WTT: 1 ton dually - The 1947 - Present Chevrolet & GMC Truck Message Board Network

GloryHound · 02-13-2004, 07:59 PM

What I have
I have a 72 GMC 1 ton dually with flat bed. The truck ran when I parked it. Has headers and dual glass packs on it. The front clip looks OK but the cab is rough, PO pop rivited sheetmetal to the floor to cover up holes. It has a flat bed on it and is a 157" wheelbase truck. The tranny is a 4 speed with granny. The engine is a 305 (not origional). I was going to use this to get parts while I worked on my other truck but due to lack of time I can't go out parts shopping at the junk yards as much as I would like and normally my work schedule won't let me make the swap meets. The title is currently in my brothers name but I can get it swapped not a problem. I also have a 350 engine that can go with it. It looks like it blew a ring and I do not know if it is rebuildable or not. It's only a two bolt main and it was the engine the PO had previously had in it when I bought it. It ran but had a really deep rumble to it.

What I want:
What I am looking for is a rolling short wheel base frame in good shape with a good cab on it. I need the drive shaft also. Prefer trailing arm rear suspension with good trailing arms and rear end. Disc brakes on the front would be nice but not necessary. A bed in any condition is needed for a pattern for putting together a brand new bed and ordering the correct parts.

Must be able to haul the frame to my house and pickup truck from same location. Located near pittsburgh, PA 11 miles off turnpike. Used to be exit 6 but I think it is now 67 since they relabled the exits according to mile markers.

BigBlockBurris · 02-14-2004, 10:45 AM

Pm'd ya!

BBB

GloryHound · 02-14-2004, 11:26 AM

Pic #1

GloryHound · 02-14-2004, 11:28 AM

Pic #2

GloryHound · 02-14-2004, 05:49 PM

pic #3

GloryHound · 02-19-2004, 05:06 PM

Additional Info: Has power brakes and power steering. Since it is a 72 it has front disc brakes.

02-14-2004, 11:28 AM	#4
GloryHound Working on a Nova. Join Date: Nov 2002 Location: ## Posts: 506	Pic #2 Attached Images

02-14-2004, 05:49 PM	#5
GloryHound Working on a Nova. Join Date: Nov 2002 Location: ## Posts: 506	pic #3 Attached Images

Thread Tools
Show Printable Version Email this Page
Display Modes
Switch to Linear Mode Hybrid Mode Switch to Threaded Mode

02-13-2004, 07:59 PM	#1
GloryHound Working on a Nova. Join Date: Nov 2002 Location: ## Posts: 506	WTT: 1 ton dually What I have I have a 72 GMC 1 ton dually with flat bed. The truck ran when I parked it. Has headers and dual glass packs on it. The front clip looks OK but the cab is rough, PO pop rivited sheetmetal to the floor to cover up holes. It has a flat bed on it and is a 157" wheelbase truck. The tranny is a 4 speed with granny. The engine is a 305 (not origional). I was going to use this to get parts while I worked on my other truck but due to lack of time I can't go out parts shopping at the junk yards as much as I would like and normally my work schedule won't let me make the swap meets. The title is currently in my brothers name but I can get it swapped not a problem. I also have a 350 engine that can go with it. It looks like it blew a ring and I do not know if it is rebuildable or not. It's only a two bolt main and it was the engine the PO had previously had in it when I bought it. It ran but had a really deep rumble to it. What I want: What I am looking for is a rolling short wheel base frame in good shape with a good cab on it. I need the drive shaft also. Prefer trailing arm rear suspension with good trailing arms and rear end. Disc brakes on the front would be nice but not necessary. A bed in any condition is needed for a pattern for putting together a brand new bed and ordering the correct parts. Must be able to haul the frame to my house and pickup truck from same location. Located near pittsburgh, PA 11 miles off turnpike. Used to be exit 6 but I think it is now 67 since they relabled the exits according to mile markers. Last edited by GloryHound; 02-14-2004 at 10:05 AM.

02-14-2004, 10:45 AM	#2
BigBlockBurris Registered User Join Date: Nov 2001 Location: Concord,NC,USA Posts: 743	You have a PM Pm'd ya! BBB

02-14-2004, 11:26 AM	#3
GloryHound Working on a Nova. Join Date: Nov 2002 Location: ## Posts: 506	Pic #1 Attached Images

02-19-2004, 05:06 PM	#6
GloryHound Working on a Nova. Join Date: Nov 2002 Location: ## Posts: 506	Additional Info: Has power brakes and power steering. Since it is a 72 it has front disc brakes.



Register or Log In To remove these advertisements.

Register or Log In To remove these advertisements.