The 1947 - Present Chevrolet & GMC Truck Message Board Network







Register or Log In To remove these advertisements.

Go Back   The 1947 - Present Chevrolet & GMC Truck Message Board Network > 47 - Current classic GM Trucks > The 1973 - 1987 Chevrolet & GMC Squarebody Pickups Message Board

Web 67-72chevytrucks.com


Reply
 
Thread Tools Display Modes
Old 02-09-2014, 10:56 PM   #1
Theoriginalsilverado
Registered User
 
Join Date: Nov 2013
Location: Norris Arm NL
Posts: 126
Exclamation Quick question please help

Hey Guys. I have my square stripped down to the chassis. Yesterday I began to sand. I had an area about 3 feet long stripped down to bare metal on just the top of the drivers side of the chassis. Unfortunately an emergency happened at work and I had to take off before I had a chance to roll the chassis back in the garage.

Living in Canada and it being Winter, by the time I got back the area was well rusted. Rust is nothing new for the truck, it's covered, but this is rust that is directly on bare metal, which is unprotected from any type of paint or primer from the factory.

My question is will this hurt the chassis? If so what can I do to counteract any damages? And when I sand again will resanding this area take off too much metal?

Remember it's bare metal that rusted, it was not covered by any paint or primer.

Thanks
__________________
If It runs like a Chevy, it probably is!
Theoriginalsilverado is offline   Reply With Quote
Old 02-09-2014, 11:08 PM   #2
79Betty
Registered User
 
79Betty's Avatar
 
Join Date: Jan 2013
Location: Jasper, IN
Posts: 948
Re: Quick question please help

I had that with my 96 ranger. I just sanded it again n couldn't tell.
__________________
When in doubt, throttle it out!
1974 Chevrolet Custom K20
2005 Ford Ranger Edge
1985 Chevrolet Custom Deluxe C10
79Betty is offline   Reply With Quote
Old 02-09-2014, 11:31 PM   #3
bnoon
Registered User
 
Join Date: Jul 2012
Location: Des Moines IA
Posts: 1,250
Re: Quick question please help

Anything I've done that I can't paint or primer right away, I've used Eastwood's Fast Etch (used to have a different name, but this is their improved stuff). http://www.eastwood.com/eastwood-s-fast-etch.html It leaves a zinc phosphate coating that won't rust. All you have to do is spray it on when you're done grinding/sanding. When it comes time to paint, you just prep like normal (thinner, pre-paint prep recommended by your paint manufacturer, etc).
__________________
- 1981 Sierra 454, NV4500 swap
- 2006 Z06, 25k miles
- 1973 Nova - Project CarNova Virus on Youtube
bnoon is offline   Reply With Quote
Old 02-09-2014, 11:33 PM   #4
bnoon
Registered User
 
Join Date: Jul 2012
Location: Des Moines IA
Posts: 1,250
Re: Quick question please help

BTW, the Fast Etch would save you from having to resand what you've already done, in addition to putting off having to hurry to get to the painting stage.
__________________
- 1981 Sierra 454, NV4500 swap
- 2006 Z06, 25k miles
- 1973 Nova - Project CarNova Virus on Youtube
bnoon is offline   Reply With Quote
Reply

Bookmarks

Tags
rust, sanding


Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -4. The time now is 10:09 AM.


Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2024, vBulletin Solutions Inc.
Copyright 1997-2022 67-72chevytrucks.com