![]() |
|
![]() |
#1 |
Registered User
Join Date: Jan 2014
Location: Wacousta, Mich
Posts: 90
|
Lowered Ride question
Just finished my 72 project, lowered 4-6 with Western Chassis parts. (not good quality in my opinion)
Front is 2'' spring and 2 1/2 spindle Rear is 4'' Spring and 2" block with adjustable panhard Alignment is done and drives great down the road, issue is when rear hits small bumps it feels like there are no shocks on the truck. Almost get 2 bumps for 1. Better shocks? wrong set up in rear? Front seems to ride and handle very nice. Any help is greatly appreciates> |
![]() |
![]() |
![]() |
#2 |
Registered User
Join Date: Mar 2005
Location: 10-Uh-See
Posts: 5,609
|
Re: Lowered Ride question
What shocks do you have? correct length shocks are important when lowering any vehicle. If the shock angle is off, or the shock is compressed too much, it can bottom out and have a heavy "bounce back" type of rebound.
__________________
|
![]() |
![]() |
![]() |
#3 |
Senior Member
![]() Join Date: Jun 2009
Location: Portland - OR
Posts: 243
|
Re: Lowered Ride question
How close are your bump stops? You may not have much travel.
|
![]() |
![]() |
![]() |
#4 |
Registered User
Join Date: Jan 2014
Location: Wacousta, Mich
Posts: 90
|
Re: Lowered Ride question
Shocks were ordered with the kit I have not measured exact length yet.
I cut bump stops in half, and still no difference. I did not c the frame I believe I have enough travel. The shocks were too short to hook up until I put box on the truck however. |
![]() |
![]() |
![]() |
#5 |
Registered User
Join Date: Jan 2014
Location: Wacousta, Mich
Posts: 90
|
Re: Lowered Ride question
I did use a shock relocation kit as well so they are at the right angle according to them. They are Western DS-2 shocks
|
![]() |
![]() |
![]() |
#6 |
Registered User
Join Date: Jan 2016
Location: Sugar Hill GA
Posts: 369
|
Re: Lowered Ride question
I have 4 inch Belltech springs but only 1 inch blocks. I did not cut the bump stops I am running Belltech Street Performance shocks S2208 with shock relocators and have no suspension issues. Those 2 inch blocks might be too much for the shocks you have.
__________________
1967 C10 Step side 1970 AMX 390 1977 Datsun 280Z highly modified with '95 LT1 power |
![]() |
![]() |
![]() |
#7 |
Registered User
![]() Join Date: Nov 2006
Location: KINGSPORT,TN.
Posts: 3,035
|
Re: Lowered Ride question
Get use to it also you,ll go thru a hanger bearing a year
__________________
I BELIEVE IN JOHN 3:16 |
![]() |
![]() |
![]() |
#8 |
Registered User
Join Date: Jan 2014
Location: Wacousta, Mich
Posts: 90
|
Re: Lowered Ride question
So your saying its just the way it will ride ? And whats the hanger bearing comment about ?
|
![]() |
![]() |
![]() |
#9 | |
Registered User
Join Date: Mar 2005
Location: 10-Uh-See
Posts: 5,609
|
Re: Lowered Ride question
Quote:
As for the shocks, measure the distance from eye to eye AT RIDE HEIGHT, then jack it up, unbolt the shocks and measure again with the wheels off the ground. Then, put it on jackstands, use a tie down strap between the rearend and frame and completely bottom out the springs. Write all these measurements down. Now, with the shocks out, measure them at full extension. Then, compress them and measure compressed(you may need a helper for this). Write these down also. Here's where simple math comes into play. compare the differences of full suspension drop vs. full shock extension, then full suspension compression vs. full shock compression. See how far these numbers are off to determine if the shocks are within a tolerable operating range. I did this a few years ago on my setup and found out the shocks were way out of range. The problem you'll run into, though, is that shock companies don't offer shocks by dimensions, only vehicle specific part numbers. That leaves limited options. Option 1: Leave it alone and deal with bad ride quality. Option 2: Take your measurements to a parts store and see if they'll let you open boxes and find shocks that fit. This is very frowned on at chain stores since the shocks are either wired or banded to full compression for easy packaging. Option 3: Order "drop shocks" from somewhere like CPP, DJM, or McGaugheys, and hope they fix the issue. Option 4: Pony up the dough for a set of Ridetech HQ series shocks with the measurements you need. https://www.ridetech.com/products/sh...h-body-shocks/
__________________
|
|
![]() |
![]() |
![]() |
#10 |
Registered User
Join Date: Jan 2014
Location: Wacousta, Mich
Posts: 90
|
Re: Lowered Ride question
Thank you for the detailed information. I will get to work on this stuff immediately. I had concerns with length of a 1 piece driveshaft. I do need to check pinion angle for sure.
|
![]() |
![]() |
![]() |
#11 |
Registered User
Join Date: Aug 2010
Location: Orrtanna PA
Posts: 28
|
Re: Lowered Ride question
Also be careful that your shocks are not too short and basically not extending far enough when the suspension becomes unloaded. Just as bad of a ride if they were too long and bottoming out.
|
![]() |
![]() |
![]() |
#12 |
Registered User
![]() Join Date: Nov 2006
Location: KINGSPORT,TN.
Posts: 3,035
|
Re: Lowered Ride question
yes, the geometry is now way off in drive line
__________________
I BELIEVE IN JOHN 3:16 |
![]() |
![]() |
![]() |
#13 |
Senior Member
![]() Join Date: Feb 2010
Location: Falls City, Nebraska "100 Miles From Nowhere"
Posts: 2,219
|
Re: Lowered Ride question
Either C-notch your frame or lose the lowering blocks...That's "Option 5"
__________________
Michael of the clan Hill, "Two Seventy Two's" 71 1-ton Dually 350 4-Speed 71 C/50 Grain Truck, 350 Split-Axle 4-Speed 02 3/4 ton Express 14 Indian Chief Vintage 1952 Ford 8N, "Only Ford Allowed On The Property" ![]() "Be American, Buy American" ![]() |
![]() |
![]() |
![]() |
Bookmarks |
Thread Tools | |
Display Modes | |
|
|