1950 Chevy 3600 - Bumper Punchin' - The 1947 - Present Chevrolet & GMC Truck Message Board Network

IvelDesigns · 02-17-2009, 11:20 PM

By request, I'm starting a new build thread before I have the truck in my hands

I will be picking up a 1950 Chevy truck in about 3 weeks and have a pretty aggressive plan and timeline for it.

Basically what I was able to find (with the help of Bob 68327) is a nearly rust free and complete '50 Chevy truck. I haven't looked inside the cab yet, but the outer sheet metal is 100% there. There are a few dents, but nothing major or unrepairable. Since there is no outer rust, I fully expect to find the floor boards rotted. I mean, it's Iowa damn it... there has to be rust somewhere...

Anyways, the plan... Mustang II setup up front running RE7's and 2" drop spindles. The rear will get a wishbone setup also running RE7's. I'm planning for two compressors, a 5 gal tank, and 8 valves. Probably going to stick with 1/4" line as 3/8" is faster than i want it to be. The goal is for the running boards to be level, and less than 1" off the ground when aired out. Also being able to drive in a straight line when aired out is a must. My kids will be in this, so it has to be safe.

I have a 350 4-bolt that is getting sent off to the shop for a good cleaning, crack check and short block build. Not doing anything crazy with it. just a good running, clean looking engine. the engine bay will be highly chromed out and painted.

Inside the cab is going to pretty much remain as is. I'll need to get the seat re-done, but i'm thinking something simple like a grey/black tweed. It also needs new glass all around.

The body, other than banging out a few of the dents to a semi smooth state, will remain as is. I'm a little concerned with the bare metal rusting, so i may possibly consider painting the truck in the fall a flat black. But this summer it's staying as is for sure. I will also be on the look out for a good pin-striper.

wheels and tires: Wide whites all around on black 15" steelies with baby moons.

So yeah, that's the plan. The timeline is to have this back on the road in time for the Midwest Meet the weekend after Memorial Day. If i cannot meet that timeline, it WILL be on the road in time for the Des Moines Good Guys show.

And now for the pics:

Bob 68327 · 02-17-2009, 11:30 PM

Sweet !!! Can't wait . Glad I could help !!

Bob

LuckyHenriksen · 02-17-2009, 11:31 PM

Hottt.... I can't wait for progress. What trans you goin to run?

IvelDesigns · 02-17-2009, 11:38 PM

well, i was thinking about a 4 speed. but i'll probably stick with an automatic. Either way, the shifter is going to be made from chain (like a big motorcycle chain of some sort) and will be about eye level. I'm tossing around ideas for what to use as the actual handle though. A buddy threw out the idea of using an old, non functional pistol, but i'm sure there's a law against that somewhere....

lurch115 · 02-18-2009, 12:04 AM

Quote:

Originally Posted by IvelDesigns

well, i was thinking about a 4 speed. but i'll probably stick with an automatic. Either way, the shifter is going to be made from chain (like a big motorcycle chain of some sort) and will be about eye level. I'm tossing around ideas for what to use as the actual handle though. A buddy threw out the idea of using an old, non functional pistol, but i'm sure there's a law against that somewhere....

lol nice to see you could be original! lol anyways, looks like a pretty solid truck from what i can see.

thirdstreettito · 02-18-2009, 12:12 AM

Sweet new ride!

LuckyHenriksen · 02-18-2009, 12:13 AM

Cool pistol idea... I have seen it before, and I think it would be legal as long as you had the barrel welded shut.

**LockDoc** · 02-18-2009, 08:24 PM

-
Oh Oh, Looks like some midnight oil is going to be burned...

.. Lookin' good Levi. That will make a sweet ride. If you need any pieces, check with me....

LockDoc

kyull67 · 02-18-2009, 08:49 PM

My friend Jill is a good pinstriper. Her father actually owns his own pinstriping and lettering shop and does that full time. He is somewhere in Iowa so if you are interested I could find out exactly where and what his business is called.

jeffspower · 02-18-2009, 09:35 PM

That will make a sweet ride! can't wait to see ya rollin in it

**70C10Toejam** · 02-18-2009, 09:53 PM

Looking good. Heard you was selling the bumper puncher, and I see why. Cant wait to see it rollin' round here.

jbristo67 · 02-26-2009, 12:33 AM

Quote:

Originally Posted by LuckyHenriksen

Cool pistol idea... I have seen it before, and I think it would be legal as long as you had the barrel welded shut.

I wonder how legal that pistol under my fold down console in my 07 is

72BlckButy · 02-18-2009, 10:21 PM

Levi, I can't wait to see how this thing turns out but I had better see it at the All Truck Nat's. I remember seeing that truck posted in another thread.... ahem Bob... and thought it would make one heck of a sweet ride. The plans sound awesome so get your son out there and get to work!

Best of luck with the project!

Bob 68327 · 02-18-2009, 10:26 PM

I never broke any rules I didn't post it for sale

In friendly conversation Levi asked if I knew where he could find one

I said UMMMM Yup ! Bob

72BlckButy · 02-18-2009, 10:39 PM

Quote:

Originally Posted by Bob 68327

I never broke any rules I didn't post it for sale

In friendly conversation Levi asked if I knew where he could find one

I said UMMMM Yup ! Bob

Don't worry I wasn't calling you out... just wanted to state that I remember a few other members that were interested but distance was the main issue. I'm glad to see Levi end up with it because he will build it right. I can't wait to see how it turns out.

**Dieselwrencher** · 02-18-2009, 11:00 PM

Nice find Levi! Have you had any luck getting the red truck sold? This project is going to cause you some major drowsy mornings at work for sure! LOL

IvelDesigns · 02-18-2009, 11:47 PM

thanks for the comments guys. I'm actually going to keep the red truck and keep driving the wheels off it. Now when the family and I head to a show, I'll be driving one, and jackie will be driving the other. She's pretty partial to the '69 and gave me the green light to keep it and get a new project.

I plan to get the bed finished up on this spring/summer on the 69. planning to get some raw steel diamond plate for the whole bed, then getting it rhino lined red.

I plan to do all of the work on the '50 at my house here in waukee instead of my parents place. That should help give me the time to get it done. That and i have a friend who is helping me out too.

Kyle, i will definitely be in touch regarding your pin striping friend.

bad68bowtie · 02-19-2009, 01:47 AM

Bumper punchin'...I like that...

Now if the day would ever come when mine will be doing that

.

thirdstreettito · 02-19-2009, 12:46 PM

Make sure to paint it red and put moons on it. Then park next to the 69!

VA72C10 · 02-19-2009, 04:31 PM

Glad to hear you're keeping the 69 and will get to enjoy it. Will be watching this build... After I finish my 70, I will next build a blazer...then sometime in the future a 49/50 GMC. My best man at my wedding has a 49 GMC that I drool over every time I see it.

72BlckButy · 02-19-2009, 09:00 PM

Levi, I can't remember.... did you notch your frame/bed on the '69? I've seen several members that have actually retained the original floor and just "raised" it to cover the notch.

IvelDesigns · 02-19-2009, 10:05 PM

in the 69 i just notched the frame with a bolt in setup. There's a thread over in the suspension forum where a guy had a good idea for just cutting a trap door in the floor over the pumpkin. That way it's flush, then when it airs out, the door pops open on its own.

regarding the 50, it looks like i'll be bringing it home the weekend of the 28th. can't wait!

Bob 68327 · 02-19-2009, 10:56 PM

Quote:

Originally Posted by IvelDesigns

in the 69 i just notched the frame with a bolt in setup. There's a thread over in the suspension forum where a guy had a good idea for just cutting a trap door in the floor over the pumpkin. That way it's flush, then when it airs out, the door pops open on its own.

regarding the 50, it looks like i'll be bringing it home the weekend of the 28th. can't wait!

The 28th huh I will have to make sure I'm available

I'm ready when you are to get started !!! Bob

vk_chevy · 02-19-2009, 10:45 PM

that looks like a nice pickup,
good luck and keep us posted.

*Puropedo* · 02-19-2009, 11:04 PM

Great find, I actually wanted that truck, but just like Nate mentioned, distance was an issue. Im glad it is ending up in here (67-72chevytrucks) love what u are planning to do with it, I have similar plans (if I ever get one)
but the wheel tire choice for mine would be 22's rear and 20's front, Im pretty
sure u will do a great job with it!

02-17-2009, 11:20 PM	#1
IvelDesigns Commander Taco Bello Join Date: Sep 2006 Location: Des Moines, Iowa Posts: 2,232	1950 Chevy 3600 - Bumper Punchin' By request, I'm starting a new build thread before I have the truck in my hands I will be picking up a 1950 Chevy truck in about 3 weeks and have a pretty aggressive plan and timeline for it. Basically what I was able to find (with the help of Bob 68327) is a nearly rust free and complete '50 Chevy truck. I haven't looked inside the cab yet, but the outer sheet metal is 100% there. There are a few dents, but nothing major or unrepairable. Since there is no outer rust, I fully expect to find the floor boards rotted. I mean, it's Iowa damn it... there has to be rust somewhere... Anyways, the plan... Mustang II setup up front running RE7's and 2" drop spindles. The rear will get a wishbone setup also running RE7's. I'm planning for two compressors, a 5 gal tank, and 8 valves. Probably going to stick with 1/4" line as 3/8" is faster than i want it to be. The goal is for the running boards to be level, and less than 1" off the ground when aired out. Also being able to drive in a straight line when aired out is a must. My kids will be in this, so it has to be safe. I have a 350 4-bolt that is getting sent off to the shop for a good cleaning, crack check and short block build. Not doing anything crazy with it. just a good running, clean looking engine. the engine bay will be highly chromed out and painted. Inside the cab is going to pretty much remain as is. I'll need to get the seat re-done, but i'm thinking something simple like a grey/black tweed. It also needs new glass all around. The body, other than banging out a few of the dents to a semi smooth state, will remain as is. I'm a little concerned with the bare metal rusting, so i may possibly consider painting the truck in the fall a flat black. But this summer it's staying as is for sure. I will also be on the look out for a good pin-striper. wheels and tires: Wide whites all around on black 15" steelies with baby moons. So yeah, that's the plan. The timeline is to have this back on the road in time for the Midwest Meet the weekend after Memorial Day. If i cannot meet that timeline, it WILL be on the road in time for the Des Moines Good Guys show. And now for the pics: Attached Images __________________ Bagged '50 3600 - Bumper punchin' road kill since 2009... Bagged '69 C10 Longbed - Bumper punchin' road kill since 2007... Last edited by IvelDesigns; 02-17-2009 at 11:35 PM.

02-17-2009, 11:30 PM	#2
Bob 68327 72 Chevelle Club Join Date: Jun 2007 Location: Newton , Iowa Posts: 2,052	Re: 1950 Chevy 3600 - Bumper Punchin' Sweet !!! Can't wait . Glad I could help !! Bob __________________ I Have The Right To Remain Silent,But Lack The Ability 1972 Chevelle ... Mine 2006 Trailblazer... Hers 2002 Buick century ... Kids 2002 K1500 Z-71 EXT CAB ... Daily Driver 2005 Rockwood Roo ... For Camping 1974 Harley-Davidson XLH Sportster 84'' stroker

02-17-2009, 11:31 PM	#3
LuckyHenriksen Registered User Join Date: Oct 2007 Location: Sherwood Oregon Posts: 1,908	Re: 1950 Chevy 3600 - Bumper Punchin' Hottt.... I can't wait for progress. What trans you goin to run? __________________ 1968 Yenko Chevy LWB 6.0L/TH400 3/4 Drop Senior Project Build Thread Here

02-17-2009, 11:38 PM	#4
IvelDesigns Commander Taco Bello Join Date: Sep 2006 Location: Des Moines, Iowa Posts: 2,232	Re: 1950 Chevy 3600 - Bumper Punchin' well, i was thinking about a 4 speed. but i'll probably stick with an automatic. Either way, the shifter is going to be made from chain (like a big motorcycle chain of some sort) and will be about eye level. I'm tossing around ideas for what to use as the actual handle though. A buddy threw out the idea of using an old, non functional pistol, but i'm sure there's a law against that somewhere.... __________________ Bagged '50 3600 - Bumper punchin' road kill since 2009... Bagged '69 C10 Longbed - Bumper punchin' road kill since 2007...

02-18-2009, 12:12 AM	#6
thirdstreettito Resident of Here Join Date: May 2008 Location: Wesley Chapel, FL, USA Posts: 7,716	Re: 1950 Chevy 3600 - Bumper Punchin' Sweet new ride! __________________ ~Bradley~ 2004 Black GTO LS2/T56 too much to list Miss having a truck

02-18-2009, 12:13 AM	#7
LuckyHenriksen Registered User Join Date: Oct 2007 Location: Sherwood Oregon Posts: 1,908	Re: 1950 Chevy 3600 - Bumper Punchin' Cool pistol idea... I have seen it before, and I think it would be legal as long as you had the barrel welded shut. __________________ 1968 Yenko Chevy LWB 6.0L/TH400 3/4 Drop Senior Project Build Thread Here

02-18-2009, 08:24 PM	#8
LockDoc The Older Generation Join Date: Aug 2006 Location: Montezuma, Iowa Posts: 25,629	Re: 1950 Chevy 3600 - Bumper Punchin' - Oh Oh, Looks like some midnight oil is going to be burned..... Lookin' good Levi. That will make a sweet ride. If you need any pieces, check with me.... LockDoc __________________ Leon Locksmith, Specializing In Antique Trucks, Automobiles, & Motorcycles (My Dually Pickup Project Thread) http://67-72chevytrucks.com/vboard/s...d.php?t=829820 -

02-18-2009, 08:49 PM	#9
kyull67 Registered User Join Date: Nov 2006 Location: Springfield/Kansas City Posts: 1,842	Re: 1950 Chevy 3600 - Bumper Punchin' My friend Jill is a good pinstriper. Her father actually owns his own pinstriping and lettering shop and does that full time. He is somewhere in Iowa so if you are interested I could find out exactly where and what his business is called. Attached Images __________________ The first '67 The current '67 '63 Biscayne

02-18-2009, 09:35 PM	#10
jeffspower Well, Whoop-dee-do! Join Date: Mar 2003 Location: Easton, Mo. pop.- me & scarcely a few others Posts: 2,302	Re: 1950 Chevy 3600 - Bumper Punchin' That will make a sweet ride! can't wait to see ya rollin in it __________________ '68 GMC shortbox 4x4 350/SM465/T221- bought it in '83 SOLD '72 K20 500 Cad/TH400/NP205 SOLD '92 Chevy 2500 6.5 mech TD 4L80E crusty daily driver '72 Monte Carlo... sweet low mile toy '11 Dodge Challenger IE 392 6spd... midlife car

02-18-2009, 09:53 PM	#11
70C10Toejam Hellasick Join Date: Jul 2006 Location: Death Moans, IA Posts: 876	Re: 1950 Chevy 3600 - Bumper Punchin' Looking good. Heard you was selling the bumper puncher, and I see why. Cant wait to see it rollin' round here. __________________ I keep two MAGNUMS in my desk. One's a gun, and I keep it loaded. The other's a bottle and it keeps ME loaded. I'm Tracer Bullet. (Calvin and Hobbes) This life was a test. It was only a test. If this had been an actual life, you would have received instructions on where to go and what to do. RED meat is not bad for you...FUZZY BLUE/GREEN MEAT is bad for you!!!!!!!!!!!!! BUILT FORD TOUGH WITH CHEVY STUFF--sticker at Goodguys

02-18-2009, 10:21 PM	#13
72BlckButy Tot Roddin' Join Date: Apr 2005 Location: Mid-MO Posts: 24,461	Re: 1950 Chevy 3600 - Bumper Punchin' Levi, I can't wait to see how this thing turns out but I had better see it at the All Truck Nat's. I remember seeing that truck posted in another thread.... ahem Bob... and thought it would make one heck of a sweet ride. The plans sound awesome so get your son out there and get to work! Best of luck with the project! __________________ -Nate 1969 CST SWB - Project Blank Slate (4.5/6" ECE Static Drop, 6-lug disc brake upgrade (manual), Billet Specialties Vintec 20x8.5 255/40 (F) 20x10 295/40 (R), 250 I-6) 1960 AMF Skylark - Tot Roddin' (Lowered with custom frame; soon to include custom push bar and interior) 2008 Silverado CrewCab 1LT (5.3L, 3:73, 4x4, LT1, Z-71, Towing Package)

02-18-2009, 10:26 PM	#14
Bob 68327 72 Chevelle Club Join Date: Jun 2007 Location: Newton , Iowa Posts: 2,052	Re: 1950 Chevy 3600 - Bumper Punchin' I never broke any rules I didn't post it for sale In friendly conversation Levi asked if I knew where he could find one I said UMMMM Yup ! Bob __________________ I Have The Right To Remain Silent,But Lack The Ability 1972 Chevelle ... Mine 2006 Trailblazer... Hers 2002 Buick century ... Kids 2002 K1500 Z-71 EXT CAB ... Daily Driver 2005 Rockwood Roo ... For Camping 1974 Harley-Davidson XLH Sportster 84'' stroker

02-18-2009, 11:00 PM	#16
Dieselwrencher 6>8 Plugless........ Join Date: Sep 2007 Location: Prairie City, Ia Posts: 17,139	Re: 1950 Chevy 3600 - Bumper Punchin' Nice find Levi! Have you had any luck getting the red truck sold? This project is going to cause you some major drowsy mornings at work for sure! LOL __________________ Ryan 1972 Chevy Longhorn K30 Cheyenne Super, 359 Inline 6 cylinder, Auto Trans, Tilt, Diesel Tach/Vach, Buckets, Rare Rear 4-link and air ride option Build Thread 1972 GMC Sierra Grande Longhorn 4x4 1972 Chevy Cheyenne Super K20 Long Step side tilt, tach, tow hooks, AC, 350 4 speed 1972 C10 Suburban Custom Deluxe 1969 Chevy milk truck 1971 Camaro RS 5.3 BTR STG3 Cam Super T10 1940 Ford 354 Hemi 46RH Ford 9" on air ride huge project *Tired of spark plugs? Check this out.*

02-18-2009, 11:47 PM	#17
IvelDesigns Commander Taco Bello Join Date: Sep 2006 Location: Des Moines, Iowa Posts: 2,232	Re: 1950 Chevy 3600 - Bumper Punchin' thanks for the comments guys. I'm actually going to keep the red truck and keep driving the wheels off it. Now when the family and I head to a show, I'll be driving one, and jackie will be driving the other. She's pretty partial to the '69 and gave me the green light to keep it and get a new project. I plan to get the bed finished up on this spring/summer on the 69. planning to get some raw steel diamond plate for the whole bed, then getting it rhino lined red. I plan to do all of the work on the '50 at my house here in waukee instead of my parents place. That should help give me the time to get it done. That and i have a friend who is helping me out too. Kyle, i will definitely be in touch regarding your pin striping friend. __________________ Bagged '50 3600 - Bumper punchin' road kill since 2009... Bagged '69 C10 Longbed - Bumper punchin' road kill since 2007...

02-19-2009, 01:47 AM	#18
bad68bowtie On the college boy budget... Join Date: Oct 2005 Location: Athens, Georgia Posts: 370	Re: 1950 Chevy 3600 - Bumper Punchin' Bumper punchin'...I like that... Now if the day would ever come when mine will be doing that . __________________ -'68 C10 short/step- 350/350



Register or Log In To remove these advertisements.

02-19-2009, 12:46 PM	#19
thirdstreettito Resident of Here Join Date: May 2008 Location: Wesley Chapel, FL, USA Posts: 7,716	Re: 1950 Chevy 3600 - Bumper Punchin' Make sure to paint it red and put moons on it. Then park next to the 69! __________________ ~Bradley~ 2004 Black GTO LS2/T56 too much to list Miss having a truck

02-19-2009, 04:31 PM	#20
VA72C10 VA72C10 Join Date: Mar 2008 Location: Midlothian, VA Posts: 25,269	Re: 1950 Chevy 3600 - Bumper Punchin' Glad to hear you're keeping the 69 and will get to enjoy it. Will be watching this build... After I finish my 70, I will next build a blazer...then sometime in the future a 49/50 GMC. My best man at my wedding has a 49 GMC that I drool over every time I see it. __________________ Looking for a 67-72 swb or blazer project in or around VA.

02-19-2009, 09:00 PM	#21
72BlckButy Tot Roddin' Join Date: Apr 2005 Location: Mid-MO Posts: 24,461	Re: 1950 Chevy 3600 - Bumper Punchin' Levi, I can't remember.... did you notch your frame/bed on the '69? I've seen several members that have actually retained the original floor and just "raised" it to cover the notch. __________________ -Nate 1969 CST SWB - Project Blank Slate (4.5/6" ECE Static Drop, 6-lug disc brake upgrade (manual), Billet Specialties Vintec 20x8.5 255/40 (F) 20x10 295/40 (R), 250 I-6) 1960 AMF Skylark - Tot Roddin' (Lowered with custom frame; soon to include custom push bar and interior) 2008 Silverado CrewCab 1LT (5.3L, 3:73, 4x4, LT1, Z-71, Towing Package)

02-19-2009, 10:05 PM	#22
IvelDesigns Commander Taco Bello Join Date: Sep 2006 Location: Des Moines, Iowa Posts: 2,232	Re: 1950 Chevy 3600 - Bumper Punchin' in the 69 i just notched the frame with a bolt in setup. There's a thread over in the suspension forum where a guy had a good idea for just cutting a trap door in the floor over the pumpkin. That way it's flush, then when it airs out, the door pops open on its own. regarding the 50, it looks like i'll be bringing it home the weekend of the 28th. can't wait! __________________ Bagged '50 3600 - Bumper punchin' road kill since 2009... Bagged '69 C10 Longbed - Bumper punchin' road kill since 2007...

02-19-2009, 10:45 PM	#24
vk_chevy Registered User Join Date: Jan 2004 Location: Olympia, WA Posts: 231	Re: 1950 Chevy 3600 - Bumper Punchin' that looks like a nice pickup, good luck and keep us posted. __________________ 72 Chevy C20 Longhorn 72 Chevy, K20 Custom Camper 67 Chevy, LWB, C20, 350/350, PS, PB, 65 Jag MKII

02-19-2009, 11:04 PM	#25
Puropedo Account Suspended Join Date: Nov 2008 Location: Prunedale California Posts: 782	Re: 1950 Chevy 3600 - Bumper Punchin' Great find, I actually wanted that truck, but just like Nate mentioned, distance was an issue. Im glad it is ending up in here (67-72chevytrucks) love what u are planning to do with it, I have similar plans (if I ever get one) but the wheel tire choice for mine would be 22's rear and 20's front, Im pretty sure u will do a great job with it!

Register or Log In To remove these advertisements.