Tilt column light for gear indicator

[hdff]

I have a 71 with a tilt column, don't know if it is stock to the truck. The light under the gear indicator on the column wasn't working so today I attempted to fix it. Well there wasn't a bulb in it, so off the the parts house to try to find ont that will work. Found one that fit the socket but was to long. But tried it to see it it would work, no luck... does anyone know what size bulb fits and where the power wire is. I would like to get it working, I'm anal about things like that. Any help would be greatly appreciated..

[chiefcfd]

The power wire should be grey and plug in the fuse panel. I think it plugs into "panel light" spade. I don't know the bulb number. It is part of the Turn signal switch.

[FirstOwner69]

Originally Posted by chiefcfd

The power wire should be grey and plug in the fuse panel. I think it plugs into "panel light" spade. I don't know the bulb number. It is part of the Turn signal switch.

Not true for the tilt columns.

Tilts use #1445 bulbs along with the other 2 parts in the attached picture placed under the gear indicator as hdff stated in post 1.

The gray light wire plugs onto the "PNL LTS" spade on the fuse block as I recall. I can confirm that tomorrow.

[chiefcfd]

Originally Posted by FirstOwner69

Not true for the tilt columns.

Tilts use #1445 bulbs along with the other 2 parts in the attached picture placed under the gear indicator as hdff stated in post 1.

The gray light wire plugs onto the "PNL LTS" spade on the fuse block as I recall. I can confirm that tomorrow.

I'm confused FirstOwner, other than the Bulb number that's exactly what I said. The bulb socket is part of the TSS.

[hdff]

Originally Posted by chiefcfd

The power wire should be grey and plug in the fuse panel. I think it plugs into "panel light" spade. I don't know the bulb number. It is part of the Turn signal switch.

Originally Posted by FirstOwner69

Not true for the tilt columns.

Tilts use #1445 bulbs along with the other 2 parts in the attached picture placed under the gear indicator as hdff stated in post 1.

The gray light wire plugs onto the "PNL LTS" spade on the fuse block as I recall. I can confirm that tomorrow.

Thanks, I'll go get a 1445 bulb today and look for the gray wire at the column . I have the silver domed piece but not the green piece, and I assume it is not sold aftermarket, does it go inside the silver domed piece? Does the gray wire go direct from the column to the fuse block or tie into the wire harness with the rest of the panel lights?

[FirstOwner69]

Originally Posted by chiefcfd

I'm confused FirstOwner, other than the Bulb number that's exactly what I said. The bulb socket is part of the TSS.

Oops, sorry about that. For some reason when I read that last night it registered that you were saying it plugged into the cluster like the non-tilts do. It was very late, but I hadn't been drinking anything but water. Must be old age like these trucks! Go figure.

Originally Posted by hdff

Thanks, I'll go get a 1445 bulb today and look for the gray wire at the column . I have the silver domed piece but not the green piece, and I assume it is not sold aftermarket, does it go inside the silver domed piece? Does the gray wire go direct from the column to the fuse block or tie into the wire harness with the rest of the panel lights?

The green "filter" goes over the end of the dome. I don't think they are available. I have a 30 year old bottle from J.C Whitney of what was called green bulb dye if I recall correctly. It looks like green nail polish, but I don't know if nail polish would hold up to the bulb heat. That would provide the same green tint as the filter.
EDIT: I found this on eBay. http://www.ebay.com/itm/Pebeo-Vitrea...QAAOSw6WdXie7o. It says it should be baked in an oven after application. I bet the heat of the bulb would bake it. Various shades of green are available. I searched for "green glass paint". It looks like Texas Art Supply stores in the Houston area may also sell this paint.

[hdff]

Originally Posted by FirstOwner69

Oops, sorry about that. For some reason when I read that last night it registered that you were saying it plugged into the cluster like the non-tilts do. It was very late, but I hadn't been drinking anything but water. Must be old age like these trucks! Go figure.



The green "filter" goes over the end of the dome. I don't think they are available. I have a 30 year old bottle from J.C Whitney of what was called green bulb dye if I recall correctly. It looks like green nail polish, but I don't know if nail polish would hold up to the bulb heat. That would provide the same green tint as the filter.
EDIT: I found this on eBay. http://www.ebay.com/itm/Pebeo-Vitrea...QAAOSw6WdXie7o. It says it should be baked in an oven after application. I bet the heat of the bulb would bake it. Various shades of green are available. I searched for "green glass paint". It looks like Texas Art Supply stores in the Houston area may also sell this paint.

looking on line I found a LED bulb with that base that comes in green, I may try that if I can find the wire coming out of the column and see if it is hot. I had a minute for a quick look today and there is a gray wire hooked up to the inst prong on the fuse block bit I didn't see where they came out of the column. i'll have to look when I have more time

[hdff]

Originally Posted by FirstOwner69

Not true for the tilt columns.

Tilts use #1445 bulbs along with the other 2 parts in the attached picture placed under the gear indicator as hdff stated in post 1.

The gray light wire plugs onto the "PNL LTS" spade on the fuse block as I recall. I can confirm that tomorrow.

Well I looked for a gray wire coming out with the column wire harness, didn't see one so I assume the PO might have cut it for some reason. Firstowner can you tell me what this black wire with a metal end is? It looks like it comes out of the tape that is around the column wire harness.

[70shortfleet]

The black wire is a fiber optic line for a non tilt automatic column, Don't know why it would be there if you had a tilt column?

[hdff]

Originally Posted by 70shortfleet

The black wire is a fiber optic line for a non tilt automatic column, Don't know why it would be there if you had a tilt column?

hummm, it's a tilt wheel so I don't know why it's there and not a gray one for the light under the gear indication

[old51sedan]

Originally Posted by hdff

Well I looked for a gray wire coming out with the column wire harness, didn't see one so I assume the PO might have cut it for some reason. Firstowner can you tell me what this black wire with a metal end is? It looks like it comes out of the tape that is around the column wire harness.

I just pulled the non tilt column out of my 69 to replace with a new repo tilt column. The wire you have in question is the same as the one on my original column. It is fiber optic and mine was attached to the dash light that is plugged in on the right hand side of the speedometer. I unplugged it as it was hooked to the original column and will plug the new column wire into the fuse panel.

[hdff]

Originally Posted by old51sedan

I just pulled the non tilt column out of my 69 to replace with a new repo tilt column. The wire you have in question is the same as the one on my original column. It is fiber optic and mine was attached to the dash light that is plugged in on the right hand side of the speedometer. I unplugged it as it was hooked to the original column and will plug the new column wire into the fuse panel.

the weird thing is there is a bulb socket at the gear indicator at the top of the column and if it was fiber optics I don't think it would have a place for a bulb