![]() |
Register or Log In To remove these advertisements. |
|
|
![]() |
|
Thread Tools | Display Modes |
|
![]() |
#1 |
Senior Member
Join Date: Jan 2001
Location: Virginia Beach, Va, USA
Posts: 1,677
|
Steering Wheel column cover removal question
I have a dent in my column cover. The round thing where the turn signal and tilt lever go into. I need to remove the collar to fix the same. Any one know how to get it off? I have a private message into Kev's classics but he must be gone for the holidays. I have the steering wheel and everything else removed below it but the cover around the column.
Thanks, Kerry
__________________
1969 Chevelle 1990 IROC Z Convertible 2002 Silverado LT |
![]() |
![]() |
![]() |
#2 |
Old member
Join Date: Jan 2002
Location: Liberty, & Garden City S.C. , U.S.
Posts: 19,936
|
Re: Steering Wheel column cover removal question
It is just slid on over the inside like a skin. It should just slip off.
__________________
1971 LWB Custom, 6.0LS & 4L80E, Speedhut.com GPS speedometer & gauges with A/C. 20" Boss 338's Grey wheels 4 wheel disc brakes. My Driver Seeing the USA in a 71 ![]() Upstate SC GM Truck Club 2013,14 and 2016 Hot Rod Pour Tour http://upstategmtrucks.com/ Get out and drive the truck this summer and have some fun! It sucks not being able to hear! LWB trucks rule, if you don't think so measure your SWB! After talking to tech support at Air Lift I have found out that the kit I need is 60811. Per the measurements I gave them. Ride height of truck inside spring and inside diameter of springs. |
![]() |
![]() |
![]() |
#3 |
Senior Member
Join Date: Jan 2001
Location: Virginia Beach, Va, USA
Posts: 1,677
|
Re: Steering Wheel column cover removal question
I am trying to remove it from the top so I don't have to remove the whole column.
Kerry
__________________
1969 Chevelle 1990 IROC Z Convertible 2002 Silverado LT |
![]() |
![]() |
![]() |
#4 |
Old member
Join Date: Jan 2002
Location: Liberty, & Garden City S.C. , U.S.
Posts: 19,936
|
Re: Steering Wheel column cover removal question
I don't think that you can do that. I'm not certain, maybe some one else knows for sure. Mine was out of the truck.
__________________
1971 LWB Custom, 6.0LS & 4L80E, Speedhut.com GPS speedometer & gauges with A/C. 20" Boss 338's Grey wheels 4 wheel disc brakes. My Driver Seeing the USA in a 71 ![]() Upstate SC GM Truck Club 2013,14 and 2016 Hot Rod Pour Tour http://upstategmtrucks.com/ Get out and drive the truck this summer and have some fun! It sucks not being able to hear! LWB trucks rule, if you don't think so measure your SWB! After talking to tech support at Air Lift I have found out that the kit I need is 60811. Per the measurements I gave them. Ride height of truck inside spring and inside diameter of springs. |
![]() |
![]() |
![]() |
#5 |
Account Suspended
![]() Join Date: Jul 2006
Location: Mesa Arizona
Posts: 294
|
Re: Steering Wheel column cover removal question
Look very close around the seam. You will see a small indent. Use a very small round flat end punch and tap lightly forward. You should see the seam open a little. If it does work your way around the seam in small amounts . You should see the collar moving and sliding off. Be gentle so you don't dent the edge. If the column has had some repaint the paint may act as a seal at the seam. If so go around the seam first with a razor blade to break the paint seal. Any further questions let me know.
|
![]() |
![]() |
![]() |
#6 |
Senior Member
Join Date: Jul 2001
Location: Muskegon,MI,USA
Posts: 6,026
|
Re: Steering Wheel column cover removal question
Is your column a tilt or standard?
Jim
__________________
1971 Shortbox step side 4x4, 350 sbc, 3:07 rear end 1965 Impala SS 400 sbc, Muncie rock crusher 1966 Impala SS 396 bbc, TH 400 1969 El Camino, 350 sbc, TH 350 1971 Snowplow built on a Blazer frame 1972 GMC Short bed, stepside, TH 400, 427 BBC |
![]() |
![]() |
![]() |
#7 | |
Sierra Grande Club
Join Date: Jan 2007
Location: New Mexico USA
Posts: 2,433
|
Re: Steering Wheel column cover removal question
Quote:
s/t
__________________
1971 GMC Sierra Grande, 1/2 ton short wide, original 4 bolt 010 020 block & heads. (matching #'s). 383 stroker, SMI q jet 750 cfm, Lunati Voodoo 60102 cam, Scorpion roller rockers, Spin Tech pro street mufflers with X pipe. ![]() |
|
![]() |
![]() |
![]() |
#8 |
Sierra Grande Club
Join Date: Jan 2007
Location: New Mexico USA
Posts: 2,433
|
Re: Steering Wheel column cover removal question
It must be different on a non tilt. So my pictures won't be much help.
s/t
__________________
1971 GMC Sierra Grande, 1/2 ton short wide, original 4 bolt 010 020 block & heads. (matching #'s). 383 stroker, SMI q jet 750 cfm, Lunati Voodoo 60102 cam, Scorpion roller rockers, Spin Tech pro street mufflers with X pipe. ![]() |
![]() |
![]() |
![]() |
#9 |
Senior Member
Join Date: Jan 2001
Location: Virginia Beach, Va, USA
Posts: 1,677
|
Re: Steering Wheel column cover removal question
I have a tilt column.
Kerry
__________________
1969 Chevelle 1990 IROC Z Convertible 2002 Silverado LT |
![]() |
![]() |
![]() |
#10 |
member #16
![]() Join Date: Dec 1999
Location: Yuba City Ca.
Posts: 3,618
|
Re: Steering Wheel column cover removal question
With a tilt it will just tap off. I use something soft in the turnsignal lever hole to move it.
__________________
john http://67-72chevytrucks.com/vboard/showgroups.php board vendors ![]() http://www.flickr.com/photos/1745471...7602865984234/ |
![]() |
![]() |
![]() |
#11 |
Senior Member
Join Date: Jan 2001
Location: Virginia Beach, Va, USA
Posts: 1,677
|
Re: Steering Wheel column cover removal question
This is removing from the top correct? the tilt column is installed on the truck.
Kerry
__________________
1969 Chevelle 1990 IROC Z Convertible 2002 Silverado LT |
![]() |
![]() |
![]() |
#12 |
Senior Member
Join Date: Jul 2001
Location: Muskegon,MI,USA
Posts: 6,026
|
Re: Steering Wheel column cover removal question
The cover is held on by a slight interference fit. If you spray the parting line with a penetrant it will help the removal of the cover. The cover comes off toward you. The manual recommends using an inside puller but I use a small flat screw driver and gently tap the cover off with the screwdriver tip agains the bottom edge. The cover has to be "worked" off by going around it if you choose to use a screw driver to remove it.
Of course the levers have to be out of the way and remove the flasher button after depressing the switch. Jim
__________________
1971 Shortbox step side 4x4, 350 sbc, 3:07 rear end 1965 Impala SS 400 sbc, Muncie rock crusher 1966 Impala SS 396 bbc, TH 400 1969 El Camino, 350 sbc, TH 350 1971 Snowplow built on a Blazer frame 1972 GMC Short bed, stepside, TH 400, 427 BBC Last edited by JimKshortstep4x4; 12-24-2008 at 09:03 PM. Reason: Spelling |
![]() |
![]() |
![]() |
#13 |
I'M TRUCK CRAZY!
Join Date: Oct 2006
Location: Sachse, TEXAS
Posts: 1,737
|
Re: Steering Wheel column cover removal question
Good info
|
![]() |
![]() |
![]() |
#14 | |
TILT COLUMN GURU
![]() Join Date: Dec 2006
Location: FRESNO CA
Posts: 4,276
|
Re: Steering Wheel column cover removal question
Quote:
Thanks, Kevin
__________________
kevs_classics64 64 Impala SS Conv 72 Blazer 2wd 75 Jimmy 2wd 63 Belair wagon 02 Silverado ext cab. DD RIP EL JAY |
|
![]() |
![]() |
![]() |
Bookmarks |
|
|