fresh 350 engine built 4 sale or trade - The 1947 - Present Chevrolet & GMC Truck Message Board Network

jamal · 05-16-2005, 07:38 PM

Hello, I am new to this board, but have somebody a good deal if they want it. I have a 350 with .40 over forged flat tops, 284 duration & .480 lift, roller tip steel rockers, 305 heads with race valves and headwork, new edlebrock torker 2 aluminum intake, bottom end has 1000 miles on it, and the heads, roller tip rockers, and intake have zero miles, never even been started. The reason the engine is so low mileage I built it for my truck and put the fuel injection heads and fuel injection back on it, and the computer did not get along with the cam so I put a stock back in my truck, and put the intake and heads on to put in my 67. I would sell it for $800 or trade even for a good running straight six for my 67 chevy truck. This is my daily driver and I need better gas mileage than this 350 plus I want to keep the 3 on the tree. I am located in bridgeport, al

LUV2XCLR8 · 05-16-2005, 07:56 PM

Wowsers, Hey Bill "palf70step", Here's Your Chance At A V8

cableguy0 · 05-16-2005, 08:55 PM

what cc are those heads? what compression is it?

jamal · 05-16-2005, 09:29 PM

I think they were 58cc but I will have to check with the machine shop, however is supposed to be 10:1 compression. The pistons are stated at 9.15 compression with 64 cc, so if you know how to cross reference the #'s that should tell you exactly what it is. Is supposed to run on pump gas, so shouldn't be much if any higher than 10:1

70rs/ss · 05-16-2005, 10:19 PM

Quote:

Originally Posted by jamal

I think they were 58cc but I will have to check with the machine shop, however is supposed to be 10:1 compression. The pistons are stated at 9.15 compression with 64 cc, so if you know how to cross reference the #'s that should tell you exactly what it is. Is supposed to run on pump gas, so shouldn't be much if any higher than 10:1

Where are you? I might be interested.

Mike

jamal · 05-16-2005, 10:26 PM

I am a good bit away from you, I live in Bridgeport, AL zip 35740. I could crate it if needed and drop off at a shipper of your choice if needed

jamal · 05-16-2005, 11:16 PM

Believe it or not I think I just found a buyer, actually my father in law saw I had it on here and said he may want it. I will let you know if he decides not to.

05-16-2005, 07:38 PM	#1
jamal Registered User Join Date: Apr 2005 Location: Bridgeport, AL Posts: 363	fresh 350 engine built 4 sale or trade Hello, I am new to this board, but have somebody a good deal if they want it. I have a 350 with .40 over forged flat tops, 284 duration & .480 lift, roller tip steel rockers, 305 heads with race valves and headwork, new edlebrock torker 2 aluminum intake, bottom end has 1000 miles on it, and the heads, roller tip rockers, and intake have zero miles, never even been started. The reason the engine is so low mileage I built it for my truck and put the fuel injection heads and fuel injection back on it, and the computer did not get along with the cam so I put a stock back in my truck, and put the intake and heads on to put in my 67. I would sell it for $800 or trade even for a good running straight six for my 67 chevy truck. This is my daily driver and I need better gas mileage than this 350 plus I want to keep the 3 on the tree. I am located in bridgeport, al

05-16-2005, 07:56 PM	#2
LUV2XCLR8 The LuvShack Garage Join Date: Jan 2004 Location: Maple Grove, TN (West Side) Posts: 30,475	Wowsers, Hey Bill "palf70step", Here's Your Chance At A V8 __________________ Owner/Op: "TN Classic Transport Carriers" The Toy: "Square Vette" 72 Hybrid Blazer Toy Barn: "LuvShack" 40 x 60 x 20 Shop Big Piggy: "Goliath" 07 Kodiak C4500 Lil Piggy:"Maddy" 88 Silverado 3500 Hauler: "Feathers" 14 Aluma 8218T

05-16-2005, 08:55 PM	#3
cableguy0 Senior Member Join Date: Apr 2000 Location: Delta,Pa Posts: 14,950	what cc are those heads? what compression is it? __________________ Owner of North Point Car Care in Dundalk Md. We specialize in custom exhaust on both modern and classic vehicles. We are a full service auto shop from classics to modern vehicles. Feel free to contact me with questions. I will give a 10% discount to any board member.

05-16-2005, 09:29 PM	#4
jamal Registered User Join Date: Apr 2005 Location: Bridgeport, AL Posts: 363	I think they were 58cc but I will have to check with the machine shop, however is supposed to be 10:1 compression. The pistons are stated at 9.15 compression with 64 cc, so if you know how to cross reference the #'s that should tell you exactly what it is. Is supposed to run on pump gas, so shouldn't be much if any higher than 10:1

05-16-2005, 10:26 PM	#6
jamal Registered User Join Date: Apr 2005 Location: Bridgeport, AL Posts: 363	I am a good bit away from you, I live in Bridgeport, AL zip 35740. I could crate it if needed and drop off at a shipper of your choice if needed

05-16-2005, 11:16 PM	#7
jamal Registered User Join Date: Apr 2005 Location: Bridgeport, AL Posts: 363	Believe it or not I think I just found a buyer, actually my father in law saw I had it on here and said he may want it. I will let you know if he decides not to.



Register or Log In To remove these advertisements.

Register or Log In To remove these advertisements.