![]() |
|
![]() |
#1 |
Registered User
Join Date: Sep 2018
Location: San Diego, CA
Posts: 15
|
Bell housing question
I have a 1969 C10 that we are switching from Inline 6 to V8. I had a question on the manual tranny bell housing.
Do I need the bell housing with the rear mount pads? I have seen aluminum bell housings that do not have that mounting surface. The tranny is a Saginaw 4 speed out of my friend's 1969 Camaro. Thanks ahead of time for your help! war |
![]() |
![]() |
![]() |
#2 |
Registered User
![]() Join Date: May 2013
Location: Vero Beach FL
Posts: 290
|
Re: Bell housing question
No, the only ones I have seen use those were on my 56 210
|
![]() |
![]() |
![]() |
#3 | |
Registered User
Join Date: May 2019
Location: Lakewood
Posts: 82
|
Re: Bell housing question
Quote:
If you do not already have that crossmember, I would pick up an aluminum bellhousing and install a generic transmission crossmember under the tailhousing of the 4-speed. |
|
![]() |
![]() |
![]() |
#4 |
Registered User
![]() Join Date: May 2013
Location: Vero Beach FL
Posts: 290
|
Re: Bell housing question
I stand corrected.
|
![]() |
![]() |
![]() |
#5 |
Registered User
Join Date: Sep 2018
Location: San Diego, CA
Posts: 15
|
Re: Bell housing question
Thank you for the info. Bone stock truck with crossmember. So I will source a bell housing with the mount.
|
![]() |
![]() |
![]() |
#6 |
Registered User
![]() Join Date: May 2013
Location: Vero Beach FL
Posts: 290
|
Re: Bell housing question
I have a Lakewood on my 56 with the mounts
|
![]() |
![]() |
![]() |
#7 |
The Older Generation
![]() ![]() ![]() Join Date: Aug 2006
Location: Montezuma, Iowa
Posts: 25,492
|
Re: Bell housing question
-
If you are going to use the bell housing trans mounts the cross member for the bell housing mounts are different for the I6 and V8. LockDoc
__________________
Leon Locksmith, Specializing In Antique Trucks, Automobiles, & Motorcycles (My Dually Pickup Project Thread) http://67-72chevytrucks.com/vboard/s...d.php?t=829820 - Last edited by LockDoc; 11-26-2019 at 01:33 AM. |
![]() |
![]() |
![]() |
#8 |
Senior Member
![]() Join Date: Dec 2013
Location: Gods country East,Tn
Posts: 8,545
|
Re: Bell housing question
Here are a few more pictures of the 6 vs 8 manual trans cross member . I did this conversion on my 67 short bed frame to mount the 350 v8 in the correct position .
![]() the V8 cross member is on the left with picture of the V8 engine perches . changing cross members with the cab on the frame is tough . You can drop a small block in using most of the 6 parts and a lot of guys do to avoid all the extra work and a bunch of new parts to do a correct 6 to V8 conversion install .
__________________
![]() 1967 Factory short bed - Old school '71 - 350 / 4bolt / 487 heads / Edelbrock C3BX Muncie M-22 4 speed / Hurst Comp plus Factory 12 bolt posi 3.73 / 255-70-15 Smoothed firewall / Factory cowl induction Power disc brakes / power steering / 3.5-5" drop Last edited by Grumpy old man; 11-26-2019 at 07:35 AM. |
![]() |
![]() |
![]() |
#9 |
Registered User
Join Date: Dec 1999
Location: Austin, TX, USA
Posts: 7,717
|
Re: Bell housing question
If I were swapping an L6 truck to small block I would keep it in the 6 cylinder position. That should give a better weight balance to the truck and also allow for a shorter driveshaft if going one piece.
On top of that it is a lot less work than removing rivets and finding donor parts. As mentioned above, it would appear different than a factory optioned V8 truck.
__________________
44 Willys MB 52 M38A1 64 Corvette Coupe 68 Camaro 'vert LT1 & TH700 69 Z/28 355 12.6's @110 69 Chevy Short Step 4 1/2"/7" drop 72 Jimmy 4WD 4spd 4" & 35's 02 GMC 2500HD 4x4 Duramax |
![]() |
![]() |
![]() |
Bookmarks |
|
|