The 1947 - Present Chevrolet & GMC Truck Message Board Network







Register or Log In To remove these advertisements.

Go Back   The 1947 - Present Chevrolet & GMC Truck Message Board Network > 47 - Current classic GM Trucks > The 1967 - 1972 Chevrolet & GMC Pickups Message Board

Web 67-72chevytrucks.com


Reply
 
Thread Tools Display Modes
Old 04-14-2020, 07:26 PM   #1
Mts67C10K20
Senior Member
 
Mts67C10K20's Avatar
 
Join Date: May 2017
Location: Dowagiac Michigan
Posts: 202
Stearing column gasket best how to???

So I'm in the home stretch reassembling my 67K20
And before I destroy a new seal is there a better way to install
Besides just stretching it over the shift lever
Thanks all
Attached Images
 
Mts67C10K20 is offline   Reply With Quote
Old 04-14-2020, 08:31 PM   #2
toolboxchev
Registered User
 
Join Date: Jul 2015
Location: 2nd left past the stump on a dirt road.
Posts: 2,629
Re: Stearing column gasket best how to???

So there is a boot that goes over that spring or is it just a small seal I cannot see in the pic immediately?

I initially am thinking soak it in silicon spray.
toolboxchev is offline   Reply With Quote
Old 04-14-2020, 11:17 PM   #3
FirstOwner69
Senior Member
 
FirstOwner69's Avatar
 
Join Date: May 2010
Location: Wisconsin & Arizona
Posts: 4,852
Re: Stearing column gasket best how to???

If you don't consider slitting it destroying it, you could do as shown in this link to a post in a tilt column FAQ.
http://67-72chevytrucks.com/vboard/s...04&postcount=9
__________________
Jim
FirstOwner69 is offline   Reply With Quote
Old 04-15-2020, 10:21 AM   #4
Mts67C10K20
Senior Member
 
Mts67C10K20's Avatar
 
Join Date: May 2017
Location: Dowagiac Michigan
Posts: 202
Re: Stearing column gasket best how to???

Exactly the info I was looking for
Don't mind doing what's necessary on purpose
Just dont like random oops
Thanks
Mts67C10K20 is offline   Reply With Quote
Old 04-15-2020, 11:58 AM   #5
clay68c10
Senior Member
 
clay68c10's Avatar
 
Join Date: Aug 2004
Location: Centennial, CO
Posts: 2,990
Re: Stearing column gasket best how to???

If it’s new you should be able to stretch it. I’ve stretched a few of the GMC Paul’s gaskets successfully.
__________________
ClusterTruck: 68 C10 Bought in 89, wrecked in 03. Slow low $ rebuild started '17. 6.0 & TKO
http://67-72chevytrucks.com/vboard/s...d.php?t=788602
93 K1500 Short Step, 350, NV4500, EBL flash ECU. Vortec heads & roller cam someday...
05 Jeep Wrangler Unlimited. 3” lift & 6-speed
02 E320 the insurance total “free car”
13 Tahoe LTZ
clay68c10 is offline   Reply With Quote
Old 04-15-2020, 05:48 PM   #6
randy500
Account Suspended
 
Join Date: Jul 2016
Location: Tacoma, WA
Posts: 6,873
Re: Stearing column gasket best how to???

Those non tilt columns are super easy to work on and dont need any special tools.
Replace it from the top.
Remove the shift lever
Remove the 3 turn signal screws
Remove the tune aignal cover
Remove the ahift bowl
Remove and replace the grommets

Shift bowl probably needs cleaned and lubed anyway.
randy500 is offline   Reply With Quote
Old 04-15-2020, 06:44 PM   #7
Mts67C10K20
Senior Member
 
Mts67C10K20's Avatar
 
Join Date: May 2017
Location: Dowagiac Michigan
Posts: 202
Re: Stearing column gasket best how to???

Thanks all
Will be installing soon
Mts67C10K20 is offline   Reply With Quote
Old 04-17-2020, 12:09 PM   #8
lousyflyer
Senior Member
 
Join Date: Oct 2013
Location: Garden City, GA
Posts: 296
Re: Stearing column gasket best how to???

Soak it in hot tap water for a few minutes. It will soften the rubber a little.
lousyflyer is offline   Reply With Quote
Old 04-18-2020, 08:52 AM   #9
Mts67C10K20
Senior Member
 
Mts67C10K20's Avatar
 
Join Date: May 2017
Location: Dowagiac Michigan
Posts: 202
Re: Stearing column gasket best how to???

Thanks all for your input and expertise
I tried the stretch method before doing the hub disassembly
Which works well with a new flexible seal and a shoehorn
Attached Images
 
Mts67C10K20 is offline   Reply With Quote
Reply

Bookmarks

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -4. The time now is 10:32 PM.


Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2024, vBulletin Solutions Inc.
Copyright 1997-2022 67-72chevytrucks.com