|
|
|
11-29-2020, 05:37 PM
|
#1 |
|
Registered User
Join Date: Nov 2012
Location: canby,oregon
Posts: 356
|
What to salvage?
I picked up this rig and I have no title,I'm going to salvage what I think is important and the rest is scrap. I know to pick the obvious parts but how far does one go?I already have too much . has a great window frame and firewall and the frame looks good,the beds been cut for parts and the mid section is gone.
|
|
|
|
11-30-2020, 01:44 PM
|
#2 |
|
Senior Member
Join Date: Jan 2005
Location: Raleigh, NC
Posts: 894
|
Re: What to salvage?
If that is an original fuel tank under there it could be worth something. Not sure if anything has changed in recent years but the original tanks were larger than the repops by about four gallons.
The front knuckles, disc brake backing plates, and outer stub shafts are specific to 71-72.
__________________
-Chris Building a stripper, one part at a time: 1969 K5, 307, 3spd, 3 seats, hard top. Added Pwr Discs, Pwr Steering, Aux Battery, T-case Skid, Lighted Sidemarkers, HEI, Lock-Right Diff, ECE Class IV Hitch, 32" MT/Rs. Parts to Install: Hand Throttle, Console, Tow Hooks, Dual Horns, AM-FM, Dealer Swing-Away Tire Carrier, Gas Tank Skid. Also building a 1950 Willys CJ-3A and off-roading a 2001 Nissan Frontier on 1-Ton Portals... |
|
|
|
|
11-30-2020, 03:52 PM
|
#3 |
|
Registered User
Join Date: Dec 2019
Location: Stevensville Md.
Posts: 116
|
Re: What to salvage?
Dash looks uncut
|
|
|
|
|
12-01-2020, 08:54 AM
|
#4 |
|
Registered User
Join Date: Jan 2011
Location: Delaware and Long Island, New York
Posts: 3,456
|
Re: What to salvage?
Some guys out there have enough time and talent, and of course money, where they would put in front and rear floor pans ect, to where they would actually have a K5 again, better than being recycled overseas, guess it depends how hungry one is,
|
|
|
|
|
12-02-2020, 09:59 AM
|
#5 |
|
Senior Member
 Join Date: May 2011
Location: Greencastle PA
Posts: 6,799
|
Re: What to salvage?
Bucket seat bracket under the floor
Gas tank filler hole - truck guys use it to relocate tank Rear taillight sections Sell floor patches If single wall top, cage nuts under top lip I don't scrap much but sometimes I have to hold onto it for a while before it sells, lol |
|
|
|
|
12-02-2020, 10:44 AM
|
#6 |
|
Registered User
Join Date: Jan 2007
Location: Columbus, Ohio
Posts: 4,348
|
Re: What to salvage?
I would save the 72 only rear sheet metal at the end of the bed (where it is notched for the frame) - somebody may need that part for their build.
Good call on the single wall top cage nuts in the top of the besides |
|
|
|
|
12-03-2020, 08:20 PM
|
#7 |
|
Registered User
Join Date: Nov 2012
Location: canby,oregon
Posts: 356
|
Re: What to salvage?
Thanks folks,exactly what I'm looking for, any more ideas list away. I know its a shame to scrap what could be saved but this one has alot going against it and Im no spring chicken anymore.
|
|
|
|
 |
| Bookmarks |
| Thread Tools | |
| Display Modes | |
|
|
Hybrid Mode
