![]() |
|
![]() |
#1 |
Registered User
Join Date: Aug 2020
Location: Braunschweig, Lower Saxony, Germany
Posts: 782
|
A '62 has to get back on the road
Hello, I bought this '62 C10 with 350/350,
it has power steering and power brake. Unfortunately, the sheet metal is in very poor condition and needs attention. I've been reading this great forum for a long time and I want to take this opportunity to thank everyone who helped me with their reports. I'll start: There it is my new truck, the usual disassembly and all for sandblasting Last edited by Braunschweiger; 01-14-2022 at 11:48 AM. |
![]() |
![]() |
![]() |
#2 |
Registered User
Join Date: Aug 2020
Location: Braunschweig, Lower Saxony, Germany
Posts: 782
|
Re: A '62 has to get back on the road
After sandblasting, all the holes showed up.
|
![]() |
![]() |
![]() |
#3 |
Registered User
Join Date: Aug 2020
Location: Braunschweig, Lower Saxony, Germany
Posts: 782
|
Re: A '62 has to get back on the road
Let's move on, the corner of the roof
is the beginning. And it was made out of 4 parts. Roof, Gutterwall and Gutterfloor. I hope the technical terms are correct. The front edge of the roof also had to give way. |
![]() |
![]() |
![]() |
#4 |
Registered User
Join Date: Aug 2020
Location: Braunschweig, Lower Saxony, Germany
Posts: 782
|
Re: A '62 has to get back on the road
New sheet metal must be installed inside and outside above
the windscreen and on the passenger side above the door. Recreating the inner post corner was very complicated, I don't want to do it again |
![]() |
![]() |
![]() |
#5 |
Registered User
Join Date: Aug 2020
Location: Braunschweig, Lower Saxony, Germany
Posts: 782
|
Re: A '62 has to get back on the road
The outer panel fitted, unfortunately it is
almost 1/2" too short, so adjust it. A little Bondo is necessary. That looks better. |
![]() |
![]() |
![]() |
#6 |
Moderator
![]() ![]() Join Date: Aug 2011
Location: China Spring, TX
Posts: 7,280
|
Re: A '62 has to get back on the road
Wow, your definitely putting your time in on that unit.
![]()
__________________
Master Chief, US Navy, Retired 1964 C10 Step-side Short Bed - In Progress 2009 2500HD Duramax LTZ 1948 GMC Panel 1956 Big Window Stepside 1953 5 Window Chevy Stepside 1932 Coupe New Seat Foam for Bench Seats? |
![]() |
![]() |
![]() |
#7 |
Registered User
Join Date: Aug 2020
Location: Braunschweig, Lower Saxony, Germany
Posts: 782
|
Re: A '62 has to get back on the road
I've been retired for a while.
I didn't want to just look out the window and am now rebuilding this beautiful piece of American history. Last edited by Braunschweiger; 01-14-2022 at 02:16 PM. |
![]() |
![]() |
![]() |
#8 |
Senior Member
![]() ![]() ![]() Join Date: Jan 2018
Location: Hickory Flat, GA
Posts: 4,468
|
Re: A '62 has to get back on the road
I like the stance before you tore it down. Will you be keeping it that way?
Great job on the repairs too. That rust was extensive
__________________
Christian Carpenter 1963 C10 - Frankentruck 283, Muncie 3 speed with overdrive Overdrive wiring here1963-ish truck bed trailer - Half-Wit 1981 C10 - Penny 305, th350 --> Soon to be 350, Saginaw 4 speed 1995 Dodge Dakota Sport "I'll put it simple: if you're going hard enough left, you'll find yourself turning right." - Doc Hudson |
![]() |
![]() |
![]() |
#9 |
Registered User
Join Date: Aug 2020
Location: Braunschweig, Lower Saxony, Germany
Posts: 782
|
Re: A '62 has to get back on the road
Yes, the truck gets a 63 front axle with 2.5" drop spindles
and 2" dropped springs, the torsion keys have already hit hard. Closed a hole on the right side of the post, opened the airvents to close the holes |
![]() |
![]() |
![]() |
#10 |
Registered User
Join Date: Aug 2020
Location: Braunschweig, Lower Saxony, Germany
Posts: 782
|
Re: A '62 has to get back on the road
Airvent closed again, that was necessary
on both sides. |
![]() |
![]() |
![]() |
#11 |
Registered User
Join Date: Aug 2020
Location: Braunschweig, Lower Saxony, Germany
Posts: 782
|
Re: A '62 has to get back on the road
The floor has to be completely renewed,
first build a support and cut out the rusty part, not much is left. |
![]() |
![]() |
![]() |
#12 |
Registered User
Join Date: Aug 2020
Location: Braunschweig, Lower Saxony, Germany
Posts: 782
|
Re: A '62 has to get back on the road
On the other Side, same Play
|
![]() |
![]() |
![]() |
#13 |
Registered User
Join Date: Apr 2012
Location: Beaver, Pa.
Posts: 197
|
Re: A '62 has to get back on the road
Following along, love the stance of your truck. I always enjoy watching sheet metal work done well.
|
![]() |
![]() |
![]() |
#14 |
Registered User
Join Date: Aug 2020
Location: Braunschweig, Lower Saxony, Germany
Posts: 782
|
Re: A '62 has to get back on the road
Thank you, I'll do my best.
|
![]() |
![]() |
![]() |
#15 |
Registered User
Join Date: Aug 2020
Location: Braunschweig, Lower Saxony, Germany
Posts: 782
|
Re: A '62 has to get back on the road
The frame above the driver's door also had to be replaced,
as did the corner of the roof, and patches were also put in on the rear window. Reinforcements for the belts have been placed |
![]() |
![]() |
![]() |
#16 |
Registered User
Join Date: Aug 2020
Location: Braunschweig, Lower Saxony, Germany
Posts: 782
|
Re: A '62 has to get back on the road
Grind the welds on the floor and make a deflector plate
for the DeLuxe heater. Eliminate dents on the back wall. |
![]() |
![]() |
![]() |
#17 |
Registered User
Join Date: Aug 2020
Location: Braunschweig, Lower Saxony, Germany
Posts: 782
|
Re: A '62 has to get back on the road
The holder closed with a patch, more belt reinforcements set,
the cabin is patched, now we continue with the doors |
![]() |
![]() |
![]() |
#18 |
Registered User
Join Date: Dec 2012
Location: Rochester, KENT
Posts: 10,529
|
Re: A '62 has to get back on the road
That is an awesome job you are doing.
Very brave in places. Well done.
__________________
MY BUILD LINK: http://67-72chevytrucks.com/vboard/s...585901]Redneck Express - 1966 C10 Short Fleetside MY USA ROADTRIPS http://forum.retro-rides.org/thread/...2018-humdinger IF YOU CAN'T FIX IT WITH A HAMMER, YOU'VE GOT AN ELECTRICAL PROBLEM MATE. |
![]() |
![]() |
![]() |
#19 |
One foot in front of the other
![]() Join Date: Aug 2008
Location: Parrottsville, TN
Posts: 5,440
|
Re: A '62 has to get back on the road
Very nice work.
|
![]() |
![]() |
![]() |
#20 |
Registered User
Join Date: Aug 2020
Location: Braunschweig, Lower Saxony, Germany
Posts: 782
|
Re: A '62 has to get back on the road
The door fits well, the gaps look good,
I adjusted the gaps that were too wide by welding. Then the passenger side started. |
![]() |
![]() |
![]() |
#21 |
Registered User
Join Date: Aug 2020
Location: Braunschweig, Lower Saxony, Germany
Posts: 782
|
Re: A '62 has to get back on the road
Adjust rear mirror holes again.
Check the gaps again, then spot weld step by step again, which weld to wide gaps. |
![]() |
![]() |
![]() |
#22 |
Registered User
Join Date: Aug 2020
Location: Braunschweig, Lower Saxony, Germany
Posts: 782
|
Re: A '62 has to get back on the road
Now the finishing work, grinding off the long weld seam
and eliminating the dents from welding as far as possible, then smoothing with Bondo. Assemble everything for testing and be happy that it worked well. |
![]() |
![]() |
![]() |
#23 |
Registered User
Join Date: Aug 2020
Location: Braunschweig, Lower Saxony, Germany
Posts: 782
|
Re: A '62 has to get back on the road
The two fenders got patches and the holes in the decorative strip welded shut were fixed, there were quite a few. Fixed a patch and the reinforcement plate in front.
|
![]() |
![]() |
![]() |
#24 |
Registered User
Join Date: Dec 2012
Location: Rochester, KENT
Posts: 10,529
|
Re: A '62 has to get back on the road
Your progress is amazing Harald.
Is that a Jeep Wagoneer in the shop ?
__________________
MY BUILD LINK: http://67-72chevytrucks.com/vboard/s...585901]Redneck Express - 1966 C10 Short Fleetside MY USA ROADTRIPS http://forum.retro-rides.org/thread/...2018-humdinger IF YOU CAN'T FIX IT WITH A HAMMER, YOU'VE GOT AN ELECTRICAL PROBLEM MATE. |
![]() |
![]() |
![]() |
#25 |
Registered User
Join Date: Sep 2002
Location: Liberty, Mississippi
Posts: 671
|
Re: A '62 has to get back on the road
gute Arbeit
|
![]() |
![]() |
![]() |
Bookmarks |
|
|