![]() |
|
![]() |
#1 |
Registered User
Join Date: Jun 2002
Location: Fort Worth, TX
Posts: 920
|
Stubborn ball joint
Redoing front-end and am in the final stretch. My problem is the passenger side lower ball joint just will not break free. Went to harbor freight this morning and got a bigger sledge. Just thought I would ask is there anything else I could try? Thanks guys.
|
![]() |
![]() |
![]() |
#2 |
Registered User
Join Date: Oct 2016
Location: Dallas Texas
Posts: 3,090
|
Re: Stubborn ball joint
.
Go borrow the tool from Autozone and press it out. You'll need that same tool to press the new one back in! Hth, -klb
__________________
67 C10 fleet fuel injected '70 402, 700r4, 3.73 posi 07 335 sport turbo 6sp 94 Trans Am GT LT1 6sp posi -- sold after 22yrs 99 540 sport V8 6sp -- sold 73 240z L24 4sp -- given to friend 68 C10 step 350/350 3.73 open -- sold |
![]() |
![]() |
![]() |
#3 |
Registered User
Join Date: Jan 2007
Location: Puyallup, WA
Posts: 1,662
|
Re: Stubborn ball joint
Yes, this. And the ball joint press is easy to use.
__________________
72 C10 lwb fleetside -stock 350/350 combo |
![]() |
![]() |
![]() |
#4 |
Moderator
![]() Join Date: Jun 2017
Location: Cherryville, NC
Posts: 2,193
|
Re: Stubborn ball joint
If you have the suspension arm hanging free, it is most likely moving back and forward with the hammer blows...
Put a floor jack under the ball joint and take a little weight up on the jack.... I use a pickle fork and 5 LB hammer...so long as I am not reusing the ball joint... Hope this helps.. ![]() ![]() ![]()
__________________
Family and country before all others... 2006 Chevy Silverado (Daily Driver) 2012 Chevy Equinox ![]() ![]() ![]() |
![]() |
![]() |
![]() |
#5 |
Registered User
Join Date: Jun 2002
Location: Fort Worth, TX
Posts: 920
|
Re: Stubborn ball joint
Thanks. I should have made it clear I am replacing control arm and all.. Problem is brealing old one free from the spindle... It just doesn't seem to move
|
![]() |
![]() |
![]() |
#6 |
Registered User
Join Date: Oct 2016
Location: Dallas Texas
Posts: 3,090
|
Re: Stubborn ball joint
.
Use the hammer against the knuckle swinging perpendicular to the ball joint shaft. Give it a good hit and the thing should just slide right loose. Careful of the spring though. Either that or use a pickle fork to separate the two pieces. Hth, -klb
__________________
67 C10 fleet fuel injected '70 402, 700r4, 3.73 posi 07 335 sport turbo 6sp 94 Trans Am GT LT1 6sp posi -- sold after 22yrs 99 540 sport V8 6sp -- sold 73 240z L24 4sp -- given to friend 68 C10 step 350/350 3.73 open -- sold |
![]() |
![]() |
![]() |
#7 |
Registered User
Join Date: Jun 2002
Location: Fort Worth, TX
Posts: 920
|
Re: Stubborn ball joint
The knuckle on the spindle?
|
![]() |
![]() |
![]() |
#8 |
Registered User
Join Date: Oct 2016
Location: Dallas Texas
Posts: 3,090
|
Re: Stubborn ball joint
.
Sorry, the thick metal boss that the ball joint shaft is stuck in. Hit that perpendicular to the ball joint shaft. Hit it hard. -klb
__________________
67 C10 fleet fuel injected '70 402, 700r4, 3.73 posi 07 335 sport turbo 6sp 94 Trans Am GT LT1 6sp posi -- sold after 22yrs 99 540 sport V8 6sp -- sold 73 240z L24 4sp -- given to friend 68 C10 step 350/350 3.73 open -- sold |
![]() |
![]() |
![]() |
#9 |
Moderator
![]() Join Date: Jun 2017
Location: Cherryville, NC
Posts: 2,193
|
Re: Stubborn ball joint
Yep...thats what I assumed you were attempting....
Be safe though....make sure the lower A arm is on a floor jack....to take the weight of the spring load etc... I assume you have the shock absorber off of it already.... Sometimes its necessary to have a solid hammer against the back on the balljoint hole on the spindle then hit the other side of the spindle....to shock it out.... ![]() ![]() ![]()
__________________
Family and country before all others... 2006 Chevy Silverado (Daily Driver) 2012 Chevy Equinox ![]() ![]() ![]() |
![]() |
![]() |
![]() |
#10 |
Registered User
Join Date: Jun 2002
Location: Fort Worth, TX
Posts: 920
|
Re: Stubborn ball joint
Thanks I will try that. Never had this happen before☺
|
![]() |
![]() |
![]() |
#11 |
Registered User
Join Date: May 2014
Location: San Diego, CA
Posts: 547
|
Re: Stubborn ball joint
I just re-did all the front end components on my truck.
It took a big hammer and lots blows to get the ball joint free from the spindles....but eventually they broke free.
__________________
Project Engine Stand 1972 SWB conversion: http://67-72chevytrucks.com/vboard/s...d.php?t=673914 1970 Nova: http://67-72chevytrucks.com/vboard/s...d.php?t=708161 |
![]() |
![]() |
![]() |
#12 |
Registered User
Join Date: Jan 2007
Location: Puyallup, WA
Posts: 1,662
|
Re: Stubborn ball joint
You may have to use 2 pickle forks as well.
__________________
72 C10 lwb fleetside -stock 350/350 combo |
![]() |
![]() |
![]() |
#13 |
Registered User
Join Date: Jun 2002
Location: Fort Worth, TX
Posts: 920
|
Re: Stubborn ball joint
2 forks? What stack them?
|
![]() |
![]() |
![]() |
#14 |
Registered User
Join Date: Jun 2002
Location: Fort Worth, TX
Posts: 920
|
Re: Stubborn ball joint
Never mind realized what you mean lol
|
![]() |
![]() |
![]() |
#15 |
Registered User
Join Date: Jan 2007
Location: Puyallup, WA
Posts: 1,662
|
Re: Stubborn ball joint
Yes, you'll have to stack them. I've had to do that before when things were being a pain.
__________________
72 C10 lwb fleetside -stock 350/350 combo |
![]() |
![]() |
![]() |
#16 |
Senior Member
![]() Join Date: Dec 2009
Location: TN.
Posts: 8,102
|
Re: Stubborn ball joint
If you like buying tools like I do.
Video with air hammer and pickle fork. https://www.youtube.com/watch?v=fxhfSBGs2ls Tool kit for air hammer or you can just use a hammer. https://www.amazon.com/HFS-Piece-Joi...productDetails .
__________________
________________________________________________________________________________________ ____________________________________________ 84 Chevy K-20 63 Impala (my high school car) http://67-72chevytrucks.com/vboard/s...Crew Cab Build |
![]() |
![]() |
![]() |
#17 |
Post Whore
![]() Join Date: Feb 2016
Location: Portland Oregon
Posts: 11,137
|
Re: Stubborn ball joint
If things are particularly stubborn apply some soft heat with a Propane or Mapp gas torch to the spindle. Cleaning all grease and removing the brake hose for fire safety are required! Having the Pickle Fork in position and preloaded will help. The idea being to heat the spindle and get the ball joint loose before the heat from the spindle is conducted to the ball joint. A hundred degrees difference between the two pieces will give you a thousands or two of clearance.
__________________
Thanks to Bob and Jeanie and everyone else at Superior Performance for all their great help. ![]() RIP Bob Parks. 1967 Burban (the WMB),1988 S10 Blazer (the Stink10 II),1969 GTO (the Goat), 1970 Javelin, 1952 F2 Ford OHC six 4X4, 29 Model A, 72 Firebird (the DBP Bird). 85 Alfa Romeo If it breaks I didn't want it in the first place The WMB repair thread http://67-72chevytrucks.com/vboard/s...d.php?t=698377 |
![]() |
![]() |
![]() |
#18 |
Junior Member
![]() Join Date: Jul 2014
Location: Huntsville, AL
Posts: 75
|
Re: Stubborn ball joint
Just did this last year. I had a stubborn one too. I got the pickle fork under it good and tight, then whacked the knuckle with a two pound hammer just above the fork. Popped right loose. Like others have said, be safe. Leave the nut loose on the joint to keep everything together until you're sure you're ready to deal with the spring.
|
![]() |
![]() |
![]() |
#19 |
Senior Member
![]() Join Date: Mar 2003
Location: Colfax-California
Posts: 8,528
|
Re: Stubborn ball joint
Let the arm hang without the floor jack touching it, but still underneath it about an inch or 2. Frame on the jack stand. Loosen the nut about 3-4 turns and leave it on. Hit the side of the spindle. The vibration and the pressure of the spring will jack it free. After it separates, then use the floor jack to raise it up enough to spin the nut the rest of the way. Lower floor jack slowly until the spring pressure is off and the ball joint is free.
|
![]() |
![]() |
![]() |
#20 |
Registered User
Join Date: Jun 2002
Location: Fort Worth, TX
Posts: 920
|
Re: Stubborn ball joint
Thanks for all the advice guys. Did what you said klb about hitting it perpendicular. Then used the fork and my new 8 lbs sledge... Came free after the 2nd hit. Now to get it aligned and put some miles on it. Again thanks to all for the advice.
|
![]() |
![]() |
![]() |
Bookmarks |
|
|