Distributor hold down - The 1947 - Present Chevrolet & GMC Truck Message Board Network

skokie · 11-22-2003, 10:38 PM

Can you use the same hold down clamp for a hei distributor from a points distributor? The one I am using does not lock it down completely.

Thanks

*rage'nrat638* · 11-22-2003, 10:39 PM

SAME......SAME ONE

skokie · 11-22-2003, 10:42 PM

Then I must be doing something wrong. Do you need to lift it any higher on the distributor?

jorgensensc · 11-22-2003, 10:44 PM

Your clamp might be bent straight. I suggest going to auto parts store and buy a 5.00 chrome one.

*rage'nrat638* · 11-22-2003, 10:45 PM

is the flange on the dist. shaft flush with the engine...????

setted all the way in???

skokie · 11-23-2003, 02:28 AM

Yep its all the way in. It looks like this dist doesnt have as thick as a circle around it as the points one did. That may be why.

bigjimzlll · 11-23-2003, 02:38 AM

flip your hold down over

shuttermutt · 11-23-2003, 03:12 AM

...and make sure the bolt isn't bottoming out.

skokie · 11-23-2003, 03:15 AM

I will try flipping it over tomorrow. Maybe that will work.
Thanks

11-22-2003, 10:38 PM	#1
skokie Registered User Join Date: Oct 2003 Location: San Jose Ca. Posts: 3,342	Distributor hold down Can you use the same hold down clamp for a hei distributor from a points distributor? The one I am using does not lock it down completely. Thanks Last edited by skokie; 11-22-2003 at 10:41 PM.

11-22-2003, 10:44 PM	#4
jorgensensc Registered User Join Date: Jul 2003 Location: Cypress, Tx Posts: 4,005	Your clamp might be bent straight. I suggest going to auto parts store and buy a 5.00 chrome one. __________________ 1972 C20 Suburban- Big Blue Betty '56 Chevy Bel Air Sedan- Frame up Restoration -What would you attempt to achieve if you knew you could not fail?- -I Refuse To Tiptoe Through Life, Only To Arrive Safely At Death's Door- R.I.P. EAST SIDE LOW LIFE

11-23-2003, 02:38 AM	#7
bigjimzlll Senior Member Join Date: Dec 2001 Location: Redding,CA...USA Posts: 4,736	flip your hold down over __________________ It's called "drag racing" if they called it "tic..tic..WHAM!..BANG! F*&K!!!", they'd have to keep the magazines under the counter with the other men's publications click the clicky to join the site.... http://67-72chevytrucks.com/vboard/payments.php 67 lwb..first hotrod in 25 years..540 best ET is 9.45 @ 141.44 Anderson,CA

11-23-2003, 03:12 AM	#8
shuttermutt Don't say "Oops!", Doctor Join Date: Nov 2003 Location: Houston, TX Posts: 677	...and make sure the bolt isn't bottoming out. __________________ 'Mutt 1968 CST LWB: R.I.P. 1967 Chevelle: TPI 454 beast 1967 C10 SWB: Claimed when Bumpster didn't put it on his list

Thread Tools
Show Printable Version Email this Page
Display Modes
Switch to Linear Mode Hybrid Mode Switch to Threaded Mode

11-22-2003, 10:39 PM	#2
rage'nrat638 Account Suspended Join Date: Mar 2003 Location: THE FALL GUY CHICAGO IL Posts: 5,883	SAME......SAME ONE

11-22-2003, 10:42 PM	#3
skokie Registered User Join Date: Oct 2003 Location: San Jose Ca. Posts: 3,342	Then I must be doing something wrong. Do you need to lift it any higher on the distributor?

11-22-2003, 10:45 PM	#5
rage'nrat638 Account Suspended Join Date: Mar 2003 Location: THE FALL GUY CHICAGO IL Posts: 5,883	is the flange on the dist. shaft flush with the engine...???? setted all the way in???

11-23-2003, 02:28 AM	#6
skokie Registered User Join Date: Oct 2003 Location: San Jose Ca. Posts: 3,342	Yep its all the way in. It looks like this dist doesnt have as thick as a circle around it as the points one did. That may be why.

11-23-2003, 03:15 AM	#9
skokie Registered User Join Date: Oct 2003 Location: San Jose Ca. Posts: 3,342	I will try flipping it over tomorrow. Maybe that will work. Thanks



Register or Log In To remove these advertisements.