![]() |
Register or Log In To remove these advertisements. |
|
|
![]() |
|
Thread Tools | Display Modes |
|
![]() |
#1 |
Registered User
Join Date: Jul 2007
Location: Fall River California
Posts: 2,026
|
A little trailer/camper mishap dented my bumper
My wife and I went on a last minute camp trip this weekend. In my hurry to get on the road I didn't slide the hitch into the reciever far enough and completely missed the hole with the hitch pin, drove about a block and heard a loud scraping noise behind me, looked in the mirror to see my prized home built teardrop trailer grinding toungue first on the road, I tried to decelerate slow enough to keep it from rear ending my truck, I thought I had it until the safety chain sprang the trailer into my bumper destroying the batter/propane box mounted in front on the toungue. Fortunately the box is separate from the body of the camper and is easily rebuilt but when it hit my brand new chrome bumper it forced the bumper against the mounts and made a bump near the two inner bolts. I hope I can tap them out, they're not very noticeable but they suck!
One concelation to this, also in my hurry I failed to plug in the trailer lights, it was dark when I got on the road and if the trailer hadn't fallen off I would have hit the hi way without lights and could have been hit, possibly hurting not only my wife and I but anyone behind me. I got lucky this time and will be a lot more careful in the future! Anyone know how to tap dents out of a chrome bumper! Posted via Mobile Device
__________________
http://smg.photobucket.com/albums/v655/aaronhero/ |
![]() |
![]() |
![]() |
#2 |
Registered User
Join Date: Oct 2010
Location: everett washington
Posts: 382
|
Re: A little trailer/camper mishap dented my bumper
remove the bumper, lay it chrome side down an a thickly padded hard surface, than take a smooth faced 16-20oz hammer and start tapping the dents out. Remember you can move metal faster and with more control with rapid light inpacts then with hard inpacts. start tapping in a circler motion from the outside to the center of the dent. inspect often to avoid over pushing the damaged areas and chacking the chrome.
by the way - ![]()
__________________
a wise man once said "There are only two real rules to life... 1 - Don't sweat the small stuff 2 - Everything is small stuff |
![]() |
![]() |
![]() |
#3 | |
Registered User
Join Date: Jul 2007
Location: Fall River California
Posts: 2,026
|
Re: A little trailer/camper mishap dented my bumper
Quote:
Posted via Mobile Device
__________________
http://smg.photobucket.com/albums/v655/aaronhero/ |
|
![]() |
![]() |
![]() |
#4 |
I am a Referee of life.
Join Date: Jun 2000
Location: Greensboro N.C.
Posts: 13,993
|
Re: A little trailer/camper mishap dented my bumper
Sorry to hear of the problems with your beautiful truck and trailer.Glad the damage was minor.Hope the bumper comes out well for you.
__________________
The 47-present Chevrolet and GMC Truck Message Board Network,it's owners,moderators,members,and associates of any type should not be held responsible for my opinion. You can't fix stupid,not even with duct tape. "My appearance is due to the fact that "GOD" does punish you for having too much fun!" Barrett-Jackson has perfected alchemy,they make rust into gold! "You can lead a horse to water but you can't saddle a duck" "Cleverly disguised as a 'Responsible Adult' "Sometimes your Knight in shining armor is just a retard in tinfoil" |
![]() |
![]() |
![]() |
#5 |
Registered User
Join Date: May 2010
Location: Edmonton, Alberta
Posts: 3,850
|
Re: A little trailer/camper mishap dented my bumper
These are the kind of things that happen when trucks actually get used! And for that you get extra points
![]()
__________________
--------------------------------------------------------------- Jason. 68’ GMC shortbox https://67-72chevytrucks.com/vboard/...d.php?t=794201 72' 2WD Blazer http://67-72chevytrucks.com/vboard/s...d.php?t=425385 67' LongBox C-10 http://67-72chevytrucks.com/vboard/s...d.php?t=691845 InstaGram ybnorml67 |
![]() |
![]() |
![]() |
#6 |
Registered User
Join Date: Oct 2010
Location: everett washington
Posts: 382
|
Re: A little trailer/camper mishap dented my bumper
do the same thing only put a clean rag on the end of the hammer must be a smooth face or you will damage the plating. you can lightly heat the backside of the bumper to help but be careful to not use too much heat or it will discolor the face. the plastic deadblow will be of no use here. just use a 16-20oz metal hammer with a rag on it and use rapid light impacts it'll be slow going but you won't damage the plating and still fix the damage.
personaly I would leave it alone as it shows the truck is used and drivin on the road.
__________________
a wise man once said "There are only two real rules to life... 1 - Don't sweat the small stuff 2 - Everything is small stuff |
![]() |
![]() |
![]() |
Bookmarks |
|
|