![]() |
Register or Log In To remove these advertisements. |
|
|
![]() |
|
Thread Tools | Display Modes |
|
![]() |
#1 |
Between Trucks...
Join Date: Mar 2002
Location: Los Angeles, CA.
Posts: 3,830
|
Rebuilding Door Hinges
I need to rebuild my drivers side door hinges. Can I just pull the door and do it on the truck, or is it possible to get the hinges off with out pulling the fender? Looks tight there. I'd prefer to do it on the truck, just to make rehanging the door easier.
__________________
Beat it to fit, Paint it to match... ![]() |
![]() |
![]() |
![]() |
#2 |
Registered User
Join Date: Dec 2009
Location: mesa,az
Posts: 94
|
Re: Rebuilding Door Hinges
i dont think u can get them off, but once u do its easy i just bought the kit from inpala bobs for the lower and a new upper they work great.
|
![]() |
![]() |
![]() |
#3 |
Between Trucks...
Join Date: Mar 2002
Location: Los Angeles, CA.
Posts: 3,830
|
Re: Rebuilding Door Hinges
Thanks for the input. I'm going to try pulling the door and doing them on the truck.
__________________
Beat it to fit, Paint it to match... ![]() |
![]() |
![]() |
![]() |
#4 |
Has more rust than truck...
Join Date: Apr 2005
Location: Ivanhoe, MN
Posts: 2,421
|
Re: Rebuilding Door Hinges
I just did my drivers side. I think the only thing that might stop you from doing them on the truck is the amount of force it took me to get the old pins out. I had a BFH and my vise and had to work the top pin back in and out to get it out. Good luck
|
![]() |
![]() |
![]() |
#5 |
Between Trucks...
Join Date: Mar 2002
Location: Los Angeles, CA.
Posts: 3,830
|
Re: Rebuilding Door Hinges
Hmmm. Is your truck apart? I don't have a problem with pulling the hinges, just don't want to have to pull the fender to get them off.
__________________
Beat it to fit, Paint it to match... ![]() |
![]() |
![]() |
![]() |
#6 |
Has more rust than truck...
Join Date: Apr 2005
Location: Ivanhoe, MN
Posts: 2,421
|
Re: Rebuilding Door Hinges
Ya, I had the whole front clip off. I also don't own a torch yet so pb blaster and BFH got the job done.
|
![]() |
![]() |
![]() |
#7 |
Watch out for your cornhole !
![]() Join Date: Jun 2003
Location: Azle, Texas
Posts: 14,162
|
Re: Rebuilding Door Hinges
Clamp the hinge in your vise and use a torch to apply heat to the hinge around the pin area, not on the pin itself. Get them good and warm and the pin comes out every time.
__________________
I'm on the Instagram- @Gearhead_Kevin |
![]() |
![]() |
![]() |
#8 |
Between Trucks...
Join Date: Mar 2002
Location: Los Angeles, CA.
Posts: 3,830
|
Re: Rebuilding Door Hinges
O.K. sounds good. Uhh, am I going to be able to remove the hinges with the fender on?
__________________
Beat it to fit, Paint it to match... ![]() |
![]() |
![]() |
![]() |
#9 |
Grand PooBaa Member
Join Date: Jan 2001
Location: LA, CA
Posts: 5,302
|
Re: Rebuilding Door Hinges
Hey Sin, you just cant get the answer you want about taking the fender off eh buddy. LOL
Im not sure my friend, but I use PB Blaster, it works better than WD-40 or rusted bolts. The torch will work also, just to heat things up. |
![]() |
![]() |
![]() |
#10 |
Between Trucks...
Join Date: Mar 2002
Location: Los Angeles, CA.
Posts: 3,830
|
Re: Rebuilding Door Hinges
LOL, Hey Vince, how's it going? About time for another Board Meet.
__________________
Beat it to fit, Paint it to match... ![]() |
![]() |
![]() |
![]() |
#11 |
Grand PooBaa Member
Join Date: Jan 2001
Location: LA, CA
Posts: 5,302
|
Re: Rebuilding Door Hinges
Hey Bro, your right, it is time for a meet. Im game, still working on the Cam Replacement, due to the rain have not had time. Will try to finish by the weekend coming up. Who wants to host?
|
![]() |
![]() |
![]() |
#12 |
Registered User
Join Date: Sep 2005
Location: Canton North carolina
Posts: 3,079
|
Re: Rebuilding Door Hinges
You can do it with the fender on, but you can not rebuild the hinge on the truck, there is not enough room. You need to get a flex head 9/16 gear wrench and some patience to get at the bolts, but it is no big deal. Use a sharpie to mark the location of the hinges originally and after rebuilt bolt them back on. hope this helps, harold
__________________
67 blue step side- bb 68 gold and white swb cst anniversary 68 custom swb hot rod Ls swap 69 swb cst 6 cylinder/ overdrive 69 black/black cst bb swb 70 orange and white cst Canada built truck swb bb 71 black and white super swb bb 71 red and white super swb 72 green and white super swb 4x4 62 nova wagon 400 series Ls swapped 68 Camaro 327/4 speed- 1 owner, original paint 66 Volkswagen bettle 69 auto stick Volkswagen Beetle |
![]() |
![]() |
![]() |
#13 |
True Addiction
Join Date: Nov 2005
Location: FTL
Posts: 415
|
Re: Rebuilding Door Hinges
Any ideas on how to pull the pins without a torch....? Thanks
__________________
RCC |
![]() |
![]() |
![]() |
#14 |
Registered User
![]() Join Date: Feb 2008
Location: Omaha, NE 68144
Posts: 333
|
Re: Rebuilding Door Hinges
X2 on the propane torch. They are handy if you ever do any plumbing around the house but they can be REAL handy in the garage for getting nuts & bolts loose. Got one that self ignites & has the button to keep it on with just a push. Push button again to turn off quick. Not too expensive either.
__________________
Bryan '52 Bel Air 2dr HT - in pieces '68 C10 - 6cyl/4spd REMOVED, LT1/T56 to be installed “Any society that would give up a little liberty to gain a little security will deserve neither and lose both.” - Benjamin Franklin "And those who know what's best for us, Must rise and save us from ourselves" - RUSH lyric (mockery) |
![]() |
![]() |
![]() |
#15 |
Between Trucks...
Join Date: Mar 2002
Location: Los Angeles, CA.
Posts: 3,830
|
Re: Rebuilding Door Hinges
Try an air hammer with a pointy chisel. I used a propane torch as well, but it might not be necessary. And as an update, I was able to rebuild the hinges on the truck.
__________________
Beat it to fit, Paint it to match... ![]() Last edited by Sinister; 10-21-2010 at 10:03 AM. |
![]() |
![]() |
![]() |
#16 |
Grand PooBaa Member
Join Date: Jan 2001
Location: LA, CA
Posts: 5,302
|
Re: Rebuilding Door Hinges
|
![]() |
![]() |
![]() |
#17 |
Between Trucks...
Join Date: Mar 2002
Location: Los Angeles, CA.
Posts: 3,830
|
Re: Rebuilding Door Hinges
Hey Vince, doing pretty good. How have you been?
__________________
Beat it to fit, Paint it to match... ![]() |
![]() |
![]() |
![]() |
#18 |
Grand PooBaa Member
Join Date: Jan 2001
Location: LA, CA
Posts: 5,302
|
Re: Rebuilding Door Hinges
I've been ok. Trying to enjoy my truck since the new engine got installed.
Also i want to drive it as much as I can, I got an offer, and I might have to take it. So playing when I can. I want to keep it, but,................ |
![]() |
![]() |
![]() |
#19 |
Between Trucks...
Join Date: Mar 2002
Location: Los Angeles, CA.
Posts: 3,830
|
Re: Rebuilding Door Hinges
Hmmmm. You do what you gotta do. Take it easy.
__________________
Beat it to fit, Paint it to match... ![]() |
![]() |
![]() |
![]() |
#20 |
Grand PooBaa Member
Join Date: Jan 2001
Location: LA, CA
Posts: 5,302
|
Re: Rebuilding Door Hinges
|
![]() |
![]() |
![]() |
#21 |
Between Trucks...
Join Date: Mar 2002
Location: Los Angeles, CA.
Posts: 3,830
|
Re: Rebuilding Door Hinges
Yeah, it'd be a bummer to sell it after all the work you just put into it.
A Board meeting would be cool if it's not too far.
__________________
Beat it to fit, Paint it to match... ![]() |
![]() |
![]() |
![]() |
#22 | |
Grand PooBaa Member
Join Date: Jan 2001
Location: LA, CA
Posts: 5,302
|
Re: Rebuilding Door Hinges
Quote:
I figured it was time we came out your way. A few people are talking the IE. Heck it can be something as simple as meeting at a burger stand. More of a catching up meet. |
|
![]() |
![]() |
![]() |
#23 |
Between Trucks...
Join Date: Mar 2002
Location: Los Angeles, CA.
Posts: 3,830
|
Re: Rebuilding Door Hinges
$7000? Yeah, I would have thought about that too.
![]()
__________________
Beat it to fit, Paint it to match... ![]() |
![]() |
![]() |
![]() |
#24 |
Grand PooBaa Member
Join Date: Jan 2001
Location: LA, CA
Posts: 5,302
|
Re: Rebuilding Door Hinges
![]() |
![]() |
![]() |
![]() |
Bookmarks |
|
|