Info needed from the Turbo 400 guys!

[Steve Cole]

Could someone please post some pics showing the proper routing of the wire harness for the pedal mounted T400 kickdown switch? I did a search but didn't find anything.

Thanks!

[Steve Cole]

Beuller?? Anyone?

[Steve Cole]

Ttt.. Anyone????
Posted via Mobile Device

[Steve Cole]

No one? Seriously?
Posted via Mobile Device

[69moneypit]

Try the engine and drivetrain section . That may help .
Posted via Mobile Device

[67chevy1series]

The switch is on the gas pedal bracket for 71-72.. But where is the kick down switch on a 67-70? That's something I've been wanting to know for a long time
Posted via Mobile Device

[Artikgrau325is]

I believe the switch is mounted on the side of the carburetor. At least, that is what I concluded when I did research on how to hook it back up after putting an Edelbrock 1406 on it (I used a nitrous micro switch.)

I'm sure one of the fine posters here has more adequate info, but if there's no responses here I'll take a picture of the factory kickdown on the carb for ya.
Posted via Mobile Device

[twich3136]

i have a th400 with the kick down switch but im pretty sure its supposed to attach to a bracket by the gas pedal. mine was "rigged" to work off the quadrajet. i switched to an edlebrock and couldnt get it to work, so i just tied it up. i have researched it before and im fairly cirtain its supposed to be on the gas pedal.

[Robznob11]

Push button in cab on shift handle works cool.
Posted via Mobile Device

[Steve Cole]

Originally Posted by twich3136

i have a th400 with the kick down switch but im pretty sure its supposed to attach to a bracket by the gas pedal. mine was "rigged" to work off the quadrajet. i switched to an edlebrock and couldnt get it to work, so i just tied it up. i have researched it before and im fairly cirtain its supposed to be on the gas pedal.

I know my switch attaches to the pedal assy., what I don't know is how the harness is routed from the switch to the tranny. Anyone have pics of this?

[twich3136]

i found this on google. its a bit of reading but it might have the answer your looking for.
http://www.google.com/imgres?imgurl=...ed=0CEYQrQMwDQ
it looks like you just run one wire up to the the switch and a hot wire to the fuse block.

[twich3136]

67chevy1series

if i understand right this is the older switch

this is the 71-72 switch

[Steve Cole]

Originally Posted by twich3136

i found this on google. its a bit of reading but it might have the answer your looking for.
it looks like you just run one wire up to the the switch and a hot wire to the fuse block.

Not what I am looking for but thanks anyway. I want to see the path the wire takes as it goes from the switch, through the cab, exits thru the firewall and connects to the tranny.

[turp mcspray]

The wire runs through the same hole/grommet as the oil pressure line, down through the firewall tabs, with the taillight wires, and on to the trans. Sorry, I don't have any pics. Hope this helps!

[Steve Cole]

Thank you Turp! Even without pics, this is the best answer yet.

[72junky]

Same here Turp! That was a BIG help! by the way, I like your picture... Hope you didn't get hurt and the truck survived too.

72junky

[turp mcspray]

Thanks! I wish it was a better pic. My left front tire wasn't to the top of the rock yet, so it actually went a little higher. My wife and kids were with me, and nobody made a peep! It felt like it was going to go over from the driver seat! It survived that rainy and slippery day, but over all, the rock crawling really took a toll on the old blazer.