![]() |
Register or Log In To remove these advertisements. |
|
|
![]() |
|
Thread Tools | Display Modes |
|
![]() |
#1 |
Registered User
Join Date: Jan 2007
Location: Buckeye state
Posts: 168
|
Help! power steering pulley not lining up
I bought this truck and it's a 1977 with a supposed 1985 350 in it.
The pulley is off about a 1/4 inch to the crank. Anyone have any ideas? Has anyone ran into this problem?? I'm thinking of getting a adjustable mount from summit. Anyone have any luck with these? [zoop] Should I try a double groove pulley? Where would be a good place to get one? |
![]() |
![]() |
![]() |
#2 |
Right turn Clyde
Join Date: Nov 2002
Location: Cincinnati, Ohio
Posts: 2,911
|
Re: Help! power steering pulley not lining up
Where about in ohio are you?
__________________
1974 C25 LWB: 454 4bbl Carb / TH400 / 3.73 1992 Camaro RS 305 TBI |
![]() |
![]() |
![]() |
#3 |
Registered User
Join Date: Jan 2007
Location: Buckeye state
Posts: 168
|
Re: Help! power steering pulley not lining up
Other side of the state from ya. Warren/Youngstown area.
|
![]() |
![]() |
![]() |
#4 |
Right turn Clyde
Join Date: Nov 2002
Location: Cincinnati, Ohio
Posts: 2,911
|
Re: Help! power steering pulley not lining up
If you want function over form and low cost grab some all thread some washers and nuts. I think its 3/8 16 that you want to get. Cut the threaded rod longer than you need the pieces so you can get it adjusted where you need easier. After you get it all setup you can get some round tube. Cut the round tube down the length of the washers you need. That will replace the washers and clean it up a little bit better than the stack of washers.
__________________
1974 C25 LWB: 454 4bbl Carb / TH400 / 3.73 1992 Camaro RS 305 TBI |
![]() |
![]() |
![]() |
#5 |
Registered User
Join Date: Jan 2007
Location: Buckeye state
Posts: 168
|
Re: Help! power steering pulley not lining up
Looked it over again tonight and I think I might need a triple groove harmonic pulley. Does Anyone know if a 3 groove pulley has the 3rd groove behind the 2 grooves or is it in front.
Does that make sense?? Basically I have a 2 groove pulley and I need the 3rd groove closer to the block. Is that how they come or do they put the 3rd groove on the outside [fan side] |
![]() |
![]() |
![]() |
#6 | |
Until Seventy Times Seven
Join Date: Feb 2005
Location: Rocky Mountain Front Range
Posts: 1,301
|
Re: Help! power steering pulley not lining up
Quote:
__________________
boxRODz 1983 C10 SWB Fleetside When two halves is gone, there's nuthin left. Two nothings is nuthin. That's mathematics son. You can argue with me but you can't argue with figures. Two half nothings is a whole nuthin... |
|
![]() |
![]() |
![]() |
#7 |
Right turn Clyde
Join Date: Nov 2002
Location: Cincinnati, Ohio
Posts: 2,911
|
Re: Help! power steering pulley not lining up
Would you be able to post any pictures of the front of the engine?
__________________
1974 C25 LWB: 454 4bbl Carb / TH400 / 3.73 1992 Camaro RS 305 TBI |
![]() |
![]() |
![]() |
#8 |
The Crazy Machanic
Join Date: Jan 2007
Location: Nokesville Va
Posts: 1,437
|
Re: Help! power steering pulley not lining up
i got my 3 groove pully froma 1963 impala cause when i got my truck it have v belts and the flater belt type.
|
![]() |
![]() |
![]() |
Bookmarks |
|
|