hub cap ID and I6 ID - The 1947 - Present Chevrolet & GMC Truck Message Board Network

**67sss** · 11-25-2005, 06:41 PM

what year are these hub caps from, and can someone tell me where the #'s are on this I6? wanna figure year.

Thanks.

davidh · 11-25-2005, 07:14 PM

Those look like chevy Luv hubcaps.

da-burb · 11-25-2005, 07:43 PM

The carb on the 6 banger is 1967 and older. The codes you are looking for iare located just behind the distributor. They will be stamped on the machined pad.

**'68OrangeSunshine** · 11-26-2005, 03:06 AM

Da-Burb is correct that the dress numbers stamped in the pad can tell you what day the engine was originally assembled on. There are also casting numbers above the dipstick that can tell you what day month and year the block was cast. Examples: known '67 292 L6 block --casting #s [CON2 F 22 7] = (CON)veyor line 2, (F)June (22)nd 196(7); dress #s [FO 626 UH] = Flint Michigan, June 26th /not sure what engine codes UH meant, but the LMC catalog lists UH as being on 292s made in '67 and '68. Color may be another clue, I'm not sure what year Chevy Engine Orange came in for L6s, but the first 292s in '63 were apple green, a carryover from the 261s they replaced. Of course a zealous rebuilder could've sprayed a rebuilt engine any color he had a lot of, like orange. Another clue may be the PCV valve line into the carb, early smog gear, which came on line in 1967. Also interesting air cleaner set-up. Is that an oil-bath air cleaner? I think those went out of fashion after '67. [But I could be wrong.]
You can run those numbers on the Inliners International board to learn more about the engine. There is also a casting number after the Conveyor numbers, like 363xxxx that can also be cross referenced.
www.inliners.org
My guess is it's a '67 250 L6.

Tx Firefighter · 11-26-2005, 07:53 AM

OrangeSunshine, that's a power brake air cleaner. It's offest over the engine to allow booster clearance.

I have one on my beater truck. It's probably the most valuable part on the truck.

If the side covers are 4 inches tall, it's a 230 or 250. If they are 6 inches tall, it's a 292. Also, 292's have a bypass hose from the water pump to the thermostat housing, that the 230/250's didn't use.

**'68OrangeSunshine** · 11-27-2005, 06:53 AM

So there will be clearance problems on an L6 w/ a 4Bbl carb and new P/Bk Booster? More pronounced with a 292? My pickup has standard [drum] brakes, but I'm thinking of a 292 and power brakes in some future projects.
I traded out the 14" K&N 'sombrero' air cleaner from the old 292 and put it on the V8 350 [w/600CFM] in the '71 Jimmy, and moved the 12" K&N 'sombrero' to the new L6 292 w/ 500 CFM. Could I get by with a 10" x 5" tall K&N (if they make such a creature) in say a 292 [or bored .060-over, 301"]-powered '72 K/5 w/ P/S + P/Bks ? The Jimmy has factory P/Bks + P/S on a V8. No clearance problems there.

Tx Firefighter · 11-27-2005, 07:11 AM

Orange, I don't know how an aftermarket intake and carb setup will clear.

Here's my stocker on the beater....

**special-K** · 11-27-2005, 07:52 AM

I do think those are LUV caps.That came out funny.

**67sss** · 11-27-2005, 01:21 PM

thanks for the info guys. I know it has the smaller side covers, so it's a 230 or a 250, just have run the #'s to get the year. "LUV" ly caps, thanks special-k

11-25-2005, 06:41 PM	#1
67sss Registered User Join Date: Nov 2002 Location: Mt. Vernon, WA.. Posts: 2,324	hub cap ID and I6 ID what year are these hub caps from, and can someone tell me where the #'s are on this I6? wanna figure year. Thanks. Attached Images

11-25-2005, 07:14 PM	#2
davidh Senior Member Join Date: Feb 2004 Location: Ponca city now kingfisher Oklahoma Posts: 1,221	Re: hub cap ID and I6 ID Those look like chevy Luv hubcaps.

11-25-2005, 07:43 PM	#3
da-burb "Ochre Ogre" Join Date: Apr 2000 Location: Springfield, MN Posts: 3,558	Re: hub cap ID and I6 ID The carb on the 6 banger is 1967 and older. The codes you are looking for iare located just behind the distributor. They will be stamped on the machined pad. __________________ Bowtie Truck Stop Inc. Mid-West GM Truck Restoration Parts Supplier Your Key Parts, Auto Metal Direct, Dynacorn, and Goodmark dealer. like us @ www.facebook.com/BowtieTruckStop 1971 C-10 Suburban (Ochre) 1971 K-10 Suburban (Ochre) 1972 C-10 Suburban (Ochre) 1972 K-20 Suburban (Yellow- that just aint right!) Springfield, Minnesota 56087

11-26-2005, 03:06 AM	#4
'68OrangeSunshine Senior Member Join Date: Feb 2002 Location: Tucson, AZ USA Posts: 7,440	Re: hub cap ID and I6 ID Da-Burb is correct that the dress numbers stamped in the pad can tell you what day the engine was originally assembled on. There are also casting numbers above the dipstick that can tell you what day month and year the block was cast. Examples: known '67 292 L6 block --casting #s [CON2 F 22 7] = (CON)veyor line 2, (F)June (22)nd 196(7); dress #s [FO 626 UH] = Flint Michigan, June 26th /not sure what engine codes UH meant, but the LMC catalog lists UH as being on 292s made in '67 and '68. Color may be another clue, I'm not sure what year Chevy Engine Orange came in for L6s, but the first 292s in '63 were apple green, a carryover from the 261s they replaced. Of course a zealous rebuilder could've sprayed a rebuilt engine any color he had a lot of, like orange. Another clue may be the PCV valve line into the carb, early smog gear, which came on line in 1967. Also interesting air cleaner set-up. Is that an oil-bath air cleaner? I think those went out of fashion after '67. [But I could be wrong.] You can run those numbers on the Inliners International board to learn more about the engine. There is also a casting number after the Conveyor numbers, like 363xxxx that can also be cross referenced. www.inliners.org My guess is it's a '67 250 L6. __________________ Every 25 years I like to rebuild that 292, whether it needs it or not.

11-26-2005, 07:53 AM	#5
Tx Firefighter Watch out for your cornhole ! Join Date: Jun 2003 Location: Azle, Texas Posts: 14,162	Re: hub cap ID and I6 ID OrangeSunshine, that's a power brake air cleaner. It's offest over the engine to allow booster clearance. I have one on my beater truck. It's probably the most valuable part on the truck. If the side covers are 4 inches tall, it's a 230 or 250. If they are 6 inches tall, it's a 292. Also, 292's have a bypass hose from the water pump to the thermostat housing, that the 230/250's didn't use. __________________ I'm on the Instagram- @Gearhead_Kevin

11-27-2005, 06:53 AM	#6
'68OrangeSunshine Senior Member Join Date: Feb 2002 Location: Tucson, AZ USA Posts: 7,440	Re: hub cap ID and I6 ID So there will be clearance problems on an L6 w/ a 4Bbl carb and new P/Bk Booster? More pronounced with a 292? My pickup has standard [drum] brakes, but I'm thinking of a 292 and power brakes in some future projects. I traded out the 14" K&N 'sombrero' air cleaner from the old 292 and put it on the V8 350 [w/600CFM] in the '71 Jimmy, and moved the 12" K&N 'sombrero' to the new L6 292 w/ 500 CFM. Could I get by with a 10" x 5" tall K&N (if they make such a creature) in say a 292 [or bored .060-over, 301"]-powered '72 K/5 w/ P/S + P/Bks ? The Jimmy has factory P/Bks + P/S on a V8. No clearance problems there. __________________ Every 25 years I like to rebuild that 292, whether it needs it or not. Last edited by '68OrangeSunshine; 11-27-2005 at 06:56 AM.

11-27-2005, 07:11 AM	#7
Tx Firefighter Watch out for your cornhole ! Join Date: Jun 2003 Location: Azle, Texas Posts: 14,162	Re: hub cap ID and I6 ID Orange, I don't know how an aftermarket intake and carb setup will clear. Here's my stocker on the beater.... __________________ I'm on the Instagram- @Gearhead_Kevin

11-27-2005, 07:52 AM	#8
special-K Special Order Join Date: Nov 2004 Location: Mt Airy, MD Posts: 85,852	Re: hub cap ID and I6 ID I do think those are LUV caps.That came out funny. __________________ "BUILDING A BETTER WAY TO SERVE THE USA"......67/72......"The New Breed" GMC '67 C1500 Wideside Super Custom SWB: 327/M22/3.42 posi.........."The '67" (project) GMC '72 K2500 Wideside Sierra Custom Camper: 350/TH350/4.10 Power-Lok..."The '72" (rolling) Tim "Don't call me a redneck. I'm a rough cut country gentleman" R.I.P. ~ East Side Low Life ~ El Jay ~ 72BLUZ ~ Fasteddie69 ~ Ron586 ~ 67ChevyRedneck ~ Grumpy Old Man ~

11-27-2005, 01:21 PM	#9
67sss Registered User Join Date: Nov 2002 Location: Mt. Vernon, WA.. Posts: 2,324	Re: hub cap ID and I6 ID thanks for the info guys. I know it has the smaller side covers, so it's a 230 or a 250, just have run the #'s to get the year. "LUV" ly caps, thanks special-k



Register or Log In To remove these advertisements.

Register or Log In To remove these advertisements.