Looking for ideas - Stepside rear bumper - The 1947 - Present Chevrolet & GMC Truck Message Board Network

**JJorgensen52** · 06-11-2011, 08:54 AM

Quote:

Originally Posted by JJorgensen52

My truck currently has the original rusty step bumper installed:

I like the utility of a step bumper, but I HATE this one because of the design - my plate is always getting bent / crushed, it collects a ton of dirt and debris from the bed, and it rattles against the back of the bed. Plus, it's so rotted the step is about to fall off it and I don't use the hitch now that I have a receiver.

I'm looking for ideas / pictures of different bumpers on stepsides - aftermarket, late model, anything different, really. Post up what you've got.

Side note, if anybody in the New England area has a painted sport bumper they'd like to get rid of, I've got an idea for a custom one but I need a bumper to work with.

**EDIT: Now that I've got an idea, this is a follow my crazy idea thread

**

BarryB · 06-11-2011, 09:33 AM

In my opinion, I would get a factory style sport bumper.

*Shane* · 06-11-2011, 10:03 AM

I'm with barry b ... hard to beat the looks of a sport bumper on a stepper.

57larry · 10-22-2011, 06:37 PM

Quote:

Originally Posted by Shane

I'm with barry b ... hard to beat the looks of a sport bumper on a stepper.

X's 2

**mikey531** · 06-11-2011, 11:15 AM

Subscribed, I am looking for ideas too.

**special-K** · 06-11-2011, 11:22 AM

Although sport bumpers look the best,they are worthless from a truck (being used as a truck) point of view. Some sort of step bumper like you have is the way to go to aid in climbing into the bed from the rear and can resist damage way better. I'd remove it and trim it back from the body to allow for drainage and clear the body. If you welded up a frame work to support the inner edge it wouldn't bend very easily.

bobs409 · 06-11-2011, 02:02 PM

My stepside had that bumper on when I got it and I hated it! They look terrible and I was always running my knee into it if I walked around the truck!

I went with the chrome sport type. I don't tow with mine so the sport bumper is good for me. I have the side steps if I need to get into the back.

mgkgmc · 06-11-2011, 02:07 PM

I seen a stepside in one of these threads with chevy colorado bumper mounted on it. It did not look that bad and if its mounted right you could probably tow a light load with it. Or you could go with the Ece hidden hitch on the sport bumper. Just some ideas
Posted via Mobile Device

**JJorgensen52** · 06-11-2011, 07:23 PM

I use this truck as a truck, so a step bumper is my #1 choice.

In doing a little looking around I have a pretty good idea of where I'm going to go with this; I'm going to keep it under wraps for the moment

bollybib · 06-11-2011, 08:32 PM

Quote:

Originally Posted by JJorgensen52

....... I have a pretty good idea of where I'm going to go with this; I'm going to keep it under wraps for the moment

Cool. I like threads with an element of suspense.

**JJorgensen52** · 06-11-2011, 09:35 PM

Quote:

Originally Posted by bollybib

Cool. I like threads with an element of suspense.

I am going to take this in a positive way ... either way, I'm not going to be able to illustrate or describe the idea in my head effectively, so I'm just going to wait until I actually start doing it to post details (pics

)

bollybib · 06-11-2011, 10:17 PM

I look forward to seeing your solution. I didn't mean to sound sarcastic.

mpotts64 · 06-28-2011, 03:07 PM

howdy there again, I am also looking for different things, I have a aftermarket chrome rear step bumper off a '96 S10 that is straight across the top and the bottom bevels down from the outside to the center so the center is about 4" lower than the outsides. It is like 2-3 inches wider than the bed on each side and would have to adapt the arms to fit the frame but I can take some 1/4" plate metal, bend a 90 degree bend in it to bolt to the bottom of the frame and then bolt the arms to the side, I personally do not like the way many bumpers stick way out past the bed but this one would not stick out bad, anyway, I am pondering this situation, best of luck

**JJorgensen52** · 08-21-2011, 06:57 PM

Progress! Finally

Just ordered a set of brackets, should be able to get at least a start this week

Keith Seymore · 08-21-2011, 07:58 PM

Our '69 GMC had the step bumper; I believe it was the factory bumper (not from the dealership).

You can see it here; unfortunately this is the only picture I have of it.

K

**JJorgensen52** · 08-21-2011, 08:56 PM

^^^ That's a nice goat you've got there! Classic picture

Anyway, I do have an option on my SPID for "Rear Step Bumper EQ" - I thought the EQ stood for equivalent, and that the bumpers were region or dealer specific and installed upon delivery? I've never heard of a factory bumper before, though yours looks just like mine. And if anybody would know, I imagine you would!

Keith Seymore · 08-22-2011, 07:29 AM

Unfortunately - I do not remember.

I do still have the goat

but not the truck

K

**JJorgensen52** · 08-26-2011, 04:41 PM

Once again there is going to be a serious lapse in progress

My unit is getting recalled because of this silly hurricane business, so I'll be gone for a bit.

I will finish this bumper at some point, seriously

**JJorgensen52** · 10-18-2011, 05:17 PM

Alright, progress, at last! I am going to pick up the remainder of the steel for the new bumper tomorrow and Thursday afternoon I'm going to start cutting and fitting

Sammy · 10-18-2011, 06:28 PM

Custom ideas for bumpers that are useful are great. Seen a custom bumper on a truck for sale on a 71 LB just the other day. Didn't snap a pic but it really was a lot of work and some serious thought went in to it.

**JJorgensen52** · 10-21-2011, 01:14 AM

Alright, started building today!

(this old bumper has to weigh close to 75lbs)

The top plate for this bumper is 14ga stainless steel (I had it cut/bent by my local sheetmetal supplier)

Now we run into a problem. I measured about 4 times to figure out how much offset I would need, then made myself offset brackets:

When I assembled it, turns out I was 2" off. Still can't figure out how that happened?

Anyway, here's the best solution I could come up with that didn't involve building entirely new brackets

Rough mockup for spacing (just using 2x4 blocks)

And here is where I stopped - started stitching support brackets to the stainless top plate

This is my first experience with welding stainless to mild - some research led me to purchase 309L-16 rod, which makes really pretty welds

More tomorrow

Hopefully I will be able to get this at least 100% together tomorrow. Please excuse the bracketry, I haven't cleaned up any of the welds yet so they are still ugly...

**JJorgensen52** · 10-21-2011, 09:01 PM

This morning, got the rest of the bracketry laid out and tacked together:

Then, cleaned and painted:

And final result:

I think it's a good improvement over the old bumper

I am undecided as of right now if I'm going to leave the stainless bare (I'd at least brush finish it to remove the coloration) or if I'm going to do as planned and put a textured black finish on it - whether stick on non-skid or bedliner, don't know.

tires2burn · 10-22-2011, 12:22 AM

It looks like your really doing a good job on your bumper.I used a astro van bumper. I had to shorten it a little but it fits the lines of the back pretty good. I'll take a few shots of it tomorrow and try to post.

tires2burn · 10-22-2011, 02:47 PM

I got some pics today and if I can get them posted you can see what I got for a step bumper. Had to make my brackets but not a big problem. When I cut the bumper in half I figured Id sink the lic plate at the same time. Cut the OEM pad to fit and added a center piece of alum diamond plate. Enjoy the winter up there. I hear its going to be a cold one.

**JJorgensen52** · 10-22-2011, 03:56 PM

That looks pretty good in the color match - I've also seen the 01-05 stepside bumpers that look decent. I'm a sucker for chrome, is all

06-11-2011, 09:33 AM	#2
BarryB Senior Member Join Date: Jul 2006 Location: Blountville, Tn. Posts: 3,904	Re: Looking for ideas - Stepside rear bumper In my opinion, I would get a factory style sport bumper. __________________ We could learn a lot from crayons... Some are sharp; some are pretty;and some are dull. Some have weird names; and all are different colours;but they all have to live in the same box. You may be only one person in the world, But you may also be the world to one person. * Some mistakes are too much fun to only make once. Two rules in life. 1. Never sweat the small stuff! 2. Everything is small stuff!

06-11-2011, 10:03 AM	#3
Shane Account Suspended Join Date: Jun 2000 Location: over yonder Posts: 14,270	Re: Looking for ideas - Stepside rear bumper I'm with barry b ... hard to beat the looks of a sport bumper on a stepper.

06-11-2011, 11:15 AM	#5
mikey531 Senior Member Join Date: Jul 2009 Location: Exeter, NH Posts: 794	Re: Looking for ideas - Stepside rear bumper Subscribed, I am looking for ideas too.

06-11-2011, 11:22 AM	#6
special-K Special Order Join Date: Nov 2004 Location: Mt Airy, MD Posts: 85,852	Re: Looking for ideas - Stepside rear bumper Although sport bumpers look the best,they are worthless from a truck (being used as a truck) point of view. Some sort of step bumper like you have is the way to go to aid in climbing into the bed from the rear and can resist damage way better. I'd remove it and trim it back from the body to allow for drainage and clear the body. If you welded up a frame work to support the inner edge it wouldn't bend very easily. __________________ "BUILDING A BETTER WAY TO SERVE THE USA"......67/72......"The New Breed" GMC '67 C1500 Wideside Super Custom SWB: 327/M22/3.42 posi.........."The '67" (project) GMC '72 K2500 Wideside Sierra Custom Camper: 350/TH350/4.10 Power-Lok..."The '72" (rolling) Tim "Don't call me a redneck. I'm a rough cut country gentleman" R.I.P. ~ East Side Low Life ~ El Jay ~ 72BLUZ ~ Fasteddie69 ~ Ron586 ~ 67ChevyRedneck ~ Grumpy Old Man ~

06-11-2011, 02:02 PM	#7
bobs409 1969 Custom 30 wrecker Join Date: Sep 2001 Location: Pottsville, Pa Posts: 2,611	Re: Looking for ideas - Stepside rear bumper My stepside had that bumper on when I got it and I hated it! They look terrible and I was always running my knee into it if I walked around the truck! I went with the chrome sport type. I don't tow with mine so the sport bumper is good for me. I have the side steps if I need to get into the back. __________________ Bob 63 Impala 283/PG/3.36 (under restoration) 66 Impala 327/PG/3.36 66 Chevelle SS 409/M22/3.55 69 Chevelle 307/PG/3.08 (future restoration) 69 C10 short stepside 454/TH350/3.73 69 Custom 30 tow truck 350/4 spd/4.10 (resto done, CRUISIN TIME!) 71 Cheyenne 20 fleetside 350/4 spd/4.10 71 Chevelle 6/PG/3.08 72 Chevelle 454/M21/4.10

06-11-2011, 02:07 PM	#8
mgkgmc Registered User Join Date: Dec 2007 Location: Glendale Arizona Posts: 1,354	Re: Looking for ideas - Stepside rear bumper I seen a stepside in one of these threads with chevy colorado bumper mounted on it. It did not look that bad and if its mounted right you could probably tow a light load with it. Or you could go with the Ece hidden hitch on the sport bumper. Just some ideas Posted via Mobile Device Last edited by mgkgmc; 06-11-2011 at 02:15 PM.

06-11-2011, 07:23 PM	#9
JJorgensen52 Simple? What's simple? Join Date: Apr 2007 Location: Southeast CT Posts: 1,472	Re: Looking for ideas - Stepside rear bumper I use this truck as a truck, so a step bumper is my #1 choice. In doing a little looking around I have a pretty good idea of where I'm going to go with this; I'm going to keep it under wraps for the moment __________________ CURRENT '50 GMC 100 shortbed Gen IV 4.8 LS - 4L65E (Secret truck, Shhh!!!) Build '63 Buick Wildcat Coupe 401ci Nailhead (Very much in pieces) Photos '66 Impala SS convertible 327-QJet-glide (4 speed swap one of these days...) Photos '69 CST/10 4x4 SWB Stepper 350 2bbl - NV4500/NP241C (Broken Truck!) '72 Sierra Grande 2WD LWB fleetside 350-TH350 Refresh '99 K2500 Silverado RCLB 5.7 Vortec - NV4500/NP241C (Daily) '99 K2500 Suburban 7.4 Vortec - NV4500/NP246 (still working out the bugs) SOLD '71 Custom/10 2WD LWB fleetside - '72 GMC K/3500 Dually (Sold to redryder)

06-11-2011, 10:17 PM	#12
bollybib Registered User Join Date: Nov 2010 Location: Carlsbad, CA Posts: 1,584	Re: Looking for ideas - Stepside rear bumper I look forward to seeing your solution. I didn't mean to sound sarcastic. __________________ - Jim - My Daily Driver is a 1969 Chevrolet Custom/20 Fleetside 350/TH400/Eaton H052 4.10 and its Project thread is here http://67-72chevytrucks.com/vboard/s...d.php?t=456911

06-28-2011, 03:07 PM	#13
mpotts64 Registered User Join Date: Mar 2011 Location: Texarkana, AR Posts: 123	Re: Looking for ideas - Stepside rear bumper howdy there again, I am also looking for different things, I have a aftermarket chrome rear step bumper off a '96 S10 that is straight across the top and the bottom bevels down from the outside to the center so the center is about 4" lower than the outsides. It is like 2-3 inches wider than the bed on each side and would have to adapt the arms to fit the frame but I can take some 1/4" plate metal, bend a 90 degree bend in it to bolt to the bottom of the frame and then bolt the arms to the side, I personally do not like the way many bumpers stick way out past the bed but this one would not stick out bad, anyway, I am pondering this situation, best of luck __________________ No one ever fell to the top of a mountain. When asked why I work on old trucks, I tell them: Been married 27 years, sons are pretty much gone, don't like the wife anymore and don't have a girlfriend, so, gotta do something, the old trucks are cheaper and less drama than a girlfriend - Last edited by mpotts64; 06-28-2011 at 03:10 PM.

08-21-2011, 06:57 PM	#14
JJorgensen52 Simple? What's simple? Join Date: Apr 2007 Location: Southeast CT Posts: 1,472	Re: Looking for ideas - Stepside rear bumper Progress! Finally Just ordered a set of brackets, should be able to get at least a start this week __________________ CURRENT '50 GMC 100 shortbed Gen IV 4.8 LS - 4L65E (Secret truck, Shhh!!!) Build '63 Buick Wildcat Coupe 401ci Nailhead (Very much in pieces) Photos '66 Impala SS convertible 327-QJet-glide (4 speed swap one of these days...) Photos '69 CST/10 4x4 SWB Stepper 350 2bbl - NV4500/NP241C (Broken Truck!) '72 Sierra Grande 2WD LWB fleetside 350-TH350 Refresh '99 K2500 Silverado RCLB 5.7 Vortec - NV4500/NP241C (Daily) '99 K2500 Suburban 7.4 Vortec - NV4500/NP246 (still working out the bugs) SOLD '71 Custom/10 2WD LWB fleetside - '72 GMC K/3500 Dually (Sold to redryder)

08-21-2011, 07:58 PM	#15
Keith Seymore Registered User Join Date: May 2009 Location: Motor City Posts: 9,213	Re: Looking for ideas - Stepside rear bumper Our '69 GMC had the step bumper; I believe it was the factory bumper (not from the dealership). You can see it here; unfortunately this is the only picture I have of it. K __________________ Chevrolet Flint Assembly 1979-1986 GM Full Size Truck Engineering 1986 - 2019 Intro from an Old Assembly Guy: http://67-72chevytrucks.com/vboard/s...d.php?t=342926 My Pontiac story: http://forums.maxperformanceinc.com/...d.php?t=560524 Chevelle intro: http://www.superchevy.com/features/s...hevy-chevelle/

08-21-2011, 08:56 PM	#16
JJorgensen52 Simple? What's simple? Join Date: Apr 2007 Location: Southeast CT Posts: 1,472	Re: Looking for ideas - Stepside rear bumper ^^^ That's a nice goat you've got there! Classic picture Anyway, I do have an option on my SPID for "Rear Step Bumper EQ" - I thought the EQ stood for equivalent, and that the bumpers were region or dealer specific and installed upon delivery? I've never heard of a factory bumper before, though yours looks just like mine. And if anybody would know, I imagine you would! __________________ CURRENT '50 GMC 100 shortbed Gen IV 4.8 LS - 4L65E (Secret truck, Shhh!!!) Build '63 Buick Wildcat Coupe 401ci Nailhead (Very much in pieces) Photos '66 Impala SS convertible 327-QJet-glide (4 speed swap one of these days...) Photos '69 CST/10 4x4 SWB Stepper 350 2bbl - NV4500/NP241C (Broken Truck!) '72 Sierra Grande 2WD LWB fleetside 350-TH350 Refresh '99 K2500 Silverado RCLB 5.7 Vortec - NV4500/NP241C (Daily) '99 K2500 Suburban 7.4 Vortec - NV4500/NP246 (still working out the bugs) SOLD '71 Custom/10 2WD LWB fleetside - '72 GMC K/3500 Dually (Sold to redryder) Last edited by JJorgensen52; 08-21-2011 at 10:40 PM.

08-22-2011, 07:29 AM	#17
Keith Seymore Registered User Join Date: May 2009 Location: Motor City Posts: 9,213	Re: Looking for ideas - Stepside rear bumper Unfortunately - I do not remember. I do still have the goat but not the truck K __________________ Chevrolet Flint Assembly 1979-1986 GM Full Size Truck Engineering 1986 - 2019 Intro from an Old Assembly Guy: http://67-72chevytrucks.com/vboard/s...d.php?t=342926 My Pontiac story: http://forums.maxperformanceinc.com/...d.php?t=560524 Chevelle intro: http://www.superchevy.com/features/s...hevy-chevelle/

08-26-2011, 04:41 PM	#18
JJorgensen52 Simple? What's simple? Join Date: Apr 2007 Location: Southeast CT Posts: 1,472	Re: Looking for ideas - Stepside rear bumper Once again there is going to be a serious lapse in progress My unit is getting recalled because of this silly hurricane business, so I'll be gone for a bit. I will finish this bumper at some point, seriously __________________ CURRENT '50 GMC 100 shortbed Gen IV 4.8 LS - 4L65E (Secret truck, Shhh!!!) Build '63 Buick Wildcat Coupe 401ci Nailhead (Very much in pieces) Photos '66 Impala SS convertible 327-QJet-glide (4 speed swap one of these days...) Photos '69 CST/10 4x4 SWB Stepper 350 2bbl - NV4500/NP241C (Broken Truck!) '72 Sierra Grande 2WD LWB fleetside 350-TH350 Refresh '99 K2500 Silverado RCLB 5.7 Vortec - NV4500/NP241C (Daily) '99 K2500 Suburban 7.4 Vortec - NV4500/NP246 (still working out the bugs) SOLD '71 Custom/10 2WD LWB fleetside - '72 GMC K/3500 Dually (Sold to redryder)

10-18-2011, 05:17 PM	#19
JJorgensen52 Simple? What's simple? Join Date: Apr 2007 Location: Southeast CT Posts: 1,472	Re: Looking for ideas - Stepside rear bumper Alright, progress, at last! I am going to pick up the remainder of the steel for the new bumper tomorrow and Thursday afternoon I'm going to start cutting and fitting __________________ CURRENT '50 GMC 100 shortbed Gen IV 4.8 LS - 4L65E (Secret truck, Shhh!!!) Build '63 Buick Wildcat Coupe 401ci Nailhead (Very much in pieces) Photos '66 Impala SS convertible 327-QJet-glide (4 speed swap one of these days...) Photos '69 CST/10 4x4 SWB Stepper 350 2bbl - NV4500/NP241C (Broken Truck!) '72 Sierra Grande 2WD LWB fleetside 350-TH350 Refresh '99 K2500 Silverado RCLB 5.7 Vortec - NV4500/NP241C (Daily) '99 K2500 Suburban 7.4 Vortec - NV4500/NP246 (still working out the bugs) SOLD '71 Custom/10 2WD LWB fleetside - '72 GMC K/3500 Dually (Sold to redryder)



Register or Log In To remove these advertisements.

10-18-2011, 06:28 PM	#20
Sammy Registered User Join Date: Apr 2000 Location: Bonne Terre, Mo Posts: 3,005	Re: Looking for ideas - Stepside rear bumper Custom ideas for bumpers that are useful are great. Seen a custom bumper on a truck for sale on a 71 LB just the other day. Didn't snap a pic but it really was a lot of work and some serious thought went in to it. __________________ '69 Chevy Long Fleet & '71 GMC Short Step & Project "ODD BALL" "You can wash a pig, soak it in most expensive perfume. In the end it is still just a pig." ODD BALL build thread http://67-72chevytrucks.com/vboard/s...d.php?t=478629"

10-21-2011, 01:14 AM	#21
JJorgensen52 Simple? What's simple? Join Date: Apr 2007 Location: Southeast CT Posts: 1,472	Re: Looking for ideas - Stepside rear bumper Alright, started building today! (this old bumper has to weigh close to 75lbs) The top plate for this bumper is 14ga stainless steel (I had it cut/bent by my local sheetmetal supplier) Now we run into a problem. I measured about 4 times to figure out how much offset I would need, then made myself offset brackets: When I assembled it, turns out I was 2" off. Still can't figure out how that happened? Anyway, here's the best solution I could come up with that didn't involve building entirely new brackets Rough mockup for spacing (just using 2x4 blocks) And here is where I stopped - started stitching support brackets to the stainless top plate This is my first experience with welding stainless to mild - some research led me to purchase 309L-16 rod, which makes really pretty welds More tomorrow Hopefully I will be able to get this at least 100% together tomorrow. Please excuse the bracketry, I haven't cleaned up any of the welds yet so they are still ugly... __________________ CURRENT '50 GMC 100 shortbed Gen IV 4.8 LS - 4L65E (Secret truck, Shhh!!!) Build '63 Buick Wildcat Coupe 401ci Nailhead (Very much in pieces) Photos '66 Impala SS convertible 327-QJet-glide (4 speed swap one of these days...) Photos '69 CST/10 4x4 SWB Stepper 350 2bbl - NV4500/NP241C (Broken Truck!) '72 Sierra Grande 2WD LWB fleetside 350-TH350 Refresh '99 K2500 Silverado RCLB 5.7 Vortec - NV4500/NP241C (Daily) '99 K2500 Suburban 7.4 Vortec - NV4500/NP246 (still working out the bugs) SOLD '71 Custom/10 2WD LWB fleetside - '72 GMC K/3500 Dually (Sold to redryder)

10-21-2011, 09:01 PM	#22
JJorgensen52 Simple? What's simple? Join Date: Apr 2007 Location: Southeast CT Posts: 1,472	Re: Looking for ideas - Stepside rear bumper This morning, got the rest of the bracketry laid out and tacked together: Then, cleaned and painted: And final result: I think it's a good improvement over the old bumper I am undecided as of right now if I'm going to leave the stainless bare (I'd at least brush finish it to remove the coloration) or if I'm going to do as planned and put a textured black finish on it - whether stick on non-skid or bedliner, don't know. __________________ CURRENT '50 GMC 100 shortbed Gen IV 4.8 LS - 4L65E (Secret truck, Shhh!!!) Build '63 Buick Wildcat Coupe 401ci Nailhead (Very much in pieces) Photos '66 Impala SS convertible 327-QJet-glide (4 speed swap one of these days...) Photos '69 CST/10 4x4 SWB Stepper 350 2bbl - NV4500/NP241C (Broken Truck!) '72 Sierra Grande 2WD LWB fleetside 350-TH350 Refresh '99 K2500 Silverado RCLB 5.7 Vortec - NV4500/NP241C (Daily) '99 K2500 Suburban 7.4 Vortec - NV4500/NP246 (still working out the bugs) SOLD '71 Custom/10 2WD LWB fleetside - '72 GMC K/3500 Dually (Sold to redryder) Last edited by JJorgensen52; 10-22-2011 at 11:04 AM.

10-22-2011, 12:22 AM	#23
tires2burn Registered User Join Date: Apr 2009 Location: Tacoma,Wa Posts: 84	Re: Looking for ideas - Stepside rear bumper It looks like your really doing a good job on your bumper.I used a astro van bumper. I had to shorten it a little but it fits the lines of the back pretty good. I'll take a few shots of it tomorrow and try to post.

10-22-2011, 02:47 PM	#24
tires2burn Registered User Join Date: Apr 2009 Location: Tacoma,Wa Posts: 84	Re: Looking for ideas - Stepside rear bumper I got some pics today and if I can get them posted you can see what I got for a step bumper. Had to make my brackets but not a big problem. When I cut the bumper in half I figured Id sink the lic plate at the same time. Cut the OEM pad to fit and added a center piece of alum diamond plate. Enjoy the winter up there. I hear its going to be a cold one. Attached Images

10-22-2011, 03:56 PM	#25
JJorgensen52 Simple? What's simple? Join Date: Apr 2007 Location: Southeast CT Posts: 1,472	Re: Looking for ideas - Stepside rear bumper That looks pretty good in the color match - I've also seen the 01-05 stepside bumpers that look decent. I'm a sucker for chrome, is all __________________ CURRENT '50 GMC 100 shortbed Gen IV 4.8 LS - 4L65E (Secret truck, Shhh!!!) Build '63 Buick Wildcat Coupe 401ci Nailhead (Very much in pieces) Photos '66 Impala SS convertible 327-QJet-glide (4 speed swap one of these days...) Photos '69 CST/10 4x4 SWB Stepper 350 2bbl - NV4500/NP241C (Broken Truck!) '72 Sierra Grande 2WD LWB fleetside 350-TH350 Refresh '99 K2500 Silverado RCLB 5.7 Vortec - NV4500/NP241C (Daily) '99 K2500 Suburban 7.4 Vortec - NV4500/NP246 (still working out the bugs) SOLD '71 Custom/10 2WD LWB fleetside - '72 GMC K/3500 Dually (Sold to redryder)

Register or Log In To remove these advertisements.