What are your goals this year for your truck?

[70cst]

I want to get my truck out and start driving it. Sometimes life gets in the way and so it has with me for the last couple of years.
Its time to make tracks and play some Oldies Goldies...

I plan on installing the CB Radio and 8 track player.

[rharris]

Trade it for a Blazer or if I keep it a new long block and seat cover.

[tdangle]

I am hoping to get the body finished and painted. Otherwise just enjoy and drive it.

[Speedracer39]

Take the drive from the Midwest to the C10 nationals in Tx. After that just plan on enjoying it and possibly body work.

[35boulder]

Nothing more than routine maintenance and just enjoy driving it more!

[Gigem]

Truck should be back in my garage in a few weeks after it's successful heart transplant. I hope to be putting some miles on it soon. I've got a couple of cosmetic items I want to address, seat cover and replace missing passenger side eyebrow molding. Fix front right turn signal (see picture). Probably new tires and wheel center caps. Maybe start looking at AC. Maybe get rusted rocker panels replaced. That's about it...

[67C10Step]

I am way behind most of you. My rear brake parts are supposed to arrive tomorrow so first order is to get all new brake hardware installed.
Then I’ll flip it around in the shop and go to work on the front end. Install power steering and rebuild front end with disc brake swap. Install new brake lines and at that point it will be rough but roadworthy.

[70STOVEBOLT]

I would like to get it assembled so it’s road worthy and get some miles on the engine and trans, which I recently rebuilt myself. Then next fall get it ready for paint.

[PepperTreeGarage]

Finish the build.

[sfont66]

Rockers & cab corners, new carpet.
Last year a dock truck at work hit the side/ rear and did $3300 damage 😡so I will need to fix all that damage as well. Easy fix, but hate to work on the stuff that was not in need of attention.
I have been wanting a tremec tko600 5 speed or the T-56 magnum 6speed, but then again one can find a low mile 6.2 with TR-6060 out of a wrecked Camaro for not much more $. Then again I would love a big big block..... it’s a rabbit hole......Help

[70']

Finish the Frame off build (I am really close) then, detail it and just go out cruising on Friday and Saturday nights.

[Ben IV]

Go through the suspension lower it and cut it down to a short bed.

[Linz]

I’d like to get mine on route/in a container heading for home down in New Zealand I seem to always run out of time while I’m over there. I need to do some homework on all what’s involved in getting that done.

[rpmerf]

Find someone to balance the driveshaft to get rid of the vibration at 60 mph.

I got a new set of door / window seals for Christmas. While I have the doors apart, I might try to reinstall the camper mirrors.

Got a camping trip planned in May.

Finish custom dual battery wiring. Wire up 'Ignition On' fuse block.

[special-K]

Originally Posted by rpmerf

Find someone to balance the driveshaft to get rid of the vibration at 60 mph.

Westminster Transmission Service (410) 848-1429. Right behind the courthouses, 209 Greenwood Ave. Best shop for that. They do all my driveshaft work. They are drivetrain experts, front to back.
------------------------------------------------------------------------------------------------
Since I have a shelter built, I plan to move the '67 project in there and see if I can start doing things with that. Plans for the '72 are new exhaust system, maybe stick some music in there. I have a pair of door panels with 6 1/2" speakers in them and an AM/FM/Cassette.

[OldBlue70C10]

I just hope to get mine running finally, after 15 years of sitting under a tree.

[rpmerf]

Originally Posted by special-K

Westminster Transmission Service (410) 848-1429. Right behind the courthouses, 209 Greenwood Ave. Best shop for that. They do all my driveshaft work. They are drivetrain experts, front to back.

Thanks! I'll check them out. Bit of a drive for me, but worth it knowing they know what they are doing.

[70cst]

Great feedback - keep them coming.

[my04]

Paint this tailgate and then cruise all summer long!

[Furno68C20]

Remove the 327, do rebuild, take all the aftermarket crap off and go back to Factory. While doing that I’ll put my fresh built 350 in there to continue driving during the summer months.
Posted via Mobile Device

[mygmctruck1]

Mines currently in paint , bring it home . Reassemble everything , finish all interior trim , install interior door parts , windshield glass , rear window glass and exhaust . get road ready for a week long road rally with 70 other classic vehicles to upper N.Y this May

[DA71Grande]

I think this year I’ll finally get the rear brakes done and maybe new exhaust system, Would like to do fuel injection but I probably would have to find somewhere else to live after the wife found out

[mygmctruck1]

Originally Posted by mygmctruck1

Mines currently in paint , bring it home . Reassemble everything , finish all interior trim , install interior door parts , windshield glass , rear window glass and exhaust . get road ready for a week long road rally with 70 other classic vehicles to upper N.Y this May

Forgot the pic.

[HIGHWAY BY THE SEA]

For my 67 GMC 3500 1 ton, I have the following goals:

1.) Get the front end completely reassembled with the rust-free and dent-free 67 fenders I found this past year.

2.) Get the mint-condition 67 hood installed.

3.) Get the heater system fully operational.

4.) Get the engine to stop running rich (carb maybe).

5.) Fix the horn

6.) Fix the last few small electrical issues

7.) Drive that sucker several times a week!

[1972RedNeck]

Subtract 2 cylinders and triple the horsepower...