![]() |
|
![]() |
#1 |
Registered User
Join Date: Mar 2015
Location: Ontario Canada
Posts: 1,515
|
Door weatherstrip
I'm just installing the door weatherstrip, and didn't know if there was supposed to be some sort of cap covering the end at the box? I guess if the hard top was on you wouldn't see it, but with a soft top it looks unfinished.
|
![]() |
![]() |
![]() |
#2 |
Senior Member
![]() Join Date: May 2011
Location: Greencastle PA
Posts: 6,731
|
Re: Door weatherstrip
I think I saw a cap for that in the LMC catalog.
|
![]() |
![]() |
![]() |
#3 |
Registered User
Join Date: Mar 2015
Location: Ontario Canada
Posts: 1,515
|
Re: Door weatherstrip
|
![]() |
![]() |
![]() |
#4 |
Senior Member
![]() Join Date: May 2011
Location: Greencastle PA
Posts: 6,731
|
Re: Door weatherstrip
|
![]() |
![]() |
![]() |
#5 |
Registered User
Join Date: Oct 2009
Location: Great White North
Posts: 1,520
|
Re: Door weatherstrip
I think it is a plug type thing.
__________________
Jeff. '72 Blazer K5 "Camshaft opinions are like belly buttons; everyone has one and no two are alike" My Blazer Build: http://67-72chevytrucks.com/vboard/s...d.php?t=626752 My Engine Build: http://67-72chevytrucks.com/vboard/s...d.php?t=637336 |
![]() |
![]() |
![]() |
#6 |
Registered User
Join Date: Mar 2015
Location: Ontario Canada
Posts: 1,515
|
Re: Door weatherstrip
I'll check with Bill's trucks in the morning. I never think of checking LMC because it's just too expensive for us north of the border especially now that an item that costs $1.00 US will now cost us $1.42 because of the exchange rate, and then we have to add shipping, brokerage, taxes... I'm too old now, but if I had to do it over again I would have moved to the States when I was young.
|
![]() |
![]() |
![]() |
#7 |
Senior Member
![]() Join Date: May 2006
Location: Philadelphia, Pa. 19454
Posts: 9,520
|
Re: Door weatherstrip
JMO, but if you plug it, where will the air go when you collapse the weatherstrip. Could make it hard to close the door
__________________
Semper Fi...Uncle Sam, you da man All parts offered to help are free, unless otherwise noted Dont try this stuff in my build thread, unless you have 55 years of mechanical OTJ training SAFETY FIRST AS usual, off topic They say your mind goes second, can't remember the first Jim |
![]() |
![]() |
![]() |
#8 |
Registered User
Join Date: Mar 2015
Location: Ontario Canada
Posts: 1,515
|
Re: Door weatherstrip
|
![]() |
![]() |
![]() |
#9 |
Senior Member
![]() Join Date: May 2006
Location: Philadelphia, Pa. 19454
Posts: 9,520
|
Re: Door weatherstrip
that's just it, I've never seen it. But, a cover would work. When the door is closed doesn't it pinch it shut, dunno
__________________
Semper Fi...Uncle Sam, you da man All parts offered to help are free, unless otherwise noted Dont try this stuff in my build thread, unless you have 55 years of mechanical OTJ training SAFETY FIRST AS usual, off topic They say your mind goes second, can't remember the first Jim |
![]() |
![]() |
![]() |
#10 |
Senior Member
![]() Join Date: May 2011
Location: Greencastle PA
Posts: 6,731
|
Re: Door weatherstrip
Bill's truck is awesome I bought my sliding hard top windows from him for 80 dollars US.
|
![]() |
![]() |
![]() |
#11 |
Registered User
Join Date: Aug 2014
Location: Minneapolis, MN
Posts: 254
|
Re: Door weatherstrip
The Chevy parts catalog shows a plug there (page 17-6). It must have been made of a softer material than the plugs sold by LMC. The LMC plugs that I tried are too hard and usually pop out when the door is closed.
__________________
72 Ochre Blazer 69 Camaro Z28 Garnet Red 48 Willys (rolled) |
![]() |
![]() |
![]() |
#12 |
Senior Member
![]() Join Date: May 2011
Location: Greencastle PA
Posts: 6,731
|
Re: Door weatherstrip
|
![]() |
![]() |
![]() |
#13 |
Registered User
Join Date: Dec 2009
Location: Independence Mo
Posts: 4,119
|
Re: Door weatherstrip
They weren't glued in from the factory, at least mine weren't. Kind of wish the were so I wouldn't have lost one by blowing it out with the pressure washer.
![]()
__________________
My '72 short bed build. http://www.ls1tech.com/forums/conver...6-0-4l80e.html 5.3 swap into my RUSTY '71 C10 http://ls1tech.com/forums/conversion...71-c-10-a.html |
![]() |
![]() |
![]() |
#14 |
Registered User
Join Date: Mar 2015
Location: Ontario Canada
Posts: 1,515
|
Re: Door weatherstrip
I just picked some up today. I'll glue them in but all the way around to let air escape. I'll post a pic once installed. Thanks for the replies !!
|
![]() |
![]() |
![]() |
#15 |
Registered User
Join Date: Aug 2014
Location: Minneapolis, MN
Posts: 254
|
Re: Door weatherstrip
What is the material of your plugs?. My LMC plugs are made of hard rubber, definitely not like the originals shown above. When inserted without some sort of cement they literally launch 15 feet across the garage (LOL ) when the door is closed. When glued in they inhibit the closing of the door..... curious to see what yours do.
__________________
72 Ochre Blazer 69 Camaro Z28 Garnet Red 48 Willys (rolled) |
![]() |
![]() |
![]() |
#16 |
Senior Member
![]() Join Date: May 2006
Location: Philadelphia, Pa. 19454
Posts: 9,520
|
Re: Door weatherstrip
The way ls1novas is designed makes sense, if you glued the tab in, it would still vent the pressure out the curled up edges
Never saw them before, great info.
__________________
Semper Fi...Uncle Sam, you da man All parts offered to help are free, unless otherwise noted Dont try this stuff in my build thread, unless you have 55 years of mechanical OTJ training SAFETY FIRST AS usual, off topic They say your mind goes second, can't remember the first Jim |
![]() |
![]() |
![]() |
#17 |
Registered User
Join Date: Mar 2015
Location: Ontario Canada
Posts: 1,515
|
Re: Door weatherstrip
Here's mine installed. I only glued a small portion of it so that I could remove them if they don't work out. They are made of hard rubber, and I think they will interfere with the door. I'll know better once I get the doors painted and installed. The ones posted in LS1's post look like they are a softer material and would work better.
Too bad the ear plugs I have here are bright orange !! LOL |
![]() |
![]() |
![]() |
#18 |
Registered User
Join Date: Feb 2003
Location: Santa Ana, CA
Posts: 2,191
|
Re: Door weatherstrip
I have attempted to use the hard rubber plugs as well. Glued them in and they just get squeezed out over and over. I really like the idea of using an ear plug! Color it black with a sharpie and bingo. It should be soft enough to compress when the door closes without wanting to launch itself. The back side of those orange ear plugs also have a nice finished surface that would look perfect.
|
![]() |
![]() |
![]() |
Bookmarks |
|
|