Hedman Hedder question - The 1947 - Present Chevrolet & GMC Truck Message Board Network

*wolfthing2000* · 11-14-2004, 12:19 PM

I have a catalog showing Hedman's charts and notes for the correct headers for a small block in a K-20 with a small block.
My concern is a mention in a note of a Dealer installed clutch pivot tube that is " behind or under the rear exhaust tube" .
Does anyone know about what they mean here.???
My 69 looks to be in the same position on frame rail to block as a 66 I had with 327 factory, if someone could snap a picture of there truck linkage at the header area I would be able to compare. I believe I have a stock set up but the location that Hedman talks about is so close to what I have that I am not sure which is which that they talk about????

Thanks,

Dave

jakeslim · 11-14-2004, 12:43 PM

I installed hedman headers last month. The clutch(zbar) to block conection was pretty close to headers, but okay. When clutch is pressed, it does come close to hitting the headers, but just touches (if that). By the way, this is on a 69 k5 4x4. I'll get a pic later(hour or two) if no one else post.

jakeslim

70short · 11-14-2004, 03:40 PM

I have Headman Shorty's. Its close but it fit's fine. I called Headman and talked to them before I purchased from SUMMIT. They have great costumer support. I will be getting rid of the 4-speed and going Auto soon I can't wait. I picked up my headers for approx $135. shipped The local NAPA said he couldn't get them his cost for less than $150.

*wolfthing2000* · 11-14-2004, 09:41 PM

Jakeslim, Do you remember the number for the Hedmans that youhave????
Dave

*wolfthing2000* · 11-15-2004, 01:49 AM

I guess I might call Hedman before ordering.
Dave

11-14-2004, 12:19 PM	#1
wolfthing2000 Account Suspended Join Date: Oct 2004 Posts: 1,276	Hedman Hedder question I have a catalog showing Hedman's charts and notes for the correct headers for a small block in a K-20 with a small block. My concern is a mention in a note of a Dealer installed clutch pivot tube that is " behind or under the rear exhaust tube" . Does anyone know about what they mean here.??? My 69 looks to be in the same position on frame rail to block as a 66 I had with 327 factory, if someone could snap a picture of there truck linkage at the header area I would be able to compare. I believe I have a stock set up but the location that Hedman talks about is so close to what I have that I am not sure which is which that they talk about???? Thanks, Dave

11-14-2004, 03:40 PM	#3
70short Registered User Join Date: Sep 2003 Location: Boise ID Posts: 609	Headman I have Headman Shorty's. Its close but it fit's fine. I called Headman and talked to them before I purchased from SUMMIT. They have great costumer support. I will be getting rid of the 4-speed and going Auto soon I can't wait. I picked up my headers for approx $135. shipped The local NAPA said he couldn't get them his cost for less than $150. __________________ "72" Red CORVETTE 4-speed 350 "70" Chevy Short Bed early stages of resto. Edel 600 cfm carb Weiand Stealth Intake HEI shorty Headers 4/2 Drop 295 50R 15 TOYO on 10 inch wide corvette rally rims at all 4 corners. "CHEVY RULES"

11-14-2004, 12:43 PM	#2
jakeslim Premium Level Member Join Date: Aug 2004 Location: Northern CA Posts: 829	I installed hedman headers last month. The clutch(zbar) to block conection was pretty close to headers, but okay. When clutch is pressed, it does come close to hitting the headers, but just touches (if that). By the way, this is on a 69 k5 4x4. I'll get a pic later(hour or two) if no one else post. jakeslim

11-14-2004, 09:41 PM	#4
wolfthing2000 Account Suspended Join Date: Oct 2004 Posts: 1,276	Jakeslim, Do you remember the number for the Hedmans that youhave???? Dave

11-15-2004, 01:49 AM	#5
wolfthing2000 Account Suspended Join Date: Oct 2004 Posts: 1,276	I guess I might call Hedman before ordering. Dave



Register or Log In To remove these advertisements.

Register or Log In To remove these advertisements.