clean ones like this are super rare to find . . .

I can buy it for less than the dump box is worth used pull off. so worst case I flip the box and have a free truck .

was planning on making a big boy toy with it .

thanks for any input guys and as always have a good day

this most likely has a tall deck BBC and your 79 454 is a short deck meaning the accessories will not fit

[sweetk30]

ya I know.

vin decode shows 6.0 366

but seemed funny I swear I saw 7.4 on air cleaner tag . . . was blowing 20+mph and 10* out the day I walked up the hill to look it over.

if need be I have a line on a 427 tall deck motor currently running .

[b454rat]

I keep hearing bout a tall deck 454, but never seen one. I've been to a couple yards that had a billion of these over the years, nothing. 6 bangers, 350s, 366, 427 but no '54s. I haven't found another 8.1 either...guess I got lucky with mine!!!

[rkn463]

Great looking truck. Show us some interior shots when you get a chance.

Regarding the motor I've been trying to find out if the crate 502 or 572 are tall deck motors. With the 572 it would need lower compression pistons and a truck minded cam to be worthwhile, but it sure would be nice to be back in to the high torque numbers. I think my duramax spoiled me 😀

-Richard

[b454rat]

Believe 502 is standard deck and 572 is tall....

[rkn463]

Originally Posted by b454rat

Believe 502 is standard deck and 572 is tall....

That is good info, thanks.

[sweetk30]

if I decide to keep it and make a big boy toy out of it . . .

I was planning military 5ton axles that come with air brake . and also the 5ton transfer case as high range is .7xx over drive to help over come the 6.44:1 axle gear combo . plan on a 46-48" tall tire combo also .

just a few ideas kicking around in my head.

[sweetk30]

got back there today and plowed the road up to the truck so I get it towed out by the end of the week when the road is melted off for the BIG tow truck to get up there .

vin decode and air cleaner tag show 366 engine. . . but air cleaner tag shows 7.4 also . searching internet this seems to have been a common thing .

I got a idea tho . I have a line of a 8.1 big block complete take out . this would be a great repower for it and its from a med duty truck already .

gvw on the tag on the side of the cab door frame 9000k frt / 19000k rear / total 28k gvw truck .

glove box had 2 FULL rpo code sheets in it.

showed :
038 / 6.57 ratio rear
fxv / 149 inch wheel base
gyh / aux rear springs
kra / engine gov 3800

way to many to list up . . .

anyone got a good rpo code brake down list ?

[rkn463]

Originally Posted by sweetk30

way to many to list up . . .

anyone got a good rpo code brake down list ?

I can take a shot of a list I have and post it later this evening.

-Richard

[ryanv70c10]

Originally Posted by b454rat

Believe 502 is standard deck and 572 is tall....

GM made a tall deck 427 for the trucks

[sweetk30]

well here was the hill / farm path up to the trucks parking spot this am . . I even went up yesterday and dumped 150lbs of salt down it didn't do hardly squat .

the tow guy backed up to the truck . 1st attempt up hill failed . . but second was a winner .

hooked it / chained it / strapped the steering wheel and away we went .

he did say she has tight steering as most every thing he pulls wanders all over in the back . but my dump was straight as a arrow.

[sweetk30]

also got to looking at the parts truck next to it .

its a 7000 model also with factory diesel .

I noticed it has a power steering box with 2 extra hose ports that go to a hydro ram that's bolted to the left frame rail / special pitman arm .

would this be something I might wana grab for a price ? incase I want beffyer steering if I go 4x4 conversion with 5 ton military axles ?

[rkn463]

Originally Posted by sweetk30

also got to looking at the parts truck next to it .

its a 7000 model also with factory diesel .

I noticed it has a power steering box with 2 extra hose ports that go to a hydro ram that's bolted to the left frame rail / special pitman arm .

would this be something I might wana grab for a price ? incase I want beffyer steering if I go 4x4 conversion with 5 ton military axles ?

If you already have power steering it is pretty beefy. I went and looked at your first post, is that the parts truck right beside it? Does it have a tilt front end? If so that is what I'd be after! And what diesel does it have?

-Richard

[sweetk30]

yes I have p/s but my thinking was for the 5ton military axle swap if I keep it and make a big boy toy out of it . the extra ram would help turn the 48-53" tires I would run on it . some 5ton trucks in military have a ram on the pass side to help take load off the parts I have noticed .

and yes the other truck has the flip nose option and its a factory diesel that's hade lots of stuff pillaged off it already . the flip nose hood I tilted up to see was super floppy and the truck had a lot more wear / tear than mine . would it be worth a second look and if so what would it be worth for the front nose parts ? I know the rad is gone and a lot of its brackets / mounts .

I don't mind my hood only style that much . I am working on one currently and had to get in the pass side . I unbolted the inner fender and had tons of room inside.

[rkn463]

Originally Posted by sweetk30

yes I have p/s but my thinking was for the 5ton military axle swap if I keep it and make a big boy toy out of it . the extra ram would help turn the 48-53" tires I would run on it . some 5ton trucks in military have a ram on the pass side to help take load off the parts I have noticed .

and yes the other truck has the flip nose option and its a factory diesel that's hade lots of stuff pillaged off it already . the flip nose hood I tilted up to see was super floppy and the truck had a lot more wear / tear than mine . would it be worth a second look and if so what would it be worth for the front nose parts ? I know the rad is gone and a lot of its brackets / mounts .

I don't mind my hood only style that much . I am working on one currently and had to get in the pass side . I unbolted the inner fender and had tons of room inside.

I'm not sure what the tilt hood and core support would bring. I do know that working on my brother's dump truck of that style, climbing up and down all day got really old. We swapped a school bus engine into his dump truck, the bus had the tilt front and the used the same radiator.

I checked the factory service manual and the steering setup that you are describing is called semi-integral and came on the 12,000 pound front axle trucks.

-Richard

[deejaaa1]

tuned in. like where this is going.

[sweetk30]

so if I was to go a big crazy and old school . . . .

would a 6v53 from a gradall grader be a basic bolt in ?

I found one local with engine / trans / rad from said unit with just under 1k hrs on it for 2k cash .

I have always loved the sound of a screemin Detroit and yes I know there NOISEY . I have a 2 stroke atv already so I am use to the sound.

I know the med duty stuff use to get these in them . just not sure if my 88 would be basicly equipped for it tranny wise / bellhousing stuff.

I can fab stuff for mounts and such easy .

[Bigasstrux]

Medium duty GM trucks used the 453T as the only two stroke available.

[sweetk30]

well i am crazy or lucky will see soon .

2nd ebay used engine . but this one looks real good and he gave me extra pics i asked for and info he posted and gave me also is way above the normal sellers level of a used engine .

remaned for gm tag on the block . under 10k miles he said . fogged before shutdown and pulled . rockers backed off so no pressure on springs or lifters .

should be here mid week next week .

[sweetk30]

just got my pics of the engine all ready to ship out for my truck . this seller has done a super job on dealing with me .